2006 MERCEDES-BENZ R350 tow

201 Controls in detail
Automatic transmission
Even though this is possible, make it a
practice to always shift into park
positionP before turning off the engine
and remove the SmartKey from the
starter switch, or when using
KEYLESS-GO*, before turning off the
engine with the start/stop button and
opening the driver’s door.!If you want the gear position to remain
inN (for example when the vehicle is
pulled through a car wash)


do not remove the SmartKey from
the starter switch
or, when using KEYLESS-GO*


do not turn off the engine using the
KEYLESS-GO start/stop button*
and open the driver’s door
Otherwise, the transmission will shift
toP and lock the wheels, preventing
the vehicle from being pulled through a
car wash.
Effect
í
Reverse gear
Shift into reverse gearR only
when the vehicle is stopped.
ë
Neutral
No power is transmitted from the
engine to the drive axle. When
the brakes are released, the
vehicle can be moved freely
(pushed or towed).
To avoid damage to the trans-
mission, never shift into neutral
positionN while driving.
If the ESP
® is deactivated or
malfunctioning:
Shift into neutral positionN only
if the vehicle is in danger of
skidding, e.g. on icy roads.
ê
Drive
The transmission shifts
automatically. All forward gears
are available.
!Coasting the vehicle, or driving for any
other reason in neutral positionN can
result in transmission damage that is
not covered by the Mercedes-Benz
Limited Warranty.Warning!
G
Getting out of your vehicle without shifting
into park positionP is dangerous. Also, park
positionP alone is not intended to or capa-
ble of preventing your vehicle from moving,
possibly hitting people or objects.
Always set the parking brake in addition to
shifting to park positionP (
page 65).
When parked on an incline, turn the front
wheels towards the road curb.
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.

208 Controls in detailGood visibilityFor information on the windshield wipers,
see “Windshield wipers” (
page 59).
Headlamp cleaning system*
The button is located on the left side of the
dashboard.
1Headlamp washer button
Switch on the ignition (
page 38).

Press button1.
The headlamps are cleaned with a
high-pressure water jet.For information on filling up the washer
reservoir, see “Windshield / rear window
washer system and headlamp cleaning
system*” (
page 352).
Rear view mirrors
For more information on setting the rear
view mirrors, see “Mirrors” (
page 47).
Interior rear view mirror, antiglare
position
1Lever

Tilt the mirror to the antiglare night
position by moving lever1 towards
the windshield.
The interior rear view mirror is dimmed.
iThe headlamps will automatically be
cleaned when you have

switched on the headlamps
and


operated the windshield wipers
with windshield washer fluid
fifteen times
When you switch off the ignition, the
counter resets.

271 Controls in detail
Driving systems
Basic settings
There are two setting from which to
choose:

Raised level, for driving on rough roads


Highway level, for driving on paved
roads in fair or better conditionCompared to the highway level, the vehicle
level changes by


+ 1.97 in (+ 50 mm) in raised level


+/- 0 in (+ 0 mm) in highway level


- 0.78 in (- 20 mm) in highspeed level
The vehicle lowers to highspeed level auto-
matically when


the vehicles speed exceeds
70 mph (112 km/h)


the vehicles speed is between
60 mph (96 km/h) and
70 mph (112 km/h) for longer than 20
seconds
!Keep in mind that in rough or uneven
roads, adjusting the vehicle to a lower
level may cause the vehicle underbody
to come in contact with the road and
result in damage to the vehicle under-
body. Always make sure the vehicle
has sufficient ground clearance before
adjusting it to a lower level.!Before jacking up the vehicle with
equipment that lifts one or more of the
wheels completely off the ground,
remove the SmartKey from the starter
switch.!Please also note the information in the
section on towing (
page 499).
iThe activation threshold is defined by
the set suspension tuning
(page 269).
iThe high-speed level is not available
when towing a trailer.iThe third available level is the
highspeed level that is set automatical-
ly.
iObey local speed limits. Use prudent
driving speeds appropriate to prevail-
ing conditions.

280 Controls in detailLoadingLoading instructionsThe gross vehicle weight which is the
weight of the vehicle including fuel, tools,
spare wheel, installed accessories, pas-
sengers, and luggage/cargo must never
exceed the load limit and the Gross Vehicle
Weight Rating (GVWR) for your vehicle as
specified on the placard(s) located on the
driver’s door B-pillar (
page 510). In addi-
tion, the load must be distributed in such a
way so that the weight on each axle never
exceeds the Gross Axle Weight Rating
(GAWR) for the front and rear axle. The
GVWR and GAWR for your vehicle are indi-
cated on the certification label which can
be found on the driver’s door B-pillar
(
page 510).
For more information, see “Tire and Load-
ing Information” (
page 357).
The handling characteristics of a fully load-
ed vehicle depend greatly on the load dis-
tribution. It is therefore recommended to
load the vehicle according to the illustra-
tions shown, with the heaviest items being
placed towards the front of the vehicle.
Warning!
G
Always fasten items being carried as secure-
ly as possible using cargo tie-down rings and
fastening materials appropriate for the
weight and size of the load.
In an accident, during hard braking or sud-
den maneuvers, loose items will be thrown
around inside the vehicle, and can cause in-
jury to vehicle occupants unless the items
are securely fastened in the vehicle.
To help avoid personal injury during a colli-
sion or sudden maneuver, always use parti-
tion net when transporting cargo.
Never drive vehicle with the tailgate open.
Deadly carbon monoxide (CO) gases may
enter vehicle interior resulting in uncon-
sciousness and death.

