SYSTEM DESCRIPTION
BRC-5
[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: June 20062007 Versa
SYSTEM DESCRIPTIONPFP:00000
System ComponentsEFS006LC
ABS FunctionEFS006LD
The Anti-Lock Brake System detects wheel revolution while braking and improves handling stability during
sudden braking by electrically preventing wheel lockup. Maneuverability is also improved for avoiding
obstacles during emergency braking.
If the electrical system malfunctions, the Fail-Safe function is activated, the ABS becomes inoperative and
the ABS warning lamp turns on.
The electrical system can be diagnosed using CONSULT-II.
During ABS operation, the brake pedal may vibrate lightly and a mechanical noise may be heard. This is
normal.
Just after starting the vehicle, the brake pedal may vibrate or motor operating noises may be heard from
the engine compartment. This is normal due to the self check operation.
Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.
EBD FunctionEFS006LE
Electronic Brake Distribution is a function that detects subtle slippages between the front and rear wheels
during braking, and it improves handling stability by electronically controlling the brake fluid pressure
which results in reduced rear wheel slippage.
If the electrical system malfunctions, the Fail-Safe function is activated, the EBD and ABS become inoper-
ative, and the ABS warning lamp and brake warning lamp are turned on.
The electrical system can be diagnosed using CONSULT-II.
During EBD operation, the brake pedal may vibrate lightly and a mechanical noise may be heard. This is
normal.
Just after starting the vehicle, the brake pedal may vibrate or motor operating noises may be heard from
the engine compartment. This is normal due to the self check operation.
WFIA0118E
BRC-18
[ABS]
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
Warning Lamp and Indicator TimingEFS006LN
Note 1: Brake warning lamp will turn on when the parking brake is applied or when the brake fluid level is low.
x: ON
–: OFF
Control Unit Input/Output Signal StandardEFS006LO
REFERENCE VALUE FROM CONSULT-II
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short circuited.
ConditionABS
warning lampBRAKE
warning lamp
[Note 1]Remarks
When the ignition switch is OFF – – –
After the ignition switch is turned ON for approx. 1
second××–
After the ignition switch is turned ON for approx. 2
seconds––Lamp goes off approx. 2 seconds after the
engine is started.
ABS malfunction×––
EBD malfunction××–
Monitor item Display contentData monitor
Note: Error inspection
checklist
ConditionReference value in
normal operation
FR RH SENSOR
FR LH SENSOR
RR RH SENSOR
RR LH SENSORWheel speedVehicle stopped 0 [km/h (MPH)]
BRC-25, "
Wheel Sensor
System"Vehicle running (Note 1)Almost in accor-
dance with speed-
ometer display
(within ±10%)
BATTERY VOLTBattery voltage sup-
plied to ABS actuator
and electric unit (con-
trol unit)Ignition switch ON 10 to 16VBRC-29, "
ABS Control
Unit Power and Ground
Systems Inspection"
STOP LAMP SWStop lamp switch oper-
ationBrake pedal depressed ON
—
Brake pedal not depressed OFF
ABS WARN LAMPABS warning lamp ON
condition (Note 2)ABS warning lamp ON ONBRC-17, "
ABS WARN-
ING LAMP INSPEC-
TION"ABS warning lamp OFF OFF
MOTOR RELAYOperation status of
motor and motor relayIgnition switch ON or running
(ABS not activated)OFF
BRC-28, "
Actuator Motor,
Motor Relay, and Circuit
Inspection"Ignition switch ON or engine
running (ABS activated)ON
ACTUATOR RLYActuator relay opera-
tion statusVehicle stopped (Ignition
switch ON)OFF
BRC-28, "
Actuator Motor,
Motor Relay, and Circuit
Inspection"Vehicle stopped (Engine run-
ning)ON
FR LH IN SOL
FR LH OUT SOL
FR RH IN SOL
FR RH OUT SOL
RR RH IN SOL
RR RH OUT SOL
RR LH IN SOL
RR LH OUT SOLSolenoid valve opera-
tionActuator (solenoid) is active
(“ACTIVE TEST” with CON-
SULT-II) or actuator relay is
inactive (in fail-safe mode).ON
BRC-27, "
Solenoid Valve
System Inspection"When actuator (solenoid) is
not active and actuator relay is
active (ignition switch ON).OFF
BRC-20
[ABS]
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
CONSULT-II Function (ABS)EFS006LP
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
SELF-DIAGNOSIS
Description
If an error is detected in the system, the ABS warning lamp will turn on. In this case, perform self-diagnosis as
follows:
Operation Procedure
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the data link connector.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
