2006 NISSAN VERSA glove box

IP-1
INSTRUMENT PANEL
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION IP
A
B
IP
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions .............................................................. 2
PREPARATION ........................................................... 3
Special Service Tools ............................................... 3
Commercial Service Tools ........................................ 3
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 4
Work Flow ................................................................ 4
CUSTOMER INTERVIEW ..................................... 4
DUPLICATE THE NOISE AND TEST DRIVE ....... 5
CHECK RELATED SERVICE BULLETINS ........... 5
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 5
REPAIR THE CAUSE ........................................... 5
CONFIRM THE REPAIR ....................................... 6
Generic Squeak and Rattle Troubleshooting ........... 6
INSTRUMENT PANEL .......................................... 6
CENTER CONSOLE ............................................. 6
DOORS ................................................................. 6TRUNK .................................................................. 7
SUNROOF/HEADLINING ..................................... 7
OVERHEAD CONSOLE (FRONT AND REAR) ..... 7
SEATS ................................................................... 7
UNDERHOOD ....................................................... 7
Diagnostic Worksheet ............................................... 8
INSTRUMENT PANEL ASSEMBLY ......................... 10
Component Parts .................................................... 10
Removal and Installation ........................................ 11
WORK STEPS .................................................... 11
INSTRUMENT PANEL ASSEMBLY .................... 12
CLUSTER LID A .................................................. 16
CLUSTER LID C ................................................. 18
COMBINATION METER ...................................... 19
GLOVE BOX ASSEMBLY ................................... 21
INSTRUMENT LOWER FINISHER ..................... 21
CENTER CONSOLE ASSEMBLY ....................... 22
Disassembly and Assembly .................................... 24
GLOVE BOX ASSEMBLY ................................... 24
CENTER CONSOLE ASSEMBLY ....................... 25
COMBINATION METER ...................................... 25

INSTRUMENT PANEL ASSEMBLY
IP-11
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: June 20062007 Versa
Removal and InstallationEIS00979
WORK STEPS
When removing instrument panel & pad, cluster lid A, cluster lid C, passenger air bag module assembly and
center console assembly, follow steps in the order shown.
CAUTION:

Disconnect both battery cables.

Never tamper with or force air bag lid open, as this may adversely affect air bag performance.

Be careful not to scratch pad and other parts.
1. Instrument upper mask 2. Instrument upper panel assembly 3. Instrument side panel (LH)
4. Combination meter 5. Instrument finisher E 6. Cluster lid A
7. Instrument side mask (LH) 8. Instrument panel & pad 9. Side ventilator assembly (LH)
10. Instrument side finisher 11. Instrument lower finisher 12. Steering column cover upper
13. Fuse block lid 14. Steering column cover lower 15. Steering lock escutcheon
16. Instrument lower cover (LH) 17. Console rear finisher (with armrest) 18. Console body assembly (with arm-
rest)
19. Center console 20. Console mask cover (with armrest) 21. Console mask
22. A/T console finisher / M/T console
boot / CVT console finisher23. Console rear finisher (without armrest) 24. Console body assembly (without
armrest)
25. Rear cup holder (without armrest) 26. Instrument lower cover (RH) 27. Instrument finisher D
28. Controller 29. Cluster lid C 30. Audio unit
31. Glove box assembly 32. Side ventilator assembly (RH) 33. Instrument side mask (RH)
34. Passenger air bag module assem-
bly35. Instrument side panel (RH) Pawl
Clip Metal clip
PartsReference
pageInstrument
panel and padCluster lid A Cluster lid C Passenger air
bag module
assemblyCenter
console
assembly
Instrument finisher EIP-12
[ 1 ] [ 1 ] [ 1 ]
Cluster lid CIP-18
[ 2 ] [ 2 ]
Audio unitAV-4 3
[ 3 ]
Front pillar garnish (LH/RH)EI-32
[ 4 ] [ 2 ] [ 1 ]
Instrument side panel (LH/RH)IP-10
[ 5 ] [ 3 ] [ 2 ]
Instrument side mask (LH/RH)IP-10
[ 6 ] [ 4 ] [ 3 ]
Instrument side finisherIP-10
[ 7 ] [ 5 ]
Side ventilator assembly (LH)IP-10
[ 8 ] [ 6 ]
Steering lock escutcheonIP-10
[ 9 ]
Steering column cover upperIP-10
[ 10 ] [ 7 ]
Steering column cover lowerIP-10
[ 11 ]
Cluster lid AIP-16
[ 12 ] [ 8 ]
Combination meterDI-23
[ 13 ]
Instrument lower finisherIP-21
[ 14 ]
Glove box assemblyIP-21
[ 15 ]
Side ventilator assembly (RH)IP-10
[ 16 ] [ 4 ]
Passenger air bag module assemblySRS-46
[ 17 ] [ 5 ]
Instrument upper maskIP-10
[ 18 ]
Instrument finisher DIP-10
[ 19 ]
Controller MTC-61
[ 20 ]
Instrument upper panel assembly IP-10
[ 21 ]

