2006 LEXUS LX470 change

SWITCHES
32
HEADLIGHT DIMMER AND TURNSIGNAL SWITCH
12X002a
For high beam, push the lever forward. Pull it back for low
beam. For the headlight flasher, pull it further back.
A blue light in the instrument cluster indicates high beam or
headlight flasher is on.
The headlight flasher works even when the headlight switch is
off.
12X003a
For signaling turns, move the lever up or down in the
conventional manner.
The ignition key must be in the “ON” position.
The turn signal is self −cancelling after a turn, but after a lane
change, you may have to cancel it by hand. You can also signal
a lane change by moving the turn signal lever partway and
holding it there.
If the green light in the instrument cluster flashes faster than
normal, it indicates that the front or rear turn signal bulb has
burned out. If this indicator light does not come on, the fuse
or the indicator light itself has probably failed.

SWITCHES
34Twist the aut
omatic control adjuster in the “–” direction to
lower the sensitivity, and the “+” direction to boost the
sensitivity.
With the ignition switch turned off, if the windshield sensor is
touched by reason of cleaning the windshield or for any other
reason, either of the following operations may cause automatic
wiper activation.
 Turning the ignition switch on with the wiper lever in the
“AUTO” position.
 Turning the ignition switch on and move the wiper lever
down in the “AUTO” position.
Even with the wiper lever in the “AUTO” position, the system
will switch to intermittent operations if the system malfunctions.
When the system malfunctions, the time interval between
sweeps is shortened as the vehicle speed increases. When
the vehicle speed reaches more than about 20 km/h (12 mph)
with the interval adjuster in “+” position, the time interval
becomes the shortest 1.5 seconds.
The system will turn off if the windshield gets extremely hot (at
more than 90 C or 194F) or cold (at less than –30 C or
–22 F).
CAUTION
Be careful not to get your fingers caught between the
wipers and windshield.
When the wiper lever is in the “AUTO” position with the
ignition switch on, the wipers could operate
automatically in the following cases:
 If you touch the upper center of the windshield
adjacent to the sensor.
 If you wipe the upper center of the windshield
(adjacent to which the sensor is located) with a towel.
 If the windshield vibrates.
 If you touch the sensor.
If you stop the vehicle with the wiper switch in the “LO” position,
the wiper speed automatically changes from low speed to
intermittent operation speed.* This function does not work
when the interval adjuster is in the “+” position.
NOTE: *This feature can be deactivated. Ask your Lexus
dealer for details.