291 Controls in detail
Loading


With the cargo compartment fully ex-
panded (
page 284), use holders
above B-pillars 1 and the cargo
tie-down rings in the second-row foot-
well (
page 282).

Open the zipper on the partition net
package.

Roll out the partition net.

Unfold the partition net.
The partition net bar must audibly en-
gage.Engaging partition net
1Holder
2Mounting hook

One after the other, engage mounting
hooks2 in holder1.

Push mounting hooks2 forward into
holder1.Tightening partition net in second row
1Tensioner
2Hook
3Tie-down ring

Guide hook2 towards tie-down
ring3.

Pull tensioner1 down in direction of
arrow towards tie-down ring3.

Insert hook2 in tie-down ring3.

Release tensioner 1.

292 Controls in detailLoadingRemoving partition net
Release tensioning of the strap by pull-
ing tensioner1 down.

Disengage hook2 from tie-down
ring3.

Remove mounting hooks2 from
holder1, see “Engaging partition net”
(page 291).

Roll up the partition net.

Press the red button on the partition
net bar.

Fold partition net bar.

Roll up the partition net.

Close zipper on partition net package.Tightening partition net in third row
1Hook
2Tie-down ring

Insert hook1 in tie-down ring2.3Partition net ring
4Tensioner hook
5Tensioner

Pull tensioner5 up in direction of ar-
row towards partition net ring3.

Insert tensioner hook 4 in partition
net ring 3 located at lower edge of the
partition net.

Release tensioner 1.

310 Controls in detailUseful features3Rear center console base
6Rear center console
Position center console 6 above
base3.

Insert the tabs at rear of center
console6into anchorage points4
or 5 on base 3.

Guide front of center console6 down
towards base 3.
Center console 6 must rest on
base3.

Press down on front of center
console6 until it audibly engages in
latch1or2.
Telephone*
Radio transmitters, such as a portable tele-
phone or a citizens band unit, should only
be used inside the vehicle if they are con-
nected to an antenna that is installed on
the outside of the vehicle.
The external antenna must be approved by
Mercedes-Benz. Please contact an autho-
rized Mercedes-Benz Light Truck Center
for information on the installation of an ap-
proved external antenna. Refer to the radio
transmitter operation instructions regard-
ing use of an external antenna.Warning!
G
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and/or serious
personal injury.
Warning!
G
Please do not forget that your primary re-
sponsibility is to drive the vehicle. A driver’s
attention to the road must always be
his / her primary focus when driving. For
your safety and the safety of others, we rec-
ommend that you pull over to a safe location
and stop before placing or taking a tele-
phone call.
If you choose to use the telephone
1 while
driving, please use the hands-free device
and only use the telephone when road,
weather and traffic conditions permit. Some
jurisdictions prohibit the driver from using a
cellular telephone while driving a vehicle.
Only operate the Modular COMAND
System
1 if road, weather and traffic condi-
tions permit.
Bear in mind that at a speed of just 30 mph
(approximately 50 km / h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
1Observe all legal requirements


316 Controls in detailUseful featuresThe Mercedes-Benz Roadside Assistance
dispatcher will either dispatch a qualified
Mercedes-Benz technician or arrange to
tow your vehicle to the nearest
Mercedes-Benz Light Truck Center. For
services such as labor and/or towing,
charges may apply. Refer to the Roadside
Assistance Manual for more information.
These programs are only available in the
USA:

Sign and Drive services: Services such
as jump start, a few gallons of fuel or
the replacement of a flat tire with the
vehicle spare tire are obtainable.
iThe indicator lamp on the Roadside
Assistance button• remains illumi-
nated in red for approximately
10 seconds during the system
self-check after switching on the igni-
tion (together with the SOS button and
the Information button¡).
See system self-check (
page 312) if
the indicator lamp does not come on in
red or stays on longer than
approximately 10 seconds.
If the indicator lamp on the Roadside
Assistance button• is flashing
continuously and there was no voice
connection to the Response Center
established, then the Tele Aid system
could not initiate a Roadside Assis-
tance call (e.g. the relevant cellular
phone network was not available). The
message
Call failed
appears in the
multifunction display.
Roadside Assistance calls can be
terminated using thet button on
the multifunction steering wheel or the
END Button on the Modular COMAND
System.