2006 NISSAN VERSA filter

FL-6Revision: June 2006
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
2007 Versa
6. Disconnect electrical connector (A) and fuel feed hose quick
connector (B).

Fuel feed hose (1)

⇐ : Vehicle front

Disconnect the quick connector using the following procedure.
–Hold the sides of the connector, push in tabs and pull out the
tube.
–If quick connector and tube on fuel pump assembly are stuck,
push and pull several times until they move. Disconnect them
by pulling.
CAUTION:

The tube can be removed when the tabs are completely
depressed. Do not twist it more than necessary.

Do not use any tools to remove the quick connector.

Keep resin tube away from heat. Be especially careful
when welding near the resin tube.

Prevent acid liquid such as battery electrolyte, from getting on resin tube.

Do not bend or twist resin tube during installation and removal.

To keep the connecting portion clean, free of foreign
materials and to avoid damage, cover them completely
with plastic bags or something similar.

Do not insert plug to prevent damage to O-ring in quick
connector.
7. Remove the lock ring using Tool as shown.
WBIA0782E
SF E5 62 A
PBIC0163E
Tool number : KV991J0090 (J-46214)
WBIA0284E

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
C
D
E
F
G
H
I
J
K
L
MA
FL
Revision: June 20062007 Versa
8. Remove fuel level sensor unit, fuel filter and fuel pump assembly
(1).
CAUTION:

Do not bend float arm during removal.

Do not allow foreign materials to fall into fuel tank. Use a
lint free cloth when handling components.

Avoid impacts such as dropping when handling compo-
nents.
INSPECTION AFTER REMOVAL
Make sure that the fuel level sensor unit, fuel filter and fuel pump is free from defects and foreign materials.
INSTALLATION
Installation is in the reverse order of removal.
Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly
1. Install O-ring to fuel tank without twisting.
2. Install fuel level sensor unit with aligning mating marks (A) on
fuel tank and fuel level sensor unit as shown.

Turn the lock ring (1) until the lock ring is fully rotated into the
fuel tank lock tabs (A) as shown.
Quick Connector
Connect fuel feed tube quick connector using the following procedure.
1. Check the connection for damage or any foreign materials.
2. Align the connector with the tube, then insert the connector straight into the tube until a “click” sound is
heard.
3. After connecting, make sure that the connection is secure using the following procedure.

Visually confirm that the two retainer tabs are secured to the connector.
PBIC3780E
: Vehicle front
PBIC4732E
WBIA0783E

FL-8Revision: June 2006
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
2007 Versa

Pull the tube and the connector to make sure they are
securely connected.
4. Connect electrical harness connector.
Inspection Hole Cover

Before installing inspection hole cover, confirm that there are no fuel leaks. Refer to FL-8, "INSPECTION
AFTER INSTALLATION" .
1. Install inspection hole cover with the front mark (arrow) facing front of vehicle.
2. Lock clips by turning counterclockwise.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (without starting the engine), to check the connections for fuel leaks with the
electric fuel pump applying pressure to the fuel piping.
2. Start the engine and let it idle to check that there are no fuel leaks at the fuel system connections.
PBIC1653E

