2006 NISSAN VERSA service

SQUEAK AND RATTLE TROUBLE DIAGNOSES
SE-5
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: June 20062007 Versa
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T model, drive position on A/T model).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.

Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.

If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1. Narrow down the noise to a general area.To help pinpoint the source of the noise, use a listening tool
(Chassis Ear: J-39570, Engine Ear: J-39565 and mechanic's stethoscope).
2. Narrow down the noise to a more specific area and identify the cause of the noise by:

removing the components in the area that you suspect the noise is coming from.
Do not use too much force when removing clips and fasteners, otherwise clips and fasteners can be bro-
ken or lost during the repair, resulting in the creation of new noise.

tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only
temporarily.

feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing the
noise.

placing a piece of paper between components that you suspect are causing the noise.

looking for loose components and contact marks.
Refer to SE-6, "
Generic Squeak and Rattle Troubleshooting" .
REPAIR THE CAUSE

If the cause is a loose component, tighten the component securely.

If the cause is insufficient clearance between components:
–separate components by repositioning or loosening and retightening the component, if possible.
–insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. A NISSAN Squeak and Rattle Kit (J-43980) is available through your authorized NISSAN
Parts Department.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
Always check with the Parts Department for the latest parts information.
The following materials are contained in the NISSAN Squeak and Rattle Kit (J-43980). Each item can be
ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
76268-9E005: 100×135 mm (3.94×5.31 in)/76884-71L01: 60×85 mm (2.36×3.35 in)/76884-71L02: 15×25
mm (0.59×0.98 in)
INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
73982-9E000: 45 mm (1.77 in) thick, 50×50 mm (1.97×1.97 in)/73982-50Y00: 10 mm (0.39 in) thick,
50×50 mm (1.97×1.97 in)
INSULATOR (Light foam block)

SRS-1
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
H RESTRAINTS
CONTENTS
C
D
E
F
G
I
J
K
L
M
SECTION SRS
A
B
SRS
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for SRS “AIR BAG” and “SEAT BELT
PRE-TENSIONER” Service ..................................... 3
Occupant Classification System Precaution ............ 3
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) ....... 4
SRS Configuration ................................................... 4
Driver Air Bag Module .............................................. 5
Front Passenger Air Bag Module ............................. 5
Front Side Air Bag .................................................... 5
Side Curtain Air Bag ................................................. 5
Front Seat Belt Pre-tensioner with Load Limiter ...... 6
Occupant Classification System (OCS) ................... 6
Direct-connect SRS Component Connectors ........... 8
TROUBLE DIAGNOSIS .............................................. 9
Trouble Diagnosis Introduction ................................. 9
DIAGNOSIS FUNCTION ....................................... 9
HOW TO PERFORM TROUBLE DIAGNOSES
FOR QUICK AND ACCURATE REPAIR ............... 9
WORK FLOW ...................................................... 10
SRS Components Parts Location ............................11
Schematic .............................................................. 12
Wiring Diagram — SRS — ..................................... 13
CONSULT-II Function (AIR BAG) ........................... 19
HOW TO CHANGE BETWEEN SELF-DIAGNO-
SIS MODE AND USER MODE WITH CONSULT-
II .......................................................................... 19
HOW TO ERASE SELF-DIAGNOSIS RESULTS ... 20
Self-Diagnosis Function (Without CONSULT-II) ..... 20
HOW TO CHANGE BETWEEN USER MODE
AND SELF-DIAGNOSIS MODE WITHOUT
CONSULT-II ........................................................ 21
HOW TO ERASE SELF-DIAGNOSIS RESULTS ... 21
SRS Operation Check ............................................ 21
DIAGNOSTIC PROCEDURE 1 ........................... 21
Trouble Diagnosis With CONSULT-II ..................... 23
DIAGNOSTIC PROCEDURE 2 ........................... 23DIAGNOSTIC PROCEDURE 3 ........................... 27
DIAGNOSTIC PROCEDURE 4 ........................... 29
DIAGNOSTIC PROCEDURE 5 ........................... 29
Trouble Diagnosis Without CONSULT-II ................. 34
DIAGNOSTIC PROCEDURE 6 ........................... 34
WARNING LAMP FLASH CODE CHART ........... 35
Trouble Diagnosis: “AIR BAG” Warning Lamp Does
Not Turn Off ............................................................ 39
DIAGNOSTIC PROCEDURE 7 ........................... 39
Trouble Diagnosis: “AIR BAG” Warning Lamp Does
Not Turn On ............................................................ 40
DIAGNOSTIC PROCEDURE 8 ........................... 40
DRIVER AIR BAG MODULE .................................... 41
Removal and Installation ........................................ 41
REMOVAL ........................................................... 41
INSTALLATION ................................................... 42
SPIRAL CABLE ........................................................ 44
Removal and Installation ........................................ 44
REMOVAL ........................................................... 44
INSTALLATION ................................................... 45
FRONT PASSENGER AIR BAG MODULE .............. 46
Removal and Installation ........................................ 46
REMOVAL ........................................................... 46
INSALLATION ..................................................... 46
SIDE CURTAIN AIR BAG MODULE ........................ 47
Removal and Installation ........................................ 47
REMOVAL ........................................................... 47
INSTALLATION ................................................... 48
CRASH ZONE SENSOR ........................................... 49
Removal and Installation ........................................ 49
REMOVAL ........................................................... 49
INSTALLATION ................................................... 49
SIDE AIR BAG (SATELLITE) SENSOR ................... 50
Removal and Installation ........................................ 50
REMOVAL ........................................................... 50
INSTALLATION ................................................... 50
FRONT SEAT BELT PRE-TENSIONER ................... 51
Removal and Installation ........................................ 51

