2006 MITSUBISHI COLT door lock

DOOR
BODY42-16
CONSTRUCTION DIAGRAM
AC206478AB

Door window glass Door window glass
Power window motor
Power window glass
regulator assembly
Power window glass
regulator assembly
Power window motor
Power window switch (driver's side) Power window
switch
Power window
lock switch
DESCRIPTION OF STRUCTURE AND
OPERA
T ION
POWE R W I NDOW SWITCH
•The power wind ow switch employs t he push-pull
ope
ration meth od to imp r ove safety . T o o pen a
doo
r windo w glass, p r ess in the switch kno b , and
to close, pu
ll it up.
•The one-to uch mechanism is a dopted to the
driver's power win
dow swit ch to fully op en
driver
’ s door win dow gla s s in a sin g le o peration.
POWER WI NDOW TIMER FUNCTION
The po wer wind ow has a t i me r function which allows
the wind
ow glass t o be closed or o pened for 30 sec
-
onds after the ignition switch is turned OFF . (Durin g
the timer o
peration, if the driver's doo r or fron t p a s
-
senger's d oor is open ed, th e timer is expired at the
moment.)
POWER WI NDOW LOCK SWITCH
The driver's door power wind ow switch is equ ipped
with the
lock switch. This swit ch inhib i t s the open
-
ing/ clos ing ope ra tio n o f t h e do or wind ow gl ass b y t he
f
r ont p a ssenger's power window switch or rear power
window switche
s .

TECHNICAL FEATURES
GENERAL00-27
POWER WINDOW WITH SAFETY MECHA-
NISM
The power window with safety mechanism has been
adopted to automatically roll down and stop the door
window glass as soon as the occurrence of jamming
is detected at the time of rolling up the door window
glass.
SUNROOF WITH SA FETY MECHANISM
The sunroof with safe ty mechanism has been
adopted so that the roof lid glass can move in the
reverse direction and stop when application of exter
-
nal force hinders the movement during the sliding to
close or tilt down operation.
TRIMS AND HEADLINING
The head impact absorption structure has been
adopted for the pillar trim, quarter trim, and headlin
-
ing so that impact towards the head of a passenger
can be reduced.
OTHER SAFETY FEATURES
•3-point ELR seat belts
•Child-protection rear door locks
•Front fog lamps
EQUIPMENTSM2000026000221
IMMOBILIZER SYSTEM
AC306415AC
M.U.T.-III
Ignition
key ring
antenna
Immobilizer-
ECU
Ignition key
Encrypted
code
Transponder Power
(Wireless)
Encrypted code
(Wireless) Control
signal
Engine-
CVT-ECU
All models are equipped with the e ngine immobilizer
system as st andard. The en gine immobilizer syst em
preve nts the engin e from starting and immobilizes
the vehicle if a key o ther tha n the key registered for
that vehicle is used in an attempt to start the e ngine
af te r forced entry . The en gine immobilizer syst em
consist s of the ignition key, key ring antenna, immo
-
bilizer-ECU, and engine-CVT-ECU.