IDX-2
ALPHABETICAL INDEX
A
A/C air flow ..................................................... MTC-22
A/C component layout .................................... MTC-17
A/C compressor mounting .............................. MTC-84
A/C compressor precaution .............................. MTC-8
A/C compressor special service tool ............... MTC-12
A/C control operation (manual A/C) ................ MTC-21
A/C controller .................................................. MTC-61
A/C evaporator ................................................ MTC-90
A/C HFC134a (R134a) system precaution ....... MTC-4
A/C HFC134a (R134a) system service procedure .......
MTC-80
A/C HFC134a (R134a) system service tools .. MTC-12
A/C HFC134a system service equipment precaution ...
MTC-9
A/C lubricant (R134a) ........................ MTC-5, MTC-18
A/C lubrication oil ............................................ MTC-96
A/C operational check ..................................... MTC-33
A/C service data specification ......................... MTC-96
A/C trouble diagnoses (manual A/C) .............. MTC-24
A/C unit assembly ........................................... MTC-64
A/C, M - Wiring diagram ................................. MTC-29
A/F - Wiring diagram ... EC-223, EC-229, EC-235, EC-
242, EC-542
A/FH - Wiring diagram ..................................... EC-162
A/T fluid checking .................................. AT-16, MA-22
A/T fluid replacement ............................. AT-17, MA-23
A/T fluid temperature sensor ........................... AT-106
A/T IND - Wiring diagram .................................... DI-38
A/T indicator ........................................................ DI-37
A/T shift control system ................................... AT-229
A/T shift lock system ........................................ AT-235
A/T shift lock system - Wiring diagram ............ AT-236
A/T trouble diagnoses ........................................ AT-43
ABS - Wiring diagram ..................................... BRC-13
ABS (anti-lock brake system) ........................... BRC-5
ABS sensor rotor .............................................. RAX-4
Accelerator pedal position (APP) sensor . EC-513, EC-
519, EC-532
Accelerator pedal released position learning ..... EC-77
Air bag .............................................................. SRS-3
Air bleeding (hydraulic clutch) .............................. CL-8
Air cleaner filter replacement ............................ MA-16
Air conditioner cut control .................................. EC-27
Air fuel ratio sensor 1 .. EC-220, EC-227, EC-233, EC-
239, EC-540
Air fuel ratio sensor 1 heater ............................ EC-161
Air mix door control linkage adjustment .......... MTC-70
Angular tightening application ............................. EM-4
Anti-lock brake system - See ABS .................... BRC-5
Anti-lock brake system - Wiring diagram ........ BRC-13
APPS1 - Wiring diagram .................................. EC-515
APPS2 - Wiring diagram .................................. EC-521
APPS3 - Wiring diagram .................................. EC-534
ASC/BS - Wiring diagram ................................ EC-475
ASC/SW - Wiring diagram ............................... EC-468
ASCBOF - Wiring diagram ............................... EC-550
ASCD ................................................................. EC-28
ASCD brake switch ........................... EC-473, EC-549
ASCD clutch switch ........................... EC-473, EC-549
ASCD steering switch ..................................... EC-466
ASCIND - Wiring diagram ............................... EC-560
AUDIO - Wiring diagram ...................................... AV-9
Auto anti-dazzling inside mirror ........................ GW-67
Axle ................................................................... MA-26
B
BA/FTS - Wiring diagram ................................. AT-171
BACK/L - Wiring diagram ................................... LT-73
Back-up lamp .......................................... LT-73, LT-87
Back-up lamp switch (M/T) ............................... MT-11
Basic inspection ................................................ EC-70
Battery ................................................................. SC-4
Battery/Starting/Charging System Tester SC-6, SC-18,
SC-26
Baulk ring (M/T) ................................................ MT-18
BCM (Body control module) .............................. BCS-3
Blower motor .................................... MTC-37, MTC-68
Blower resistor ................................................ MTC-72
Body alignment ................................................ BL-244
Body component parts ..................................... BL-232
Body construction ............................................ BL-243
Body exterior paint color .................................. BL-231
Body repair ....................................................... BL-231
Body sealing .................................................... BL-240
Brake booster .................................................... BR-19
Brake fluid level ................................................. MA-24
Brake inspection ............................................... MA-25
Brake lines and cables inspection ..................... MA-24
Brake pedal ......................................................... BR-6
Brake switch .................................................... EC-488
BRK/SW - Wiring diagram .............................. EC-489
Bulb specifications ........................................... LT-116
Bumper, front ...................................................... EI-14
C
Cabin air filter .................................................... MA-20
Camshaft ........................................................... EM-47
Camshaft inspection ......................................... EM-49
Camshaft position sensor (PHASE) ................ EC-327
CAN - Wiring diagram ........... EC-152, AT-95, CVT-69
CAN communication EC-30, EC-151, EC-154, AT-31,
AT-94
, CVT-25, CVT-68
CAN communication (EPS) ............................... STC-6
CHARGE - Wiring diagram ............................... SC-25
Charging system ............................................... SC-24
Chassis and body maintenance .............. MA-8, MA-20
CHIME - Wiring diagram ..................................... DI-50
Circuit breaker ................................................... PG-16
Closed loop control ............................. EC-24, EC-442
Clutch cover ....................................................... CL-13
Clutch disc ......................................................... CL-13
Clutch master cylinder ......................................... CL-9
Clutch pedal ......................................................... CL-5
Coil spring (rear) ............................................. RSU-11