3. Turn ignition switch ON.
4. Start engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
5. After stopping the vehicle, with the engine running, touch “START (NISSAN BASED VHCL)”, “ABS”,
“SELF-DIAG RESULTS” in order on the CONSULT-II screen.
CAUTION:
If “START (NISSAN BASED VHCL)” is touched immediately after starting the engine or turning on
the ignition switch, “ABS” might not be displayed in the SELECT SYSTEM screen. In this case,
repeat the operation from step 1.
6. The self-diagnostic results are displayed. (If necessary, the self-diagnostic results can be printed out by
touching “PRINT”.)
When “NO DTC IS DETECTED” is displayed, check the ABS warning lamp.
7. Conduct the appropriate inspection from the display item list, and repair or replace the malfunctioning
component.
8. Start engine and drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
CAUTION:
When a wheel sensor “short-circuit” is detected, if the vehicle is not driven at 30 km/h (19 MPH)
for at least 1 minute, the ABS warning lamp will not turn off even if the malfunction is repaired.
9. Turn ignition switch OFF to prepare for erasing the memory.
10. Start the engine and touch “START (NISSAN BASED VHCL)”, “ABS”, “SELF-DIAG RESULTS”, “ERASE”
in order on the CONSULT-II screen to erase the error memory.
If “ABS” is not indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC) Circuit" .
CAUTION:
If the error memory is not erased, re-conduct the operation from step 5.
11. For the final inspection, drive at approximately 30 km/h (19 MPH) or more for approximately 1 minute and
confirm that the ABS warning lamp is off.
ABS diagnostic mode Description
SELF-DIAG RESULTS Displays ABS actuator and electric unit (control unit) self-diagnosis results.
DATA MONITOR Displays ABS actuator and electric unit (control unit) input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
FUNCTION TESTConducted by CONSULT-II instead of a technician to determine whether each system is "OK" or
"NG".
ECU PART NUMBER ABS actuator and electric unit (control unit) part number can be read.
BRC-24
[ABS]
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
ACTIVE TEST
CAUTION:
Do not perform active test while driving.
Make sure to completely bleed air from the brake system.
The ABS and brake warning lamps turn on during the active test.
Operation Procedure
1. Connect the CONSULT-II and CONSULT-II CONVERTER to the data link connector and start the engine.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
2. Touch “START (NISSAN BASED VHCL)” on the display screen.
3. Touch “ABS”.
If “ABS” is not indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC) Circuit" .
4. Touch “ACTIVE TEST”.
5. The SELECT TEST ITEM screen is displayed.
6. Touch necessary test item.
7. With the “MAIN SIGNALS” display selected, touch “START”.
8. The Active Test screen will be displayed, so conduct the following test.
Solenoid Valve Operation Chart
NOTE:
If active test is performed with brake pedal depressed, pedal stroke may change. This is normal.
“TEST IS STOPPED” is displayed approximately 10 seconds after operation starts.
After “TEST IS STOPPED” is displayed, to perform test again, repeat Step 6.
ABS Motor
Touch “ON” and “OFF” on the screen. Check that ABS motor relay
operates as shown in table below.
NOTE:
If active test is performed with brake pedal depressed, pedal
stroke may change. This is normal.
“TEST IS STOPPED” is displayed approximately 10 seconds
after operation starts.