TECHNICAL FEATURES
GENERAL00-28
ENVIRONMENTAL PROTECTION
M2000027000279
Mitsubishi has given careful consideration to protec-
tion of natural resources and the environment in the
vehicle. Environmentally friendly features are shown
below.
IMPROVEMENT ON RECYCLING EFFICIENCY
ClassificationMain Components
Components made
of recycled
materialsChip materials produced during manufacturing process has been reused as the
following components: Door inside handle, bu mper, radiator grille, instrument panel,
door trims, or floor padding.
Waste materials produced by other i ndustries have been reused as the following
components: Engine oil level gauge, air filter casing, and sound absorbing materials
for dash panel
Components made
of materials which
can be easily
recycledThermoplastic resin has been utilised as the following components: Inside door
handle, bumper, radiator grille, instrument panel, door trim
Thermoplastic resin has been utilised as t he following components: Vacuum hose for
engine control, air intake hose, hood weather strip, tailgate opening weather strip
REDUCTION OF MATERIAL BURDEN ON ENVIRONMENT
ItemMain Components
Elimination of
environmental
burden materialsLead-free materials have been utilised as the following components: Radiator, fuel
tank, power steering oil pressure hose, el ectrodeposition paint for body, glass ceramic
print, heater core, battery terminals, wiring harness
Non-asbestos material has been used for engine gaskets.
PVC(polyvinyl chloride)-free materials ha ve been used for the waterproofing film.
Prevention of
ozone depletionAir conditioner filled with new refrigerant (HFC 134a) has been installed.
Prevention of air
pollutionEmployment of a metal cylinder head gasket reduces the volume of incomplete
combustion generated between the cylinder block and cylinder head, and suppresses
the level of unburned hydrocarbon (HC).
SERVICEABILITY AND RELIABILITY
M2000028000528
MULTI USE TESTER-III (M.U.T.-III) SUB
ASSEMBLY
Comprehensive improvements have been made to
the M.U.T.-II, a tester for diagnosing problems with
the electronic control system. For easier servicing,
the newly developed M.U.T.-III has greatly improved
functions and is much easier to use. The M.U.T.-III
expands the functions of the M.U.T.-II in the following
ways:
1.CAN* bus diagnosis
•Auto diagnosis function for the CAN commu-
nications bus line is added.
NOTE: *CAN: Controller Area Network (for further
details, refer to GROUP 54C
P.54C-2).

DIAGNOSTIC FUNCTION
SMART WIRING SYSTEM (SWS)54B-8
DIAGNOSTIC FUNCTION
M2541003000642
DIAGNOSIS CODE SET
For more information about diagnosis code output,
refer to the Workshop Manual.
SWS INPUT SIGNAL CHECK USING
M.U.T.-III
When the M.U.T.-III is connected to the diagnosis
connector and any of the SWS-linked switches is
operated, the PC buzzer sounds to evaluate whether
the switch is normal or not.
SWS INPUT SIGNAL CHECK AND ECU
CHECK BY USING SWS MONITOR
The switch signals sent by ECUs and the operations
of these ECUs can be confirmed by using the SWS
monitor and the M.U.T.-III.
INPUT SIGNALS THAT CAN BE CHECKED
Input signalCondition for sounding buzzerDisplay on
M.U.T.-III (when
SWS monitor is
used)
Ignition switch (ACC)Turn from "LOCK" (OFF) to "ACC" positionfrom OFF to ON
Ignition switch (IG1)Turn from "ACC" to "ON" positionfrom OFF to ON
Key reminder switchRemove the ignition key from ignition key cylinder
(form inserted position)from OFF to ON
Hazard lamp switchTurn from OFF to ONfrom OFF to ON
Fog lamp switch
Remote controlled mirror
switch (unfolding/folding
switch)
Speed signal When the speed changes from less than 10 km/h to
more than 10 km/hDisplays the
vehicle speed
Cranking signalWhile the ignition switch is in START position (while
cranking the engine)−
Selector lever P position signal
(parking)When the selector lever is shifted to the "P" position
(Ignition switch: ON or START)−
Selector lever R position signal
(reverse)When the selector lever is shifted to the "R" position
(Ignition switch: ON or START)−
Buzzer triggered by
ETACS-ECU
*1
When the following conditions are satisfied
•Ignition switch: LOCK (OFF) position
•Lighting switch: ON
•Driver’s door switch: ON (Driver’s door: OPEN)
ON
When requirements for sounding each warning buzzer
are not satisfiedOFF
Door switchDriver’s doorWhen door(s) or tailgate is opened from the closed
positionfrom OFF to ON
Passenger’s
door
Rear door
All door switchA door is opened when all the doors are closedfrom OFF to ON