PRECAUTIONS
SRS-3
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: June 20062007 Versa
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EHS001XL
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WA RN ING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” ServiceEHS001XM

Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.

Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt
pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes
have passed.

The air bag diagnosis sensor unit must always be installed with the arrow mark “⇐” pointing toward the
front of the vehicle for proper operation. Also check air bag diagnosis sensor unit for cracks, deformities or
rust before installation and replace as required.

The spiral cable must be aligned with the neutral position since its rotations are limited. Do not attempt to
turn steering wheel or column after removal of steering gear.

Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad
side facing upward and seat mounted front side air bag module standing with the stud bolt side facing
down.

Conduct self-diagnosis to check entire SRS for proper function after replacing any components.

After air bag inflates, the front instrument panel assembly should be replaced if damaged.

Do not reuse center pillar upper garnish if removed.
Occupant Classification System PrecautionEHS001XN
Replace control unit and passenger front seat cushion as an assembly.

TROUBLE DIAGNOSIS
SRS-9
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: June 20062007 Versa
TROUBLE DIAGNOSISPFP:00004
Trouble Diagnosis IntroductionEHS001UX
CAUTION:

Do not use electrical test equipment on any circuit related to the SRS unless instructed to do so in
this Service Manual.

Do not attempt to repair, splice or modify SRS wiring harnesses. If a harness is damaged, replace
it with a new one.

Keep ground connections clean.
DIAGNOSIS FUNCTION
The SRS self-diagnosis results can be read by using “AIR BAG” warning lamp and/or CONSULT-II.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system mal-
function through the operation of the “AIR BAG” warning lamp.
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the “AIR BAG” warning lamp and CONSULT-II are as follows:
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp-
toms or conditions for a customer complaint.
Information From Customer
WHAT - Vehicle model
WHEN - Date, Frequencies
WHERE - Road conditions
HOW - Operating conditions, Symptoms
Preliminary Check
Check that the following parts are in good order.

Battery (Refer to SC-4, "How to Handle Battery" .)

Fuses (Refer to SRS-12, "Schematic" .)

