2006 NISSAN VERSA belt

CO-16Revision: June 2006
COOLING FAN
2007 Versa
Removal and InstallationEBS00U83
REMOVAL
1. Drain engine coolant from radiator. Refer to CO-8, "DRAINING ENGINE COOLANT" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belt.
2. Remove air duct (inlet). Refer to EM-16, "
Components" .
3. Remove reservoir tank. Refer to CO-11, "
Components" .
4. Disconnect radiator hose (upper) at radiator side. Refer to CO-11, "
Components" .
5. Disconnect harness connectors from fan motor, and move harness to aside.
6. Remove cooling fan assembly.
CAUTION:
Be careful not to damage or scratch the radiator core.
INSTALLATION
Installation is the reverse order of removal.

Cooling fans are controlled by ECM. For details, refer to EC-443, "DTC P1217 ENGINE OVER TEMPER-
AT U R E" .
CAUTION:
Be careful not to damage or scratch the radiator core.
DISASSEMBLY AND ASSEMBLYEBS00V62
DISASSEMBLY
1. Remove cooling fan from fan motor.
2. Remove fan motor from fan shroud.
INSPECTION AFTER DISASSEMBLY
Inspect cooling fan for crack or unusual bend.

If anything is found, replace cooling fan.
ASSEMBLY
Assembly is the reverse order of disassembly.

WATER PUMP
CO-17
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: June 20062007 Versa
WATER P UM PPFP:21020
ComponentsEBS00U84
Removal and InstallationEBS00U85
REMOVAL
1. Drain engine coolant. Refer to CO-8, "DRAINING ENGINE COOLANT" .
CAUTION:
Perform this step when the engine is cold.
2. Remove drive belt auto-tensioner. Refer to EM-37, "
TIMING CHAIN" .
3. Remove water pump.
CAUTION:

Handle water pump vane so that it does not contact any other parts.

Water pump cannot be disassembled and should be replaced as a unit.
INSPECTION AFTER REMOVAL

Visually check that there is no significant dirt or rusting on water
pump body and vane (A).

Make sure that there is no looseness in vane shaft, and that it
turns smoothly when rotated by hand.

Replace water pump, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant. Refer to CO-8, "Inspection" .

Start and warm up the engine. Visually check if there is no leaks of engine coolant.
1. Gasket 2. Water pump
PBIC3921E
PBIC3313J