DIAGNOSTIC FUNCTION
SMART WIRING SYSTEM (SWS)54B-9
Driver's door lock actuator
switchMove the door lock knob or driver’s door key cylinder
from lock position to unlock position or vice versafrom ON to OFF or
from OFF to ON
Driver's door unlock actuator
switchfrom OFF to ON or
from ON to OFF
Power window timer duration*1When the power window timer is activatedDisplays the
operation duration
Column
switchTail lamp switchWhen the lighting switch is turned from one position to
the tail lamp positionfrom OFF to ON
Headlamp
switchWhen the lighting switch is turned from one position to
the headlamp position
Dimmer switchWhen the switch is turned from the OFF to the ON
position
Passing switch
Turn signal
lamp LH switch
Turn signal
lamp RH switch
Headlamp specification*1The display alters according to the headlamp
specification ("4 BULBS" or "2 BULBS").4 BULBS
Column
switch (wiper
switch)Windshield
mist wiper
switchWhen the switch is turned from OFF to ONfrom OFF to ON
Windshield
intermittent
wiper switch
Windshield low
speed wiper
switch
Windshield
high speed
wiper switch
Windshield
washer switch
Rear wiper
switch
Rear washer
switch
Windshield
intermittent
wiper volumeWhen the interval adjusting knob is turned from
"FAST" to "SLOW" while the ignition switch is ON.Displays the
windshield
intermittent wiper
volume voltage
Wiper
autostop
signalFrontWhen activated from the stopped conditionfrom OFF to ON
Rear
Input signal Condition for sounding buzzer Display on
M.U.T.-III (when
SWS monitor is
used)

ECU FUNCTIONS AND CONTROLS IN THE SWS
SMART WIRING SYSTEM (SWS)54B-11
ECU FUNCTIONS AND CONTROLS IN THE SWS
M2541004000805
Following functions are controlled by ECUs of SWS.
FunctionControl ECUFunction
description
BuzzerLamp reminder buzzer functionETACS-ECU, Column switchP.54B-12
Door-ajar warning buzzer functionETACS-ECUP.54B-12
Turn-signal lamp operation sound
functionETACS-ECU, Column switchP.54B-13
Central door
locking systemCentral door locking control functionETACS-ECUP.54B-13
Shift "P" position linked door unlock
function P.54B-13
Power windowPower window timer functionETACS-ECUP.54B-14
Keyless entry
systemMulti-mode keyless entry system ETACS-ECUP.54B-14
Keyless entry hazard answerback
functionETACS-ECUP.54B-14
Keyless entry room lamp answerback
functionETACS-ECUP.54B-15
Windshield
wiper and
washerIntermittent control speed-dependent variable type>ETACS-ECU, Column switchP.54B-16
Mist wiper controlP.54B-16
Low speed wiper and high speed wiper
controlP.54B-17
Windshield wiper linked with washer
functionP.54B-18
Rear wiper and
washerRear wiper controlETACS-ECU, Column switchP.54B-19
Rear wiper linked with washer functionP.54B-20
Electric
retractable
remote
controlled
mirrorElectric retractable remote controlled
mirror timer functionETACS-ECUP.54B-20
Automatic unfolding functionP.54B-21
Flasher timer
functionTurn-signal lampETACS-ECU, Column switchP.54B-21
Hazard lampP.54B-22
Turn-signal lamp indicatorP.54B-22
HeadlampHigh-beam indicatorETACS-ECU, Column switchP.54B-22
Fog lampFog lamp controlETACS-ECU, Column switchP.54B-22
Fog lamp indicatorP.54B-22

ECU FUNCTIONS AND CONTROLS IN THE SWS
SMART WIRING SYSTEM (SWS)54B-13
TURN-SIGNAL LAMP OPERATION SOUND FUNCTION (T HE INITIAL CONDITION:
WITHOUT FUNCTION)
AC206262AB
Turn signal
lamp switch