System component-to-harness connections
User mode Diagnosis mode Display type
“AIR BAG” warning lamp X X ON-OFF operation
CONSULT-II — X Monitoring

STC-1
STEERING CONTROL SYSTEM
G STEERING
CONTENTS
C
D
E
F
H
I
J
K
L
M
SECTION STC
A
B
STC
Revision: June 20062007 Versa
EPS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 3
OPERATION PROCEDURE ................................. 3
Service Notice or Precautions for EPS System ....... 4
EPS SYSTEM ............................................................. 5
System Description .................................................. 5
EPS CONTROL UNIT ........................................... 5
EPS MOTOR ......................................................... 5
TORQUE SENSOR ............................................... 5
REDUCTION GEAR .............................................. 5
EPS WARNING LAMP .......................................... 5
System Diagram ....................................................... 6
COMPONENTS FUNCTION DESCRIPTION ....... 6
CAN Communication ................................................ 6
SYSTEM DESCRIPTION ...................................... 6
TROUBLE DIAGNOSIS .............................................. 7
Fail-Safe Function .................................................... 7
How to Perform Trouble Diagnosis .......................... 7
BASIC CONCEPT ................................................. 7
PRECAUTIONS FOR TROUBLE DIAGNOSIS ..... 7
INTERVIEW .......................................................... 7
Component Parts Location ....................................... 8
Wiring Diagram — EPS — ....................................... 9
EPS Control Unit Input/Output Signal Reference
Values .....................................................................11
SPECIFICATIONS WITH CONSULT-II ................11
SPECIFICATIONS BETWEEN EPS CONTROL
UNIT TERMINALS .............................................. 12
CONSULT-II Function (EPS) .................................. 13
FUNCTION .......................................................... 13
CONSULT-II SETTING PROCEDURE ................ 13
SELF-DIAG RESULTS MODE ............................ 13
DATA MONITOR ................................................. 14
EPS CONTROL UNIT PART NUMBER .............. 14
Symptom Chart ...................................................... 15TROUBLE DIAGNOSIS FOR SYSTEM .................... 16
DTC C1601 BATTERY VOLT ................................. 16
CONSULT-II REFERENCE VALUE IN DATA
MONITOR MODE ................................................ 16
EPS CONTROL UNIT TERMINALS AND REF-
ERENCE VALUE ................................................. 16
DIAGNOSTIC PROCEDURE .............................. 17
DTC C1604 TORQUE SENSOR ............................ 19
CONSULT-II REFERENCE VALUE IN DATA
MONITOR MODE ................................................ 19
EPS CONTROL UNIT TERMINALS AND REF-
ERENCE VALUE ................................................. 19
DIAGNOSTIC PROCEDURE .............................. 19
DTC C1606 EPS MOTOR ...................................... 21
CONSULT-II REFERENCE VALUE IN DATA
MONITOR MODE ................................................ 21
EPS CONTROL UNIT TERMINALS AND REF-
ERENCE VALUE ................................................. 21
DIAGNOSTIC PROCEDURE .............................. 21
DTC C1607 EEPROM ............................................ 22
DIAGNOSTIC PROCEDURE .............................. 22
DTC C1608 CONTROL UNIT ................................. 22
DIAGNOSTIC PROCEDURE .............................. 22
DTC C1609 CAN VHCL SPEED ............................ 23
CONSULT-II REFERENCE VALUE IN DATA
MONITOR MODE ................................................ 23
DIAGNOSTIC PROCEDURE .............................. 23
DTC C1610 CAN ENG RPM .................................. 24
CONSULT-II REFERENCE VALUE IN DATA
MONITOR MODE ................................................ 24
DIAGNOSTIC PROCEDURE .............................. 24
DTC U1000 CAN COMM CIRCUIT ........................ 24
DIAGNOSTIC PROCEDURE .............................. 24
Component Inspection ............................................ 25
EPS MOTOR ....................................................... 25
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 26
EPS Warning Lamp Does Not Turn ON ................. 26
SYMPTOM: ......................................................... 26
DIAGNOSTIC PROCEDURE .............................. 26
EPS Warning Lamp Does Not Turn OFF ................ 27

PRECAUTIONS
STC-3
[EPS]
C
D
E
F
H
I
J
K
L
MA
B
STC
Revision: June 20062007 Versa
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
UGS000A8
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WA RN ING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectUGS000A9
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.

STC-4
[EPS]
PRECAUTIONS
Revision: June 20062007 Versa
Service Notice or Precautions for EPS SystemUGS0008F
CAUTION:
Check or confirm the following item when performing the trouble diagnosis.

Check any possible causes by interviewing the symptom and it’s condition from the customer if
any malfunction, such as EPS warning lamp turns ON, occurs.

Check if air pressure and size of tires are proper, the specified part is used for the steering wheel,
and control unit is genuine part.

