2006 NISSAN VERSA ad blue

AV-60
TELEPHONE
Revision: June 20062007 Versa
Voice Activated Control Function Does Not OperateEKS00IBA
NOTE:
Even under the normal condition, Bluetooth voice guidance may not occur when pressing steering wheel
audio control switch.
BLUETOOTH VOICE GUIDANCE IS HEARD WHEN PRESSING STEERING WHEEL AUDIO
CONTROL SWITCH
1. CHECK HARNESS BETWEEN BLUETOOTH CONTROL UNIT AND BLUETOOTH MICROPHONE
1. Turn ignition switch OFF.
2. Disconnect Bluetooth control unit connector and Bluetooth microphone connector.
3. Check continuity between Bluetooth control unit connector B121
(A) and Bluetooth microphone connector R15 (B).
4. Check continuity between Bluetooth control unit harness con-
nector B121 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK BLUETOOTH MICROPHONE POWER SUPPLY
1. Connect Bluetooth control unit connector and Bluetooth microphone connector.
2. Turn ignition switch ON.
3. Check voltage between Bluetooth microphone connector R15
terminal 5 and ground.
YES or NO
YES >> GO TO 3.
NO >> Replace Bluetooth control unit. Refer to AV- 6 3 , "
BLUE-
TOOTH CONTROL UNIT" .
Terminals
Continuity
Connector Terminal Connector Terminal
A: B1216
B: R156
Ye s 78
87
29 5
Te r m i n a l s
Continuity
Connector Terminal —
A: B1217
Ground No 8
29
LKIA0778E
5 - Ground : Approx. 5 V
LKIA0779E

TELEPHONE
AV-61
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: June 20062007 Versa
3. CHECK MIC. SIGNAL
1. Check signal between Bluetooth control unit harness connector
B121 terminals 7 and 8.
OK or NG
OK >> Replace Bluetooth control unit. Refer to AV- 6 3 , "BLUETOOTH CONTROL UNIT" .
NG >> Replace Bluetooth microphone. Refer to AV-65, "
BLUETOOTH MICROPHONE" .
BLUETOOTH VOICE GUIDANCE IS NOT HEARD WHEN PRESSING STEERING WHEEL AUDIO
CONTROL SWITCH
1. CHECK STEERING WHEEL AUDIO CONTROL SWITCH CIRCUIT
Refer to AV-30, "
Steering Switch Check (With Bluetooth)" .
OK or NG
OK >> GO TO 2.
NG >> Replace applicable parts.
2. CHECK BLUETOOTH VOICE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect Bluetooth control unit connector and audio unit connector.
3. Check continuity between Bluetooth control unit harness con-
nector B121 (A) and audio unit harness connector M44 (B).
4. Check continuity between Bluetooth control unit harness con-
nector B121 (A) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.7 – 8:When giving a voice
LKIA0780EPKIB5037J
Te r m i n a l s
Continuity
Connector Terminal Connector Terminal
A: B1219
B: M4431
Ye s 10 33
11 2 7
Te r m i n a l s
Continuity
Connector Terminal —
A: B1219
Ground No 10
11
LKIA0781E

AV-62
TELEPHONE
Revision: June 20062007 Versa
3. CHECK MUTE SIGNAL
1. Connect Bluetooth control unit connector and audio unit connector.
2. Turn ignition switch ON.
3. Check voltage between Bluetooth control unit connector B121
terminal 11 and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace audio unit. Refer toAV- 4 3 , "
AUDIO UNIT" .
4. CHECK BLUETOOTH VOICE SIGNAL
1. Check signal between Bluetooth control unit harness connector
B121 terminals 9 and 10.
OK or NG
OK >> Replace audio unit. Refer to AV- 4 3 , "AUDIO UNIT" .
NG >> Replace Bluetooth control unit. Refer to AV-63, "
BLUETOOTH CONTROL UNIT" . 11 - Ground : Approx. 5 V
LKIA0782E
9 – 10:When giving a voice
LKIA0783ESKIB3609E

TELEPHONE
AV-63
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: June 20062007 Versa
Removal and InstallationEKS00I9M
BLUETOOTH CONTROL UNIT
Removal
1. Remove luggage side lower finish (RH). Refer to EI-42, "Removal and Installation" .
2. Disconnect Bluetooth antenna harness clip.
3. Disconnect Bluetooth antenna harness connector.
4. Disconnect Bluetooth control unit harness connector.
5. Remove Bluetooth control unit upper and lower bracket bolts.
6. Unhook the Bluetooth control unit upper and lower brackets and remove Bluetooth control unit.
7. Remove Bluetooth control unit bracket screws and remove the upper and lower brackets from unit.
Installation
Installation is in the reverse order of removal.
1. Bluetooth control unit bracket 2. Bluetooth control unit A. Bolt
B. Harness clip C. Bluetooth antenna harness connector D. Bluetooth control unit connector
E. screw⇐Front
LKIA0762E