(RH) OFFON
Turn signal
lamp (RH)
OFFON
OFF ON
Turn signal
lamp (LH) Turn signal
lamp switch
(LH) OFFON
Hazard lamp
switch OFFON
Hazard lamp OFFON
ON (Buzzer sounds)
OFF (Buzzer
does not sound)
Buzzer
output
ET
ACS-ECU buzzer soun ds simult an eously with the
blin
ks of the turn-signal lamp an d the h a zard lamp.
NOTE: Av ailability of the turn-signal lamp op eratio n
tone fu
nction can be sele cted by th e cu stomize func
-
tion (Refer to P.54B- 25).
CENTRAL DOOR LOCKING SYSTEM
CENTRAL DOOR LOCKING CONTROL
FUNCTION
AC101496
AC
t
t
ON
OFF ON
OFF ON
OFF
ON
OFF
t: 0.25 second
Lock switch
Lock relay output
Unlock relay output Unlock switch
When th e front doors are locked (when the lock
switch turns ON a
f te r turning OFF the u n lock switch
in the driver's door lo
ck a c tuat or), ET ACS-ECU turn s
ON the
lock relay o u tput fo r 0.25 second, a nd lo cks
all
doors (including th e t a ilg ate).
When the front doors is unlo cke d (when th e unlock
switch turns ON
af ter turn ing OFF t he lock switch on
the driver's door
lock actuator ), ET ACS-ECU tu rns
ON the
unlock re lay outpu t for 0.2 5 se cond , and
unlocks all doors (in
c lu ding the t a ilgate).
SH IFT "P " POS I TIO N LIN K ED DOO R
UNLOCK FUNCTION (THE INITIAL
CONDITION: WITH FUNCTION)
AC208135AB
t
T
ON
OFF ON
OFF
Inhibiter switch "P"
Unlock relay output
t: 0.25 second
T: 0.3 second
When the se lector lever is shif ted to "P" position
(p
a r kin g ) (inh ibit or swit ch "P" is ON) with the ignition
switch turne
d to th e ON po sit i on, t he ET ACS-ECU
turns
on the u n lock re lay output for 0.25 second (0. 3
second af
ter the selector le ver o peration) an d
unlocks all the d
oors (including the t a ilga t e).
NOTE: Using a cust omisation fun c tio n , this fu nction
can b
e
ena bled or disabled. For more informatio n
about t
he customisatio n function , refer to
P.54B-25.

ECU FUNCTIONS AND CONTROLS IN THE SWS
SMART WIRING SYSTEM (SWS)54B-14
POWER WINDOW
POWER WINDOW TIMER FUNCTION
AC309963
Ignition switch (IG1)ON
(Open)ON
ON tt
OFF
t:30 seconds
(Close)OFF
OFF
Driver's door and
passenger's switch
Power window relay
AB
When the power window relay is turn ed ON with the
ignition
switch ON, t he power window relay is kept
ON for 3
0 seconds even af ter th e ign i tio n swit ch is
turned OFF
, enab ling the do or windo w to be o pened
and closed with
the po we r window switch .
If the dr ive r's or t he fron t p a ssenger d oor is ope ned
during
timer ope ration , the p o we r windo w re lay is
turned OFF a
t the same time.
KEYLESS ENTR Y SYSTEM
MU L T I-MODE KEYLESS ENT R Y SYST EM
The door mirrors can b e opera t ed by the keyless
entry transmitte
r opera t ion.
For the operation, re fer to Group 42 − Body − Key-
less ent ry s yste m P.42-13.
KEYLESS ENTR Y HAZARD
ANSW
ERBACK FUNCTION (INITIAL
SETTING:
LOCK, FLASH ONCE,
UNLOCK, FLASH TW
ICE)
AC209072AG
ON
OFF OFF
ON
OFF
LOCK
UNLOCK
Illuminate
Extinguish
Keyless entry
transmitter
Lock relay output
Unlock relay output
Hazard lamp
The ha
zard a n swer b a ck function that allows check-
ing the lock/u nlock st a t e of t he doo r easily eve n in
the daytime is in
st alled. Whe n the lock signal from
the keyless entry transmitter is received in
to
ET
ACS-ECU, all do ors (includin g the t a ilgat e) are
LOCK, an
d the tu rn signal lamp blinks once. Wh en
the unlock signal is rece
ive d , all doors (in c lu ding the
t
a ilgat e) are UNLOCK, and the turn-signa l la mp
blin
ks twi c e.
NOTE: The answer back blink time can be ad just ed
by th
e customise function (Re f er to
P.54B-25).