IDX-4
ALPHABETICAL INDEX
EC-398, EC-406
EVAP control system pressure sensor .... EC-382, EC-
385, EC-391
EVAP control system purge flow monitoring diagnosis
EC-340
EVAP vapor lines inspection ............................. MA-19
Evaporative emission (EVAP) system ............... EC-31
Evaporator ...................................................... MTC-90
Exhaust manifold .............................................. EM-21
Exhaust system inspection ................... MA-20, MA-22
Expansion valve .............................................. MTC-91
F
F/FOG - Wiring diagram ..................................... LT-43
F/PUMP - Wiring diagram ................................ EC-571
Final drive (FF M/T) ........................................... MT-22
Floor trim ............................................................. EI-37
Flow charts ......................................................... GI-27
Fluid temparature sensor (CVT) ...................... CVT-85
Fluid temperature sensor (A/T) ........................ AT-106
Fluids ................................................................ MA-11
Fluorescent leak detector ............................... MTC-92
Flywheel (clutch) ................................................ CL-13
Flywheel runout .............................................. EM-103
Fork rod (M/T) .................................................... MT-21
Freeze frame data ............................... EC-52, EC-116
Front bumper ...................................................... EI-14
Front door ......................................................... GW-43
Front passenger air bag .................................. SRS-46
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ..... SB-2, SRS-3, SRS-51
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTS - Wiring diagram ......................... AT-103, CVT-86
FTTS - Wiring diagram ...................... EC-293, EC-298
FUEL - Wiring diagram ...................... EC-278, EC-286
Fuel cut control (at no load high engine speed) . EC-26
Fuel gauge ............................................................ DI-5
Fuel injection system ......................... EC-276, EC-284
Fuel injector ..................................................... EC-564
Fuel injector and fuel tube ................................ EM-33
Fuel level sensor ................. EC-415, EC-417, EC-419
Fuel line inspection .................................. FL-4, MA-15
Fuel precautions ................................................... GI-6
Fuel pressure check .......................................... EC-81
Fuel pressure release ........................................ EC-81
Fuel pump ........................................................ EC-570
Fuel systemCommercial Service Tools ................ FL-3
Fuel systemPREPARATION ................................. FL-3
Fuel tank temperature sensor ............ EC-291, EC-297
Fuel tank vacuum relief valve ............................ EC-34
Fuse ................................................................... PG-16
Fuse and fusible link box ................................... PG-77
Fusible link ......................................................... PG-16
G
Gauges ................................................................. DI-5
Gear components (M/T) .................................... MT-18
Generic scan tool (GST) ................................. EC-126
Glass ...................................... GW-11, GW-43, GW-47
Grille - See Exterior ............................................. EI-19
Ground distribution ............................................ PG-30
H
H/LAMP - Wiring diagram .................................... LT-8
H/PHON - Wiring diagram .................................. AV-52
Handling precautions for plastics ..................... BL-255
Harness connector ............................................ PG-68
Harness layout .................................................. PG-39
Hazard warning lamp ......................................... LT-51
Headlining - See Roof trim .................................. EI-39
Heated oxygen sensor 2 ..... EC-248, EC-257, EC-267
Heated oxygen sensor 2 heater ...................... EC-166
HEATER - Wiring diagram .............................. MTC-28
Heater system - Wiring diagram ..................... MTC-28
HFC134a (R134a) system precaution .............. MTC-4
HFC134a (R134a) system service procedure . MTC-80
HFC134a (R134a) system service tools ......... MTC-12
HFC134a system service equipment precaution MTC-9
HO2S2 - Wiring diagram ..... EC-251, EC-260, EC-270
HO2S2H - Wiring diagram .............................. EC-168
Horn ................................................................. WW-46
HORN - Wiring diagram ................................... WW-46
How to erase DTC for OBD system .................. EC-60
I
IATS - Wiring diagram ..................................... EC-197
Idle air volume learning ..................................... EC-78
Idle speed ......................................................... EC-75
Idle speed control (ISC) .................... EC-423, EC-425
Ignition coil ...................................................... EC-576
Ignition control system .................................... EC-576
Ignition timing .................................................... EC-75
IGNSYS - Wiring diagram ............................... EC-577
ILL - Wiring diagram ......................................... LT-111
Illumination control ........................................... LT-108
In-cabin Microfilter ............................................. MA-20
INJECT - Wiring diagram ................................ EC-565
Input shaft (FF M/T) .......................................... MT-18
Input/Output signal of TCM ............................. CVT-25
Instrument panel ................................................. IP-10
INT/L - Wiring diagram ....................................... LT-96
Intake air temperature sensor ........... EC-195, EC-215
Intake door control linkage adjustment ........... MTC-69
Intake manifold .................................................. EM-18
Intake valve timing control .............................. EC-156
Intake valve timing control solenoid valve ....... EC-173
Interior ................................................................. EI-32
Interior lamp ....................................................... LT-91
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-17
IVC - Wiring diagram ....................................... EC-174

