2006 MITSUBISHI COLT air condition

A/C-ECU
HEATER, AIR CONDITIONER AND VENTILATION55-9
COMMUNICATION
The A/C receives the following kinds of signals
through CAN communication.
SignalTransmitter ECU
Engine coolant
temperature signalEngine-CVT-ECU
or Engine-ECU
NOTE: . For further details on CAN, refer to GROUP
54C, CAN
P.54C-2.
DIAGNOSTIC FUNCTION
Code No.Diagnostic itemService data display
contents when
diagnosis code is set
B1011Ambient temperature sensor system (short circuit)20°C
B1012Ambient temperature sensor system (open circuit)
B1021Air thermo sensor system (short circuit)−6°C
B1022Air thermo sensor system (open circuit)
B1082Automatic/manual types abnormal error−
U1073Bus off error−
U1100Engine-CVT-ECU time-out
U1101
U1102ABS-ECU time-out
U1106EPS-ECU time-out
U1109ETACS-ECU time-out
U1120Failure information on engine-CVT-ECU (related to engine)
U1206Flag invalid

A/C-ECU
HEATER, AIR CONDITIONER AND VENTILATION55-10
SERVICE DATA OUTPUT
Item No.Check items
02Ambient temperature sensor
03Air thermo sensor
04A/C pressure sensor
05Water temperature sensor
07Set temperature
08Set temperature (control part set value)
15Outside/Inside air selection damper
20Blower motor
21Blower motor (Target)
30A/C switch
31A/C switch (control part set value)
35Rear window defogger switch (control part set value)
36Blower switch
37Outside/Inside air selection switch
40Abnormal low pressure judgement
41Refrigerant leaks judgement
42DEF position flag
43Forcible DEF position flag
44Forcible DEF DRY flag
ACTUATOR TEST
Item No.Check items
30Outside/Inside air selection damper control motor
31
40Rear defogger switch
41
09Condenser fan
0B
50Idle-up requirement
51
52

DUCTS
HEATER, AIR CONDITIONER AND VENTILATION55-11
DUCTS
M2551001300110
AC313959AB
To windshield (Defroster)To front door window
(Side defroster)
Side ventilator
Side ventilator Centre ventilator
To passenger
seat footwell
(Foot duct)
To front door window
(Side defroster)
To driver seat footwell
Ad
optin g the f l ow-sp eed type de froste r and th e uni-
fied heate r syst em allows th e ventilation system with
high
defogg ing p e rformance . In ad dition, the air ou t
-
let of defroster is so located as no t to be vie w e d from
the fron
t sea t s, there b y impro v ing the ro om ap pear
-
ance.

VENTILATION SYSTEM
HEATER, AIR CONDITIONER AND VENTILATION55-12
VENTILATION SYSTEM
M2551002000305
AC206030AB
Air outlet
Fresh ai r is drawn fro m the f r ont deck, a nd extracte d
fro
m air ou tlet lo cate d be hind th e re ar bu mp er . Area s
of fresh
air int a ke h o le and a i r outlet vent ilat i on have
been o
p timise d in order to imp r ove air volume (venti
-
lation perfo rman ce) while secu ring cabin quietness.

GENERAL INFORMATION
MULTIPOINT FUEL INJECTION (MPI) <4A9>13A-6
List of Component Functions
NameFunction
ECU
Engine-ECU or engine-CVT-ECU The signals that are input by the sensors enable the
actuators to be controlled in accordance with the
driving conditions.
Sensors
Ignition switch-IGThis signal indicates the ON/OFF condition of the
ignition switch. When this signal is input, the
engine-ECU or engine-CVT-ECU
supplies power to the crank angle sensor, camshaft
position sensor, etc.
Ignition switch-STThis signal indicates that the engine is cranking.
Based on this signal, the engine-ECU or
engine-CVT-ECU controls the fuel injection,
throttle valve position, and the injection timing that
are suited for starting the engine.
Manifold absolute pressure sensor Uses a pressure conversion element to detect the
pressure in the intake manifold, converts it into a
voltage signal, and outputs it to the
engine-ECU or engine-CVT-ECU. The
engine-ECU or engine-CVT-ECU
optimally corrects the fuel injection amount and the
like based on this signal.
Oxygen sensor This sensor, which contains zirconia and platinum
electrodes, detects the level of oxygen concentration
in the exhaust gases. The engine-ECU or
engine-CVT-ECU determines whether the
air-fuel ratio is at the optimal stoichiometric ratio in
accordance with this oxygen concentration level.
Barometric pressure sensorThis sensor detects the altitude of the vehicle. It
enables the engine-ECU or engine-CVT-ECU
to make fuel injection volume corrections in
order to achieve an appropriate air-fuel ratio.
Intake air temperature sensorThis sensor, which contains a thermistor, detects the
temperature of the intake air. The engine-ECU
or engine-CVT-ECU makes fuel injection
volume corrections that suit the intake air
temperature, in accordance with the voltage that is
output by this sensor.
Engine coolant temperature sensorThis sensor, which contains a thermistor, detects the
temperature of the engine coolant. The engine-ECU
or engine-CVT-ECU determines the
warm-up condition of the engine in accordance with
the voltage that is output by this sensor, in order to
control the fuel injection volume, idle speed, and
ignition timing.