SWITCHES
36
REAR WINDOW WIPER ANDWASHER SWITCH
12X009b
 1Washer on during wiping 2Washer on
To turn the wipers on, twist the knob at the end of the lever.
The ignition key must be in the “ON” position.
There are 2 settings:
“LO” position: Intermittent operation
“HI” position: Normal operation
If you stop the vehicle with the rear window wiper switch in the
“ON” position, the wiper speed automatically changes from low
speed to intermittent operation speed. If you shift the selector lever
to the “R” position while the
windshield wipers are operating or for 17 seconds after the
windshield wipers stop operating, the rear window wiper will
activate once.*
NOTE: *This feature can be deactivated. Ask your Lexus
dealer for details.
To make the washer squirt, twist the knob downward to
position 2.
The rear wiper will automatically make 3 wipes and then a
single wipe later to sweep the rear window completely.
To make the washer squirt while operating in “ON”
position, twist the knob upward to position 1.
The knob automatically returns from these positions after you
release it.
If the rear window wiper is off, it will operate a couple of times
after the washer squirt.
The low washer fluid warning light in the instrument cluster
comes on when the fluid level in the tank becomes very low.
For information on adding washer fluid, see “Adding washer
fluid” on page 458.
NOTICE
Do not operate the rear window wiper if the rear window
is dry. It may scratch the glass.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
48
FUEL GAUGE
13X500
Low fuel level warning light
The gauge indicates the approximate quantity of fuel
remaining in the tank when the ignition switch is on.
It is a good idea to keep the tank over 1/4 full.
If the fuel level approaches “E” or the low fuel level warning light\
comes on, fill the fuel tank as soon as possible.
On inclines or curves, due to the movement of fuel in the tank,
the fuel gauge needle may fluctuate or the low fuel level
warning light may come on earlier than usual.
If the fuel tank is completely empty, the malfunction indicator
lamp comes on. Fill the fuel tank immediately.
The indicator lamp goes off after driving several times. If the
indicator lamp does not go off, contact your Lexus dealer as
soon as possible. See the inner back cover for fuel capacity and recommended
fuel selection.
ENGINE COOLANT
TEMPERATURE GAUGE
13X501
 Normal range
The gauge indicates the engine coolant temperature when
the ignition switch is on. The engine operating
temperature will vary with changes in weather and engine
load.
If the needle points to the red zone or higher, stop your vehicle
and allow the engine to cool.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
51
TACHOMETER
13X504c
The tachometer indicates engine speed in thousands of
rpm (revolutions per minute). Use it while driving to
prevent engine overrevving.
Driving with the engine running too fast causes excessive
engine wear and poor fuel economy. Remember, in most
cases the slower the engine speed, the greater the fuel
economy.
NOTICE
Do not let the indicator needle get into the red zone. This
may cause severe engine damage.
ODOMETER AND TRIP METER
13X505
“ODO/TRIP” knob
This meter displays the odometer and two trip meters. To
change the mode indication, push the “ODO/TRIP” knob
briefly. Each time you push the knob, the mode changes
in order from the odometer to trip meter A to trip meter B,
then back to the odometer, etc.
The odometer records the total distance the vehicle has
been driven. The twin trip meter records two different
distances independently.
For example, you can use one meter to calculate the fuel
economy and the other to measure the distance on each trip.
To set the A trip meter to zero, display the A meter reading,
push the knob and hold it. The same applies for the B trip
meter.
The data of trip meters will be cancelled if the electrical power
source is disconnected.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
60
(l) Vehicle Stability Control System andActive Traction Control System Warning
Light
This light warns that there is a problem somewhere in the
vehicle stability control system and active traction control
system.
If the “VSC/TRAC” warning light and “VSC OFF” indicator light
come on, have your vehicle checked by Lexus dealer as soon
as possible. However, it is no problem that the “VSC/TRAC”
warning light comes on when the brake actuator temperature
becomes high. (For details, see “Active traction control
system” on page 288.)
The lights will stay on with the ignition key turned to “ON”, and
will go off after about a few seconds.
The lights may stay on for 60 seconds after the ignition key is
turned to the “ON” position. It is normal if they go out after a
while.
Depressing the brake pedal repeatedly may turn on the lights.
It is normal if they go out after a few seconds.
When the “VSC/TRAC” warning light and “VSC OFF” indicator
light come on, the vehicle stability control system and/or active
traction control system do not operate, but there is no problem
to continue your driving.
(m) Variable Gear Ratio Steering System Warning Light
This light warns that there is a problem somewhere in the
variable gear ratio steering system.
The light will come on when the ignition key is turned to “ON”
and will go off after a few seconds.
If the light comes on while driving, the system is not working.
Although conventional steering operates when maneuvered,
a larger degree of wheel maneuvering (than at the time when
the system is functioning properly) is needed when driving at
low speed. At this time, the center position of the steering
wheel could be changed. Although it is no problem to continue
driving, have your vehicle repaired at your Lexus dealer.
In the following cases, contact your Lexus dealer:
 The warning light does not come on after the ignition key is
turned to “ON”.
 The warning light remains on after the ignition key is turned
to “ON”.
 The warning light comes on while driving.
The light will flash if you disconnect and reconnect the battery
terminal. This is because the system is reset temporarily.
However, it is no problem to drive. To turn off the light, drive for
a short while. The system will be set automatically and return
to normal.

222
GAUGES, METERS AND SERVICE REMINDER INDICATORS
63
The following service reminder indicators go off after a few
seconds.

w73

w72a

218
214 wtracorw227
or

The following service reminder indicat
or goes off after about 6
seconds.
The anti −lock brake system warning light, vehicle stability
control system off indicator light and vehicle stability control
system and active traction control system warning light may
stay on for about 60 seconds after the ignition key is turned to
the “ON” position. It is normal if they go out after a while.
If any service reminder indicator or warning buzzer does not
function as described above, have it checked by your Lexus
dealer as soon as possible.
TRIP INFORMATION DISPLAY (Vehicles without navigation system)
13x541z
The following information is shown with the ignition
switch turned on. Each time you push the “MODE” button,
the displayed information is changed.
 Average vehicle speed
 Driving distance after engine starting
 Available driving range
 Average fuel consumption after being refueled
 Current fuel consumption
The displayed trip information values indicate the general
driving condition and may not always reflect precise and actual
conditions.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
66
13x531a
The unit shown on the display can be changed using the
following procedure:
1. Hold down the “MODE” button until the unit flashes.
2. Push the “RESET” button to change the unit.
3. Push the “MODE” button.
When you change the unit shown on the trip information
display, the unit on the outside temperature display is also
changed.
INSTRUMENT PANEL LIGHTCONTROL
13X019
To adjust the brightness of the instrument panel lights,
turn the dial.
When the surroundings are dark and when the headlight
switch is in the first or second click stop, you can also adjust
the brightness of the displays on the clock and audio and air
conditioning systems using this dial.