WFIA0045E
TEST ITEM CONDITION JUDGEMENT
FR RH SOL
FR LH SOL
RR RH SOL
RR LH SOLIgnition switch is turned ON.Brake fluid pressure control operation
IN SOL OUT SOL
UP (Increase): OFF OFF
KEEP (Hold): ON OFF
DOWN (Decrease): ON ON
Operation ON OFF
ABS actuator relay ON ON
ABS motor relay ON OFF
SFIA0593E
BRC-32
[ABS]
TROUBLE DIAGNOSES FOR SYMPTOMS
Revision: June 20062007 Versa
Long Stopping DistanceEFS006LY
1. CHECK BASE BRAKING SYSTEM PERFORMANCE
1. Disable ABS by disconnecting ABS actuator and electric unit (control unit) connector.
2. Drive vehicle and check brake operation.
NOTE:
Stopping distance may be longer than vehicles without ABS when road condition is slippery.
Driving the vehicle with the ABS actuator and electric unit (control unit) disconnected may induce DTCs
in electrical control units using CAN communication. After the inspection, clear all DTCs. Refer to LAN-
4, "SYSTEM DESCRIPTION" .
OK or NG
OK >> Go to BRC-30, "ABS Works Frequently" .
NG >> Perform Basic Inspection. Refer to BRC-17, "
Basic Inspection" .
ABS Does Not WorkEFS006LZ
CAUTION:
The ABS does not operate when the vehicle speed is 10 km/h (6 MPH) or less.
1. CHECK WARNING LAMP ACTIVATION
Turn ignition switch ON and check for warning lamp activation.
Warning lamp should activate for approximately 2 seconds after turning the ignition switch ON.
OK or NG
OK >> Carry out self-diagnosis. Refer to BRC-20, "SELF-DIAGNOSIS" .
NG >> Go to BRC-17, "
ABS WARNING LAMP INSPECTION" .
Pedal Vibration or ABS Operation NoiseEFS006M0
NOTE:
During ABS activation, pedal vibration may be felt and a noise may be heard. This is normal and does not indi-
cate a malfunction.
1. CHECK SYMPTOM
1. Apply brake.
2. Start engine.
Does the symptom occur only when engine is started?
YES >> Carry out self-diagnosis. Refer to BRC-20, "SELF-DIAGNOSIS" .
NO >> GO TO 2.
2. RECHECK SYMPTOM
Does the symptom occur only when electrical equipment switches (such as headlamps) are turned on?
YES >> Check for radio, antenna or related wiring that is routed too close to the ABS actuator and electric
unit (control unit) and reroute as necessary.
NO >> Go to BRC-30, "
ABS Works Frequently" .
CVT-2Revision: June 20062007 Versa HOW TO ERASE DTC (WITH GST) ................... 32
Malfunction Indicator Lamp (MIL) ........................... 33
DESCRIPTION .................................................... 33
TROUBLE DIAGNOSIS ............................................ 34
DTC Inspection Priority Chart ................................. 34
Fail-safe .................................................................. 34
FAIL-SAFE FUNCTION ....................................... 34
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 35
INTRODUCTION ................................................. 35
WORK FLOW ...................................................... 36
DIAGNOSTIC WORKSHEET .............................. 37
CVT Electrical Parts Location ................................. 40
Circuit Diagram ....................................................... 42
Inspections before Trouble Diagnosis .................... 43
CVT FLUID CHECK ............................................ 43
STALL TEST ........................................................ 43
LINE PRESSURE TEST ...................................... 45
Road Test ............................................................... 46
DESCRIPTION .................................................... 46
CONSULT-II OPERATION PROCEDURE ........... 47
Check before Engine Is Started .............................. 49
Check at Idle ........................................................... 49
Cruise Test .............................................................. 50
Vehicle Speed When Shifting Gears ...................... 53
TCM Input/Output Signal Reference Values ........... 54
TCM TERMINAL CONNECTOR LAYOUT .......... 54
TCM INSPECTION TABLE .................................. 54
CONSULT-II Function (TRANSMISSION) .............. 57
FUNCTION .......................................................... 57
CONSULT-II REFERENCE VALUE ..................... 57
CONSULT-II SETTING PROCEDURE ................ 59
WORK SUPPORT MODE ................................... 59
SELF-DIAGNOSTIC RESULT MODE ................. 60
DATA MONITOR MODE ...................................... 64
CAN DIAGNOSTIC SUPPORT MONITOR
MODE .................................................................. 66
Diagnostic Procedure without CONSULT-II ............ 67
OBD-II SELF-DIAGNOSTIC PROCEDURE
(WITH GST) ......................................................... 67
DTC U1000 CAN COMMUNICATION LINE .............. 68
Description .............................................................. 68
On Board Diagnosis Logic ...................................... 68
Possible Cause ....................................................... 68
DTC Confirmation Procedure ................................. 68