CVT-1
CVT
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION CVT
A
B
CVT
Revision: June 20062007 Versa INDEX FOR DTC ........................................................ 6
Alphabetical Index .................................................... 6
DTC No. Index ......................................................... 7
PRECAUTIONS .......................................................... 8
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 8
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 8
OPERATION PROCEDURE ................................. 8
Precautions for On Board Diagnostic (OBD) System
of CVT and Engine ................................................... 9
Service After Replacing TCM and Transaxle
Assembly .................................................................. 9
SERVICE AFTER REPLACING TCM AND
TRANSAXLE ASSEMBLY ..................................... 9
PATTERN A .......................................................... 9
PATTERN B .......................................................... 9
PATTERN C .........................................................11
Removal and Installation Procedure for CVT Unit
Connector ................................................................11
REMOVAL ............................................................11
INSTALLATION ................................................... 12
Precautions ............................................................ 13
Service Notice or Precautions ................................ 13
CVT FLUID COOLER SERVICE ......................... 13
OBD-II SELF-DIAGNOSIS .................................. 14
PREPARATION ......................................................... 15
Special Service Tools ............................................. 15
Commercial Service Tools ...................................... 15
CVT FLUID ............................................................... 16
Checking CVT Fluid ............................................... 16
FLUID LEVEL CHECK ........................................ 16
FLUID CONDITION CHECK ............................... 17
Changing CVT Fluid ............................................... 17
CVT Fluid Cooler Cleaning .................................... 18
CVT FLUID COOLER CLEANING PROCEDURE
... 18
CVT FLUID COOLER DIAGNOSIS PROCE-DURE .................................................................. 19
CVT FLUID COOLER INSPECTION PROCE-
DURE .................................................................. 20
CVT FLUID COOLER FINAL INSPECTION ........ 20
CVT SYSTEM ............................................................ 21
Cross-sectional View - RE0F08A ........................... 21
Control System ....................................................... 22
Hydraulic Control System ....................................... 23
TCM Function ......................................................... 24
CONTROL SYSTEM OUTLINE .......................... 24
CONTROL SYSTEM DIAGRAM ......................... 24
CAN Communication .............................................. 25
SYSTEM DESCRIPTION .................................... 25
Input/Output Signal of TCM .................................... 25
Line Pressure and Secondary Pressure Control .... 26
NORMAL CONTROL .......................................... 26
FEEDBACK CONTROL ...................................... 26
Shift Control ............................................................ 26
“D” POSITION ..................................................... 27
OVERDRIVE-OFF MODE ................................... 27
“L” POSITION ...................................................... 27
DOWNHILL ENGINE BRAKE CONTROL (AUTO
ENGINE BRAKE CONTROL) .............................. 27
ACCELERATION CONTROL .............................. 27
Lock-up and Select Control .................................... 28
TORQUE CONVERTER CLUTCH AND SELECT
CONTROL VALVE CONTROL ............................ 28
Control Valve .......................................................... 29
FUNCTION OF CONTROL VALVE ..................... 29
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 30
Introduction ............................................................. 30
OBD-II Function for CVT System ........................... 30
One or Two Trip Detection Logic of OBD-II ............ 30
ONE TRIP DETECTION LOGIC ......................... 30
TWO TRIP DETECTION LOGIC ......................... 30
OBD-II Diagnostic Trouble Code (DTC) ................. 30
HOW TO READ DTC AND 1ST TRIP DTC ......... 30
HOW TO ERASE DTC ........................................ 31
HOW TO ERASE DTC (WITH CONSULT-II) ....... 32