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
K
KEYLES - Wiring diagram .................................. BL-57
Knock sensor (KS) .......................................... EC-315
KS - Wiring diagram ........................................ EC-316
L
L/USSV - Wiring diagram .............................. CVT-159
Line pressure and secondary pressure control CVT-26
Line pressure solenoid valve ......... CVT-113, CVT-118
Line pressure test (A/T) ...................................... AT-56
Liquid gasket application ................ EM-5, LU-2, CO-3
Location of electrical units ................................. PG-64
Lock-up and select control .............................. CVT-28
Lock-up select solenoid valve ....................... CVT-158
Low tire pressure warning system ....................... WT-7
Low tire pressure warning system - trouble diagnoses
WT-10
Low tire pressure warning system - Wiring diagram ....
WT-10
LPSV - Wiring diagram .................... AT-146, CVT-114
Lubricant (R134a) A/C ...................... MTC-5, MTC-18
Lubrication circuit (engine) ................................... LU-4
Lubrication oil A/C .......................................... MTC-96
M
M/T major overhaul ........................................... MT-17
M/T removal and installation ............................. MT-15
MAFS - Wiring diagram ..................... EC-181, EC-189
Magnet clutch ................................................. MTC-41
MAIN - Wiring diagram ...................... EC-144, AT-183
Mainshaft (M/T) ................................................. MT-18
Maintenance ........................................................ MA-5
Malfunction indicator lamp (MIL) ....................... EC-61
Manual air conditioner - Wiring diagram ........ MTC-29
Mass air flow sensor (MAFS) ............ EC-178, EC-187
Master cylinder (clutch) ........................................ CL-9
Meter ..................................................................... DI-5
METER - Wiring diagram ...................................... DI-9
MIL data link connectors circuit ....................... EC-592
MIRROR - Wiring diagram ............................... GW-64
Mirror, door ....................................................... GW-65
Mirror, out side ................................................. GW-65
Misfire .............................................................. EC-308
Mode door control linkage adjustment ........... MTC-71
Molding - See Exterior .............................. EI-23, EI-24
Mud guard - See Exterior .................................... EI-26
Multiport fuel injection (MFI) system ................. EC-23
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system - See Remote keyless entry
system ................................................................ BL-54
N
NATS - Wiring diagram .................................... BL-215
NATS (Nissan anti-theft system) precautions ...... GI-3
NONDTC - Wiring diagram ............. AT-193, CVT-176
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (RSU) ............................. RSU-4
NVIS (Nissan vehicle immobilizer system) ....... BL-212
O
Oil change (capacity) ......................................... MA-11
Oil cooler (engine) ............................................. EM-24
Oil filter ................................................................ LU-8
Oil pan (engine) ................................................. EM-24
Oil pressure (engine) ........................................... LU-5
Oil seal replacement (engine) . EM-24, EM-37, EM-59,
EM-66
On board diagnostic system .............................. EC-47
ORVR (On-board Refueling Vapor Recovery) ... EC-38
Out side mirror .................................................. GW-65
Overdrive control switch ..................... AT-186, AT-191
Overheat .......................................................... EC-443
OVRCSV - Wiring diagram .............................. AT-162
P
P/SCKT - Wiring diagram ................................ WW-44
Park/Neutral position switch ............................ EC-436
Park/neutral position switch (A/T) ......... AT-97, AT-186
Park/neutral position switch (CVT) .................. CVT-78
Park/neutral position switch (M/T) ..................... MT-11
Parking brake control ........................................... PB-4
PCV (positive crankcase ventilation) ................. EC-44
Periodic maintenance .......................................... MA-7
PGC/V - Wiring diagram .................... EC-356, EC-364
PHASE - Wiring diagram ................................. EC-329
Pilot bushing replacement ................................. EM-77
Piston assembly ................................................ EM-99
Piston pin inspection .......................................... EM-95
Piston ring inspection ........................................ EM-96
Piston to bore clearance .................................... EM-99
PNP/SW - Wiring diagram ..... EC-438, AT-98, CVT-80
POS - Wiring diagram ...................................... EC-321
POWER - Wiring diagram ................... CVT-146, PG-6
Power door lock .................................................. BL-23
Power socket ................................................... WW-44
Power steering gear .......................................... PS-12
Power supply routing ........................................... PG-4
Power window .................................................. GW-17
PRE/SE - Wiring diagram .................. EC-387, EC-393
Precations for Leak detection dye .................. MTC-10
Precautions (General) .......................................... GI-4
Pressure control solenoid valve A CVT-113, CVT-118
Pressure control solenoid valve B CVT-121, CVT-124
Pressure plate - See Clutch cover ..................... CL-13
Pressure test (CVT) ......................................... CVT-45
Primary pressure sensor ............................... CVT-137
Primary Speed Sensor .................................... CVT-90
PRIPS - Wiring diagram ................................ CVT-138
PRSCVT - Wiring diagram ............................... CVT-91
PT/SEN - Wiring diagram ................................ AT-177