WITH CONSULT-II .............................................. 68
WITH GST ........................................................... 68
Wiring Diagram — CVT — CAN ............................. 69
Diagnostic Procedure ............................................. 70
DTC U1010 TRANSMISSION CONTROL MODULE
(CAN) ......................................................................... 71
Description .............................................................. 71
On Board Diagnosis Logic ...................................... 71
Possible Cause ....................................................... 71
DTC Confirmation Procedure ................................. 71
WITH CONSULT-II .............................................. 71
WITH GST ........................................................... 71
Diagnostic Procedure ............................................. 71
DTC P0615 START SIGNAL CIRCUIT ..................... 72Description ..............................................................72
CONSULT-II Reference Value .................................72
On Board Diagnosis Logic ......................................72
Possible Cause .......................................................72
DTC Confirmation Procedure ..................................72
WITH CONSULT-II ...............................................72
Wiring Diagram — CVT — STSIG ..........................73
Diagnostic Procedure ..............................................74
DTC P0703 STOP LAMP SWITCH CIRCUIT ............76
Description ..............................................................76
CONSULT-II Reference Value .................................76
On Board Diagnosis Logic ......................................76
Possible Cause .......................................................76
DTC Confirmation Procedure ..................................76
WITH CONSULT-II ...............................................76
Diagnostic Procedure ..............................................77
DTC P0705 PARK/NEUTRAL POSITION SWITCH ...78
Description ..............................................................78
CONSULT-II Reference Value .................................78
On Board Diagnosis Logic ......................................78
Possible Cause .......................................................78
DTC Confirmation Procedure ..................................78
WITH CONSULT-II ...............................................79
WITH GST ...........................................................79
Wiring Diagram — CVT — PNP/SW .......................80
Diagnostic Procedure ..............................................82
Component Inspection ............................................84
PNP SWITCH ......................................................84
DTC P0710 CVT FLUID TEMPERATURE SENSOR
CIRCUIT ....................................................................85
Description ..............................................................85
CONSULT-II Reference Value .................................85
On Board Diagnosis Logic ......................................85
Possible Cause .......................................................85
DTC Confirmation Procedure ..................................85
WITH CONSULT-II ...............................................85
WITH GST ...........................................................85
Wiring Diagram — CVT — FTS ..............................86
Diagnostic Procedure ..............................................87
Component Inspection ............................................89
CVT FLUID TEMPERATURE SENSOR ..............89
DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI
SPEED SENSOR) .....................................................90
Description ..............................................................90
CONSULT-II Reference Value .................................90
On Board Diagnosis Logic ......................................90
Possible Cause .......................................................90
DTC Confirmation Procedure ..................................90
WITH CONSULT-II ...............................................90
WITH GST ...........................................................90
Wiring Diagram — CVT — PRSCVT ......................91
Diagnostic Procedure ..............................................92
DTC P0720 VEHICLE SPEED SENSOR CVT (SEC-
ONDARY SPEED SENSOR) .....................................95
Description ..............................................................95
CONSULT-II Reference Value .................................95
On Board Diagnosis Logic ......................................95
Possible Cause .......................................................95
DTC Confirmation Procedure ..................................95
CVT-24
CVT SYSTEM
Revision: June 20062007 Versa
TCM FunctionUCS005XT
The function of the TCM is to:
Receive input signals sent from various switches and sensors.