CVT-3
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa WITH CONSULT-II .............................................. 95
WITH GST ........................................................... 95
Wiring Diagram — CVT — SESCVT ...................... 96
Diagnostic Procedure ............................................. 97
DTC P0725 ENGINE SPEED SIGNAL ................... 101
Description ........................................................... 101
CONSULT-II Reference Value .............................. 101
On Board Diagnosis Logic ................................... 101
Possible Cause .................................................... 101
DTC Confirmation Procedure ............................... 101
WITH CONSULT-II ............................................ 101
Diagnostic Procedure ........................................... 101
DTC P0730 BELT DAMAGE .................................. 103
Description ........................................................... 103
CONSULT-II Reference Value .............................. 103
On Board Diagnosis Logic ................................... 103
Possible Cause .................................................... 103
DTC Confirmation Procedure ............................... 103
WITH CONSULT-II ............................................ 103
Diagnostic Procedure ........................................... 104
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE ................................................. 105
Description ........................................................... 105
CONSULT-II Reference Value .............................. 105
On Board Diagnosis Logic ................................... 105
Possible Cause .................................................... 105
DTC Confirmation Procedure ............................... 105
WITH CONSULT-II ............................................ 105
WITH GST ......................................................... 105
Wiring Diagram — CVT — TCV ........................... 106
Diagnostic Procedure ........................................... 107
Component Inspection ......................................... 109
TORQUE CONVERTER CLUTCH SOLENOID
VALVE ............................................................... 109
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) .. 110
Description ............................................................ 110
CONSULT-II Reference Value ............................... 110
On Board Diagnosis Logic .................................... 110
Possible Cause ..................................................... 110
DTC Confirmation Procedure ................................ 110
WITH CONSULT-II ............................................. 110
WITH GST .......................................................... 110
Diagnostic Procedure ........................................... . 111
DTC P0745 LINE PRESSURE SOLENOID VALVE .. 113
Description ............................................................ 113
CONSULT-II Reference Value ............................... 113
On Board Diagnosis Logic .................................... 113
Possible Cause ..................................................... 113
DTC Confirmation Procedure ................................ 113
WITH CONSULT-II ............................................. 113
WITH GST .......................................................... 113
Wiring Diagram — CVT — LPSV .......................... 114
Diagnostic Procedure ............................................ 115
Component Inspection .......................................... 117
PRESSURE CONTROL SOLENOID VALVE A
(LINE PRESSURE SOLENOID VALVE) ............ 117
DTC P0746 PRESSURE CONTROL SOLENOID A
PERFORMANCE (LINE PRESSURE SOLENOID
VALVE) ..................................................................... 118Description ............................................................118
CONSULT-II Reference Value ..............................118
On Board Diagnosis Logic ....................................118
Possible Cause .....................................................118
DTC Confirmation Procedure ...............................118
WITH CONSULT-II ............................................118
WITH GST .........................................................118
Diagnostic Procedure ...........................................119
DTC P0776 PRESSURE CONTROL SOLENOID B
PERFORMANCE (SEC PRESSURE SOLENOID
VALVE) ....................................................................121
Description ............................................................121
CONSULT-II Reference Value ..............................121
On Board Diagnosis Logic ....................................121
Possible Cause .....................................................121
DTC Confirmation Procedure ...............................121
WITH CONSULT-II ............................................121
WITH GST .........................................................121
Diagnostic Procedure ...........................................122
DTC P0778 PRESSURE CONTROL SOLENOID B
ELECTRICAL (SEC PRESSURE SOLENOID
VALVE) ....................................................................124
Description ............................................................124
CONSULT-II Reference Value ..............................124
On Board Diagnosis Logic ....................................124
Possible Cause .....................................................124
DTC Confirmation Procedure ...............................124
WITH CONSULT-II ............................................124
WITH GST .........................................................124
Wiring Diagram — CVT — SECPSV ....................125
Diagnostic Procedure ...........................................126
Component Inspection ..........................................128
PRESSURE CONTROL SOLENOID VALVE B
(SECONDARY PRESSURE SOLENOID VALVE)
.128
DTC P0840 TRANSMISSION FLUID PRESSURE
SENSOR A CIRCUIT (SEC PRESSURE SENSOR) .129
Description ............................................................129
CONSULT-II Reference Value ..............................129
On Board Diagnosis Logic ....................................129
Possible Cause .....................................................129
DTC Confirmation Procedure ...............................129
WITH CONSULT-II ............................................129
WITH GST .........................................................129
Wiring Diagram — CVT — SECPS ......................130
Diagnostic Procedure ...........................................131
DTC P0841 PRESSURE SENSOR FUNCTION .....134
Description ............................................................134
CONSULT-II Reference Value ..............................134
On Board Diagnosis Logic ....................................134
Possible Cause .....................................................134
DTC Confirmation Procedure ...............................134
WITH CONSULT-II ............................................134
Diagnostic Procedure ...........................................135
DTC P0845 TRANSMISSION FLUID PRESSURE
SENSOR B CIRCUIT (PRI PRESSURE SENSOR) .137
Description ............................................................137
CONSULT-II Reference Value ..............................137
On Board Diagnosis Logic ....................................137

CVT-6
INDEX FOR DTC
Revision: June 20062007 Versa
INDEX FOR DTCPFP:00024
Alphabetical Index UCS005XB
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTCs, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-68
.
*1: These numbers are prescribed by SAE J2012.
*2: Models without ABS does not indicate.
Items
(CONSULT-II screen terms) DTC
Reference page OBD-II Except OBD-II
CONSULT-II
GST*
1 CONSULT-II only
“TRANSMISSION”
A/T TCC S/V FNCTN P0744 P0744 CVT-110
ATF TEMP SEN/CIRC P0710 P0710CVT-85
BELT DAMG — P0730CVT-103
BRAKE SW/CIRC — P0703CVT-76
CAN COMM CIRCUIT U1000 U1000CVT-68
CONTROL UNIT(CAN) U1010 U1010CVT-71
CVT SPD SEN/FNCTN — P1723CVT-154
ENGINE SPEED SIG — P0725CVT-101
ELEC TH CONTROL — P1726CVT-156
ESTM VEH SPD SIG*2— P1722CVT-152
INPUT SPD SEN/CIRC P0715 P0715CVT-90
L/PRESS CONTROL — P1745CVT-163
L/PRESS SOL/CIRC P0745 P0745CVT-113
LU-SLCT SOL/CIRC P1740 P1740CVT-158
PNP SW/CIRC P0705 P0705CVT-78
PRESS SEN/FNCTN — P0841CVT-134
PRS CNT SOL/A FCTN P0746 P0746CVT-118
PRS CNT SOL/B CIRC P0778 P0778CVT-124
PRS CNT SOL/B FCTN P0776 P0776CVT-121
SEC/PRESS DOWN — P0868CVT-142
STARTER RELAY/CIRC — P0615CVT-72
STEP MOTR CIRC P1777 P1777CVT-164
STEP MOTR/FNC P1778 P1778CVT-168
TCC SOLENOID/CIRC P0740 P0740CVT-105
TCM-POWER SUPPLY — P1701CVT-145
TP SEN/CIRC A/T — P1705CVT-150
TR PRS SENS/A CIRC P0840 P0840CVT-129
TR PRS SENS/B CIRC P0845 P0845CVT-137
VEH SPD SEN/CIR AT P0720 P0720CVT-95