IP-14
INSTRUMENT PANEL ASSEMBLY
Revision: June 20062007 Versa
9. Remove steering lock escutcheon.
10. Remove screws, and disengage pawls then remove the steering column cover.
11. Remove cluster lid A.
a. Remove screws from instrument upper panel right side.
b. Lift the instrument upper panel up, disengage metal clips.
c. Pull backward and disengage clips.
d. Remove cluster lid A.
12. Remove combination meter. Refer to DI-23, "
Removal and Installation" .
13. Remove instrument lower finisher.
a. Disengage pawls and remove fuse block lid.
b. Remove the screws.
c. Pull backward while disengaging the instrument lower finisher
clip and pawls.
d. Disconnect in-vehicle sensor and harness connector, and then
remove instrument lower finisher.
14. Remove glove box. Refer toIP-24, "
GLOVE BOX ASSEMBLY" .
15. Remove side ventilator assembly.
a. Insert a suitable tool into the side ventilator assembly from cen-
ter console side, disengage the clips and pawl of instrument
panel pad.
PIIB3969E
PIIB2880E
LIIA2544E
PIIB3977E

INSTRUMENT PANEL ASSEMBLY
IP-15
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: June 20062007 Versa
b. Reach through the glove box compartment by hand to the back-
side of the side ventilator and push against A as shown to
engage the pawl.
c. Insert a suitable tool into the bottom gap of side ventilator
assembly after removing the instrument side mask and push
against B as shown to disengage the pawl.
d. Lift the side ventilator assembly up from the bottom, pull back-
ward while disengaging the side ventilator assembly upper
pawls, and then remove the side ventilator assembly.
16. Remove front passenger air bag module. Refer to SRS-46, "
FRONT PASSENGER AIR BAG MODULE" .
17. Remove instrument upper mask.
a. Insert a remover into backside space of instrument upper mask.
b. Disconnect harness connector, and then remove instrument
upper mask.
18. Remove instrument finisher D.
a. Insert a remover into upper space of instrument finisher D.
b. Disengage clips and pawls, then remove instrument finisher D.
19. Remove controller. Refer to MTC-61, "
CONTROLLER" .
PIIB6385E
PIIB3979E
PIIB2445E
PIIB2446E

INSTRUMENT PANEL ASSEMBLY
IP-21
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: June 20062007 Versa
17. Remove screws (A) and metal clip (B), and remove combination
meter.
Installation
Installation is in the reverse order of removal.
GLOVE BOX ASSEMBLY
Removal
1. Remove glove box screws.
2. Pull backward while disengaging the glove box assembly pawls.
3. Disconnect lamp harness connector, and then remove glove box
assembly.
Installation
Installation is in the reverse order of removal.
INSTRUMENT LOWER FINISHER
Removal
1. Pull backward while disengage the instrument lower finisher's
clip and pawls.
2. Disconnect in-vehicle sensor and harness connector, and then
remove instrument lower finisher.
Installation
Installation is in the reverse order of removal.
PKIC0703E
PIIB3404E
LIIA2544E

IP-24
INSTRUMENT PANEL ASSEMBLY
Revision: June 20062007 Versa
Disassembly and AssemblyEIS0097A
GLOVE BOX ASSEMBLY
Disassembly
1. Remove screws of damper, and then remove damper.
2. Remove screws of glove box striker, and then remove glove box striker.
3. Remove screws of glove box latch, and then remove glove box latch.
Assembly
Assembly is in the reverse order of disassembly.
1. Glove box striker 2. Glove box 3. Glove box latch
4. Damper
LIIA2555E

LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa CONSULT-II Function (IPDM E/R) ......................... 81
Parking, License Plate and Tail Lamps Do Not Illu-
minate .................................................................... 81
Parking, License Plate and Tail Lamps Do Not Turn
OFF (After Approx. 10 Minutes) ............................. 85
Bulb Replacement .................................................. 86
PARKING LAMP ................................................. 86
LICENSE PLATE LAMP ...................................... 86
TAIL LAMP .......................................................... 86
Removal and Installation ........................................ 86
PARKING LAMP ................................................. 86
LICENSE PLATE LAMP ...................................... 86
TAIL LAMP .......................................................... 86
REAR COMBINATION LAMP .................................. 87
Components ........................................................... 87
Bulb Replacement .................................................. 87
Removal and Installation ........................................ 87
REMOVAL ........................................................... 87
INSTALLATION ................................................... 87
Disaassembly and Assembly ................................. 87
DISSASEMBLY ................................................... 87
ASSEMBLY ......................................................... 88
INTERIOR LAMP ...................................................... 89
Map lamp ............................................................... 89
BULB REPLACEMENT ....................................... 89
REMOVAL AND INSTALLATION ........................ 89
DISASSEMBLY AND ASSEMBLY ...................... 89
Luggage Compartment Lamp ................................ 90
BULB REPLACEMENT ....................................... 90
REMOVAL AND INSTALLATION ........................ 90
INTERIOR ROOM LAMP .......................................... 91
Component Parts and Harness Connector Location ... 91
System Description ................................................ 91
POWER SUPPLY AND GROUND ...................... 91
SWITCH OPERATION ........................................ 92
INTERIOR ROOM LAMP TIMER OPERATION ... 93
INTERIOR LAMP BATTERY SAVER CONTROL ... 94Schematic ............................................................... 95
Wiring Diagram — INT/L — .................................... 96
Terminals and Reference Values for BCM ............101
How to Proceed With Trouble Diagnosis ..............101
Preliminary Check ................................................101
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................101
CONSULT-II Function (BCM) ...............................101
CONSULT-II START PROCEDURE ..................101
WORK SUPPORT .............................................101
DATA MONITOR ...............................................101
ACTIVE TEST ...................................................102
WORK SUPPORT .............................................102
DATA MONITOR ...............................................102
Interior Room Lamp Control Does Not Operate
(With Map Lamp) ..................................................103
Interior Room Lamp Control Does Not Operate
(Without Map Lamp) .............................................105
Bulb Replacement ................................................107
ROOM LAMP ....................................................107
Removal and Installation ......................................107
ROOM LAMP ....................................................107
ILLUMINATION .......................................................108
System Description ...............................................108
ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................108
EXTERIOR LAMP BATTERY SAVER CONTROL .109
CAN Communication System Description ............109
Schematic .............................................................110
Wiring Diagram — ILL — .......................................111
Bulb Replacement ................................................115
GLOVE BOX LAMP ...........................................115
BULB SPECIFICATIONS ........................................116
Headlamp .............................................................116
Exterior Lamp .......................................................116
Interior Lamp/Illumination .....................................116

HEADLAMP (FOR USA)
LT-5
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
HEADLAMP (FOR USA)PFP:26010
Component Parts and Harness Connector LocationEKS00HVB
System DescriptionEKS00HVC
Headlamp operation is controlled by the BCM (body control module) based on inputs from the combination
switch (lighting switch). When the lighting switch is placed in the 2ND position, the BCM receives an input sig-
nal requesting the headlamps (and tail lamps) illuminate. The BCM sends a signal, via the CAN communica-
tion lines, to the IPDM E/R (intelligent power distribution module engine room) requesting the headlamps be
turned ON. The CPU (central processing unit) located in the IPDM E/R controls ground for the headlamp high
and headlamp low relay coils. These relays direct power to the respective headlamps, which then illuminate.
OUTLINE
Power is supplied at all times

to headlamp high relay RH and LH (located in IPDM E/R),

to headlamp low relay (located in IPDM E/R),

to ignition relay (located in IPDM E/R),

through 15A fuse (No. 52, located in IPDM E/R) and

through 20A fuse (No. 53, located in IPDM E/R)

to CPU located in IPDM E/R,

through 40A fusible link (letter g , located in fuse and fusible link block)

to BCM terminal 70,

through 10A fuse [No. 8, located in fuse block (J/B)]

to BCM terminal 57, and

through 10A fuse [No. 13, located in fuse block (J/B)]

to combination meter terminal 27.
With the ignition switch in the ON or START position, power is supplied

to the ignition relay (located in IPDM E/R),

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 3, located in fuse block (J/B)]

to combination meter terminal 28.
1. IPDM E/R E46, E47 and E48 2. BCM M18 and M20 (view with glove
box removed)3. Combination switch (lighting switch)
M28
4. Combination meter M24
WKIA5469E