Determine required line pressure, shifting point, and lock-up operation.
Send required output signals to the step motor and the respective solenoids.
CONTROL SYSTEM OUTLINE
The CVT senses vehicle operating conditions through various sensors. It always controls the optimum shift
position and reduces shifting and lock-up shocks.
CONTROL SYSTEM DIAGRAM
SENSORS (or SIGNAL)
TCM
ACTUATORS
PNP switch
Accelerator pedal position signal
Closed throttle position signal
Engine speed signal
CVT fluid temperature sensor
Vehicle speed signal
Overdrive control signal
Stop lamp switch signal
Primary speed sensor
Secondary speed sensor
Primary pressure sensor
Secondary pressure sensorShift control
Line pressure control
Primary pressure control
Secondary pressure control
Lock-up control
Engine brake control
Vehicle speed control
Fail-safe control
Self-diagnosis
CONSULT-II communication line
Duet-EA control
CAN system
On board diagnosisStep mo to r
Torque converter clutch solenoid
valve
Lock-up select solenoid valve
Line pressure solenoid valve
Secondary pressure solenoid
valve
Shift position indicator
O/D OFF indicator lamp
Starter relay
SCIA7933E
CVT-38
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
4❏ Perform road test.CVT-46
4-1.Check before engine is started CVT-49
❏ CVT-180, "O/D OFF Indicator Lamp Does Not Come On"
❏ Perform self-diagnosis. Enter checks for detected items. CVT-60
❏ CVT-68, "DTC U1000 CAN COMMUNICATION LINE"
❏ CVT-72, "DTC P0615 START SIGNAL CIRCUIT"
❏ CVT-76, "DTC P0703 STOP LAMP SWITCH CIRCUIT"
❏ CVT-78, "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ CVT-85, "DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT"
❏ CVT-90, "DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR)"
❏ CVT-95, "DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED
SENSOR)"
❏ CVT-101, "DTC P0725 ENGINE SPEED SIGNAL"
❏ CVT-103, "DTC P0730 BELT DAMAGE"
❏ CVT-105, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ CVT-110, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ CVT-113, "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ CVT-118, "DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE
(LINE PRESSURE SOLENOID VALVE)"
❏ CVT-121, "DTC P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE
(SEC PRESSURE SOLENOID VALVE)"
❏ CVT-124, "DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC
PRESSURE SOLENOID VALVE)"
❏ CVT-129, "DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT
(SEC PRESSURE SENSOR)"
❏ CVT-134, "DTC P0841 PRESSURE SENSOR FUNCTION"
❏ CVT-137, "DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT
(PRI PRESSURE SENSOR)"
❏ CVT-142, "DTC P0868 SECONDARY PRESSURE DOWN"
❏ CVT-145, "DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)"
❏ CVT-150, "DTC P1705 THROTTLE POSITION SENSOR"
❏ CVT-152, "DTC P1722 ESTM VEHICLE SPEED SIGNAL"
❏ CVT-154, "DTC P1723 CVT SPEED SENSOR FUNCTION"
❏ CVT-156, "DTC P1726 ELECTRIC THROTTLE CONTROL SYSTEM"
❏ CVT-158, "DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT"
❏ CVT-164, "DTC P1777 STEP MOTOR - CIRCUIT"
❏ CVT-168, "DTC P1778 STEP MOTOR - FUNCTION"
4-2.Check at idleCVT-49
❏ CVT-181, "Engine Cannot Be Started in “P” and “N” Position"
❏ CVT-182, "In “P” Position, Vehicle Moves Forward or Backward When Pushed"
❏ CVT-182, "In “N” Position, Vehicle Moves"
❏ CVT-183, "Large Shock “N” → “R” Position"
❏ CVT-184, "Vehicle Does Not Creep Backward in “R” Position"
❏ CVT-185, "Vehicle Does Not Creep Forward in “D” or “L” Position"