INDEX FOR DTC
CVT-7
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa
DTC No. Index UCS005XC
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTCs, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-68
.
*1: These numbers are prescribed by SAE J2012.
*2: Models without ABS does not indicate.
DTC
Items
(CONSULT-II screen terms)Reference page OBD-II Except OBD-II
CONSULT-II
GST*
1CONSULT-II only
“TRANSMISSION”
— P0615 STARTER RELAY/CIRCCVT-72
— P0703 BRAKE SW/CIRCCVT-76
P0705 P0705 PNP SW/CIRCCVT-78
P0710 P0710 ATF TEMP SEN/CIRCCVT-85
P0715 P0715 INPUT SPD SEN/CIRCCVT-90
P0720 P0720 VEH SPD SEN/CIR ATCVT-95
— P0725 ENGINE SPEED SIGCVT-101
— P0730 BELT DAMGCVT-103
P0740 P0740 TCC SOLENOID/CIRCCVT-105
P0744 P0744 A/T TCC S/V FNCTNCVT-110
P0745 P0745 L/PRESS SOL/CIRCCVT-113
P0746 P0746 PRS CNT SOL/A FCTNCVT-118
P0776 P0776 PRS CNT SOL/B FCTNCVT-121
P0778 P0778 PRS CNT SOL/B CIRCCVT-124
P0840 P0840 TR PRS SENS/A CIRCCVT-129
— P0841 PRESS SEN/FNCTNCVT-134
P0845 P0845 TR PRS SENS/B CIRCCVT-137
— P0868 SEC/PRESS DOWNCVT-142
— P1701 TCM-POWER SUPPLYCVT-145
— P1705 TP SEN/CIRC A/TCVT-150
— P1722
ESTM VEH SPD SIG*2CVT-152
— P1723 CVT SPD SEN/FNCTNCVT-154
— P1726 ELEC TH CONTROLCVT-156
P1740 P1740 LU-SLCT SOL/CIRCCVT-158
— P1745 L/PRESS CONTROLCVT-163
P1777 P1777 STEP MOTR CIRCCVT-164
P1778 P1778 STEP MOTR/FNCCVT-168
U1000 U1000 CAN COMM CIRCUITCVT-68
U1010 U1010 CONTROL UNIT(CAN)CVT-71

CVT-8
PRECAUTIONS
Revision: June 20062007 Versa
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
UCS005XD
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NIN G:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectUCS006Y0
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.

CVT SYSTEM
CVT-21
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa
CVT SYSTEMPFP:31036
Cross-sectional View - RE0F08AUCS005XQ
1. Converter housing 2. Oil pump 3. Forward clutch
4. Reverse brake 5. Planetary carrier 6. Primary pulley
7. Steel belt 8. Sun gear 9. Side cover
10. Internal gear 11. Secondary pulley 12. Differential case
13. Final gear 14. Idler gear 15. Reduction gear
16. Output gear 17. Parking gear 18. Input shaft
19. Torque converter
SCIA8015E