2006 LEXUS RX330 center

OCCUPANT RESTRAINT SYSTEMS
140
SEATS
While the vehicle is being driven, all vehicle occupants should
have the seatback upright, sit well back in the seat and properly
wear the seat belts provided.
CAUTION
 Do not drive the vehicle unless the occupants are
properly seated. Do not allow any passengers to sit
in the luggage compartment or cargo area. Persons
not properly seated and/or not properly restrained by
seat belts can be severely injured in the event of
emergency braking or a collision.
 During driving, do not allow any passengers to stand
up or move around between seats. Otherwise, severe
injuries can occur in the event of emergency braking
or a collision.
FRONT SEATS
Front seat precautions
Driver seat
CAUTION
The SRS driver airbag deploys with considerable force,
and can cause death or serious injury especially if the
driver is very close to the airbag. The National Highway
Traffic Safety Administration (“NHTSA”) advises:
Since the risk zone for driver airbag is the first 50 — 75
mm (2 — 3 in.) of inflation, placing yourself 250 mm (10
in.) from your driver airbag provides you with a clear
margin of safety. This distance is measured from the
center of the steering wheel to your breastbone. If you
sit less than 250 mm (10 in.) away now, you can change
your driving position in several ways:
 Move your seat to the rear as far as you can while still
reaching the pedals comfortably.

OCCUPANT RESTRAINT SYSTEMS
148
REAR SEATS
Sliding and reclining rear seats
Sliding the rear seats — Hold the center of the slide lock
release lever and pull it up. Then slide the seat to the
desired position with slight body pressure and release the
lever.
Reclining the rear seats — Pull the seatback lock release
lever. Then lean back to the desired angle and release the
lever.
CAUTION
Avoid reclining the seatback any more than needed.
The seat belts provide maximum protection when the
passengers are sitting up straight and well back in the
seats. If you are reclined, the lap belt may slide past
your hips and apply restraint forces directly to the
abdomen or your neck may contact the shoulder belt.
In the event of a frontal collision, the more the seat is
reclined, the greater the risk of death or personal injury.

OCCUPANT RESTRAINT SYSTEMS
150
Folding down rear seatbacks
Lower the head restraints, unlock the seatbacks by pulling
the seatback lock release lever and fold them down until
they lock.
When returning the rear seatbacks to their original
positions, unlock the seatbacks by pulling the seatback
lock release lever and lift them up until they lock. Folding down rear center seatback
You can fold down only the rear center seatback.
To fold down the center seatback, lower the center head
restraint, unlock the seatback by pulling the center
seatback lock release lever behind the seatback and fold
it down. To return the center seatback to its original
position, lift the center seatback up until it locks.

OCCUPANT RESTRAINT SYSTEMS
152
HEAD RESTRAINTS
For your safety and comfort, adjust the head restraint
before driving.
Front seats
To raise the head restraint, pull it up. To lower it, press the
lock release button and push the head restraint down. To
move the head restraint forward or rearward, pull or push
the base of the head restraint.
The head restraint is most effective when it is close to your
head. Therefore, using a cushion on the seatback is not
recommended.
CAUTION
Adjust the center of the head restraint so that it is
closest to the top of your ears.
 After adjusting the head restraint, make sure it is
locked in position.
 Do not drive with the head restraints removed.

OCCUPANT RESTRAINT SYSTEMS
153
Rear seats
To raise the head restraint, pull it up. To lower it, press the
lock release button and push the head restraint down.
Rear center head restraint — When an occupant sits on the
rear center seat, always pull up the rear center head restraint
to the lock position.
The head restraint is most effective when it is close to your
head. Therefore, using a cushion on the seatback is not
recommended.
CAUTION
Adjust the center of the head restraint so that it is
closest to the top of your ears.
 After adjusting the head restraint, make sure it is
locked in position.
 Do not drive with the head restraints removed.

OCCUPANT RESTRAINT SYSTEMS
158
Front seat belts only
Adjust the shoulder anchor position to your size.
To raise the anchor position, push the anchor up. To lower the
anchor position, support the anchor while you push the lock
release button then slide the anchor down. After the
adjustment, make sure the anchor is locked in position.
CAUTION
Always make sure the shoulder belt is positioned
across the center of your shoulder . The belt should be
kept away from your neck, but not falling off your
shoulder. Failure to do so could reduce the amount of
protection in an accident and cause serious injuries in
a collision.

OCCUPANT RESTRAINT SYSTEMS
161
2. Pinch the two edges of the shoulder belt for the rear
seat outboard position with your fingers and slide the belt
past the slot of the guide as shown above. At this time, the
elastic cord must be behind the seat belt.
CAUTION
Make sure the belt is not twisted and that it lies flat. The
elastic cord must be behind the belt and the guide must
be on the front.
3. Buckle, position and release the seat belt. (For wearing
the seat belt, see page 156.)
CAUTION
Always make sure the shoulder belt is positioned
across the center of the shoulder. The belt should be
kept away from the neck, and should not fall off the
shoulder. Failure to observe these precautions could
reduce the effectiveness of the seat belt in an accident,
causing death or serious injury.

OCCUPANT RESTRAINT SYSTEMS
203
1Same position2Same angle
When installing a child restraint system in the rear
center position, adjust both seat cushions to the
same position and align both seatbacks at the same
angle. Otherwise, the child restraint system cannot
be securely restrained and this may cause death or
serious injuries in a collision.
1. Run the lap and shoulder belt through or around the infant
seat following the instructions provided by its manufacturer
and insert the tab into the buckle taking care not to twist the
belt. Keep the lap portion of the belt tight.