DIAGNOSIS SYSTEM
MULTIPOINT FUEL INJECTION (MPI) <4A9>13A-14
DIAGNOSIS SYSTEM
M2132009000882
Engine-ECU or engine-CVT-ECU has
been provided with the following functions for easier
system inspection.FREEZE-FRAME DATA
When the engine-ECU or engine-CVT-ECU
detects a problem and stores the resulting
diagnosis code, the engine condition at that time is
also memorized. The M.U.T.-III can then be used to
analyze this data in order to increase the effective
-
ness of troubleshooting. The freeze-frame data dis-
play items are given below.
Item No.DataUnit
13Intake air temperature sensor°C
21Engine coolant temperature sensor°C
22Crank angle sensorr/min
24Vehicle speed sensorkm/h
32Manifold absolute pressure sensorkPa
44Ignition advancedeg
81Long-term fuel compensation%
82Short-term fuel compensation%
87Calculated load value%
88Fuel control conditionOpen loopOL
Closed loopCL
Open loop owing to drive conditionOL-DRV
Open loop owing to system malfunctionOL-SYS
Closed loop based on one oxygen sensorCL-HO2S
8AThrottle position sensor (main)%
A1Oxygen sensor (front)V
A2Oxygen sensor (rear)V
DIAGNOSIS CODE
The diagnosis and engine warning lamp items are
given in the table below.
Code No.Diagnosis itemMain diagnosis contentsEngine
warning lamp
P0011Variable valve timing systemAbnormal MIVEC system−
P0105Manifold absolute pressure sensor
systemOpen circuit or short-circuit in
sensor-related circuitsON
P0110Intake air temperature sensor
systemOpen circuit or short-circuit in
sensor-related circuitsON
P0115Engine coolant temperature sensor
systemOpen circuit or short-circuit in
sensor-related circuitsON
P0122*Throttle position sensor (main)
circuit low inputOpen circuit or short-circuit in
sensor-related circuitsON
P0123*Throttle position sensor (main)
circuit high inputShort-circuit in sensor-related
circuitsON

DIAGNOSIS SYSTEM
MULTIPOINT FUEL INJECTION (MPI) <4A9>13A-17
DATA LIST FUNCTION
The data list items are given in the table below
Item No.Inspection itemUnit
11Oxygen sensor (front)mV
13Intake air temperature sensor°C
14Throttle position sensor (sub)mV
16Power supply voltageV
18Cranking signal (ignition switch-ST)ON/OFF
21Engine coolant temperature sensor°C
22Crank angle sensorr/min
25Barometric pressure sensorkPa
29Inhibitor switchP or N/D, DS, L, or R
32Manifold absolute pressure sensorkPa
41Injectorsms
44Ignition advanceBTDC
49A/C relayON/OFF
59Oxygen sensor (rear)mV
67Stop lamp switchON/OFF
68Exhaust gas recirculation valveSTEP
77Accelerator pedal position sensor (sub)mV
78Accelerator pedal position sensor (main)mV
79Throttle position sensor (main)mV
7EVariable valve timing phase angleCA
13*Intake air temperature sensor°C
21*Engine coolant temperature sensor°C
22*Crank angle sensorr/min
24*Vehicle speed sensorkm/h
32*Manifold absolute pressure sensorkPa
44*Ignition advancedeg
81*Long-term fuel compensation%
82*Short-term fuel compensation%
87*Calculated load value%
88*Fuel control conditionOpen loopOL
Closed loopCL
Open loop owing to drive
conditionOL-DRV
Open loop owing to system
malfunctionOL-SYS
Closed loop based on one
oxygen sensorCL-HO2S

DIAGNOSIS SYSTEM
MULTIPOINT FUEL INJECTION (MPI) <4A9>13A-19
Engine-ECU or engine-CVT-ECU
Monitor Item
•Items useful for grasping the engine control con-
dition by the engine-ECU or
engine-CVT-ECU are provided in this
monitor item section.
•Values of these monitor items vary greatly
depending on marginal difference of measure
-
ment conditions, difference of the environment,
aged deterioration of vehicles and so on, and it is
difficult to show the precise specification values.
Therefore, check conditi ons, display range and
movement of values are described.
Item No.Inspection itemDisplay range, numerical value
5AAir-fuel ratio learning value of B zone (Low
speed load)−25 to 25%
5BIdle speed control position learned value−128 to 127STEP
5CIdle speed control position learned value (A/C
load)−128 to 127STEP
6AKnock retardRetards in response to accelerator opening
6BLearned knock retard0 − 100%
6CTarget idle speedChanges in response to engine coolant
temperature
9BAir-fuel ratio learning value of A zone (Low
load)−25 to 25%
9DAir-fuel ratio feedback integration−25 to 25%
B2Alternator G terminal dutyIncreases
B3Purge control solenoid valve duty0 − 100%
81*Long-term fuel compensation−25 to 25%
82*Short-term fuel compensation−25 to 25%
87*Calculation load value0 − 100%
88*Fuel control conditionChanges depending on driving condition
NOTE: *: This item is not displayed when the data list in check mode is selected.