AV-64
TELEPHONE
Revision: June 20062007 Versa
BLUETOOTH ANTENNA
Removal
1. Remove luggage side lower finisher (RH). Refer to EI-42, "Removal and Installation" .
2. Disconnect the Bluetooth harness clips.
3. Disconnect the Bluetooth antenna connector.
4. Remove the Bluetooth antenna bolt and remove antenna.
5. Remove screws and remove bracket.
Installation
Installation is in the reverse order of removal.
1. Bluetooth antenna bracket 2. Bluetooth antenna A. Bolt
B. Screws C. Harness clips
LKIA0763E

TELEPHONE
AV-65
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: June 20062007 Versa
BLUETOOTH MICROPHONE
Removal
1. Remove over-head console assembly, roof finisher. Refer to EI-39, "HEADLINING" .
2. Remove the Bluetooth microphone.
Installation
Installation is in the reverse order of removal.

BL-112
INTELLIGENT KEY SYSTEM
Revision: June 20062007 Versa
ACTIVE TEST
Test item Description
DOOR LOCK/UNLOCKThis test is able to check door lock/unlock operation.

The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-II screen is touched.

The all door lock actuators are locked when “LOCK” on CONSULT-II screen is touched.
ANTENNAThis test is able to check Intelligent Key antenna operation.
When the following conditions are met, hazard warning lamps flash.

Inside key antenna (front console) detects Intelligent Key, when “ROOM ANT1” on CONSULT-
II screen is touched.

Inside key antenna (instrument panel and rear floor) detects Intelligent Key, when “ROOM
ANT2” on CONSULT-II screen is touched.

Outside key antenna (driver side) detects Intelligent Key, when “DRIVER ANT” on CONSULT-II
screen is touched.

Outside key antenna (passenger side) detects Intelligent Key, when “ASSIST ANT” on CON-
SULT-II screen is touched.

Outside key antenna (rear bumper) detects Intelligent Key, when “BK DOOR ANT” on CON-
SULT-II screen is touched.
OUTSIDE BUZZER
(DRIVER DOOR)This test is able to check Intelligent Key warning buzzer operation.
Intelligent Key warning buzzer sounds when “ON” on CONSULT-II screen is touched.
INSIDE BUZZER
(CHIME)This test is able to check Intelligent Key warning chime (Instrument panel) operation.

Take away warning chime sounds when “TAKE OUT” on CONSULT-II screen is touched.

Ignition switch warning chime sounds when “KNOB” on CONSULT-II screen is touched.

Ignition key warning chime sounds when “KEY” on CONSULT-II screen is touched.
INDICATORThis test is able to check warning lamp operation.

“KEY” Warning lamp (Green) illuminates when “BLUE ON” on CONSULT-II screen is touched.

“KEY” Warning lamp (Red) illuminates when “RED ON” on CONSULT-II screen is touched.

“LOCK” Warning lamp illuminates when “KNOB ON” on CONSULT-II screen is touched.

“KEY” Warning lamp (Green) flashes when “BLUE IND” on CONSULT-II screen is touched.

“KEY” Warning lamp (RED) flashes when “BLUE IND” on CONSULT-II screen is touched.

“P-SHIFT” Warning lamp flashes when “KNOB ON” on CONSULT-II screen is touched.

BL-156
INTELLIGENT KEY SYSTEM
Revision: June 20062007 Versa
“KEY” Warning Lamp (GREEN) CheckEIS009DE
1. CHECK WARNING LAMP OPERATION
With CONSULT-II

Check “INDICATOR” in “ACTIVE TEST” mode with CONSULT-
II.

Select “BLUE ON”.
“KEY” warning lamp (green) should illuminate.
Without CONSULT-II
1. Turn ignition switch OFF.
2. Ensure Intelligent Key is in your possession inside the vehicle.
3. While monitoring the combination meter warning lamps, push
the ignition knob switch.
4. The "KEY" warning lamp (green) should illuminate indicating
that the Intelligent Key is nearby.
OK or NG
OK >> INSPECTION END
NG >> Check combination meter. Refer to DI-5, "
COMBINATION METERS" .
Check Warning Chime in Combination MeterEIS0092R
1. CHECK WARNING CHIME OPERATION
With CONSULT-II

Check “INSIDE BUZZER” in “ACTIVE TEST” mode with CON-
SULT-II.

Touch “TAKE OUT”, “KNOB” and “KEY” on “ACTIVE TEST”
screen.
OK or NG
OK >> INSPECTION END
NG >> GO TO 2.
PIIB4356E
WIIA1264E
Does each warning chime sound?
PIIB6619E