IDX-7
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Trouble diagnoses .............................................. GI-11
TURN - Wiring diagram ...................................... LT-55
Turn signal lamp ................................................. LT-51
Two trip detection logic ..................................... EC-47
V
Vacuum hose (brake system) ........................... BR-22
Vacuum hose drawing (Engine control) .......... EC-102
Valve clearance ................................................. EM-55
Valve guide ....................................................... EM-68
Valve lifter ......................................................... EM-51
Valve seat ......................................................... EM-70
Valve spring ...................................................... EM-71
Vehicle recovery (freeing a stuck vehicle) .......... GI-44
Vehicle security (theft warning) system ............ BL-193
Vehicle speed sensor (VSS) EC-421, EC-485, EC-486
VEHSEC - Wiring diagram ............................... BL-197
VENT/V - Wiring diagram .................. EC-371, EC-378
Ventilation air filter .......................................... MTC-74
VIN registration ................................................. EC-77
Viscosity number (SAE) .................................... MA-12
VSS A/T - Wiring diagram ................................ AT-109
VSSMTR - Wiring diagram ............................... AT-167
W
WARN - Wiring diagram ...................................... DI-25
Warning chime .................................................... DI-47
Warning lamps .................................................... DI-24
Washer, front ..................................................... WW-4
Washer, rear ................................................... WW-30
Water control valve ........................................... CO-20
Water pump ....................................................... CO-17
Water temperature gauge ..................................... DI-5
Wheel alignment (front) ..................................... FSU-6
Wheel alignment (rear) ...................................... RSU-5
Wheel balance ....................................... WT-6, MA-24
Wheel bearing (rear) ......................................... RAX-4
Wheel hub (rear) ............................................... RAX-4
Wheel sensor (VDC) ....................................... BRC-33
Wheel sensors (ABS) ...................................... BRC-11
WINDOW - Wiring diagram .............................. GW-23
Window, door ...................................... GW-43, GW-47
Windshield ........................................................ GW-11
WIP/R - Wiring diagram .................................. WW-33
WIPER - Wiring diagram ................................... WW-9
Wiper, front ........................................................ WW-4
Wiper, rear ...................................................... WW-30
Wiring Diagram (Cell code) list .......................... PG-61
Wiring diagrams ................................................. GI-15

SYSTEM DESCRIPTION
LAN-5
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: June 20062007 Versa
CAN COMMUNICATION CONTROL CIRCUIT
*: These are the only control units wired with both ends of CAN communication system.
SKIB8713E
Component System description
CAN controller It controls CAN communication signal transmission and reception, error detection, etc.
Transceiver ICIt converts digital signal into CAN communication signal, and CAN communication signal into digi-
tal signal.
Noise filter It eliminates noise of CAN communication signal.
Termination circuit
*
(Resistance of approx. 120 Ω)It produces potential difference.