Check if the connection of steering column assembly and steering gear assembly is proper (there
is not looseness of mounting bolts, damage of rods, boots or sealants, and leakage of grease,
etc).

Check if the wheel alignment is adjusted properly.

Check if there is any damage or modification to suspension or body resulting in increased weight
or altered ground clearance.

Check if installation conditions of each link and suspension are proper.

Check if the battery voltage is proper

Check connection conditions of each connector are proper.

Before connecting or disconnecting the EPS control unit
harness connector, turn ignition switch “OFF” and discon-
nect battery ground cable. Because battery voltage is
applied to EPS control unit even if ignition switch is turned
“OFF”.

When connecting or disconnecting pin connectors into or
from EPS control unit, take care not to damage pin termi-
nals (bend or break).
When connecting pin connectors, make sure that there are
no bends or breaks on EPS control unit pin terminal.

Before replacing EPS control unit, perform EPS control unit
input/output signal inspection and make sure whether EPS
control unit functions properly or not. Refer to STC-11,
"EPS Control Unit Input/Output Signal Reference Values" .
SEF 2 89 H
SEF 2 91 H
SDIA1848E

WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION WT
A
B
WT
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
PREPARATION ........................................................... 3
Special Service Tool ................................................. 3
Commercial Service Tools ........................................ 3
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 4
NVH Troubleshooting Chart ..................................... 4
ROAD WHEEL ............................................................ 5
Inspection ................................................................. 5
ALUMINUM WHEEL ............................................. 5
STEEL WHEEL ..................................................... 5
ROAD WHEEL TIRE ASSEMBLY .............................. 6
Balancing Wheels .................................................... 6
Rotation .................................................................... 6
LOW TIRE PRESSURE WARNING SYSTEM ............ 7
System Components ................................................ 7
System Description .................................................. 7
BODY CONTROL MODULE (BCM) ...................... 7
TRANSMITTER ..................................................... 8
REMOTE KEYLESS ENTRY RECEIVER ............. 8
COMBINATION METER ....................................... 8
CAN COMMUNICATION ............................................ 9
System Description .................................................. 9
TROUBLE DIAGNOSES .......................................... 10
Wiring Diagram — T/WARN — .............................. 10
Terminals and Reference Values for BCM ..............11
ID Registration Procedure .......................................11
ID REGISTRATION WITH TRANSMITTER
ACTIVATION TOOL .............................................11
ID REGISTRATION WITHOUT TRANSMITTER
ACTIVATION TOOL ............................................ 12
Transmitter Wake Up Operation ............................. 13
CONSULT-II Function (BCM) ................................. 14
How to Perform Trouble Diagnosis for Quick and Accurate Repair ...................................................... 15
INTRODUCTION ................................................. 15
WORK FLOW ...................................................... 15
Preliminary Check .................................................. 16
Self-Diagnosis ........................................................ 16
DESCRIPTION .................................................... 16
FUNCTION .......................................................... 16
Flash Code/Symptom Chart ................................... 19
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 20
Data From Transmitter Not Being Received ........... 20
MALFUNCTION CODE NO. 21, 22, 23 OR 24
(DTC C1708, C1709, C1710 OR C1711) ............ 20
Transmitter Malfunction .......................................... 20
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 ............................... 20
Transmitter Pressure Malfunction ........................... 21
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 21
Vehicle Speed Signal .............................................. 22
MALFUNCTION CODE NO. 52 (DTC C1729) .... 22
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 23
Low Tire Pressure Warning Lamp Does Not Come
On When Ignition Switch Is Turned On. ................. 23
Low Tire Pressure Warning Lamp Stays On When
Ignition Switch Is Turned On .................................. 23
Low Tire Pressure Warning Lamp Flashes When
Ignition Switch Is Turned On. ................................. 25
Hazard Warning Lamps Flash When Ignition Switch
Is Turned On ........................................................... 26
ID Registration Cannot Be Completed ................... 26
REMOVAL AND INSTALLATION ............................. 27
Transmitter (Pressure Sensor) ............................... 27
REMOVAL ........................................................... 27
INSTALLATION ................................................... 27
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 29
Road Wheel ............................................................ 29
Tire ......................................................................... 29