2006 KIA Sorento child lock

INTERIOR AND EXTERIOR OVERVIEWYOUR VEHICLE AT A GLANCE2-2
S2BLA201A
1. Outside rearview mirror
2. Instrument cluster
3. Steering wheel
4. Seat
5. Rear hatch window
6. Rear hatch
7. Door
8. Power window switches
9. Rear door child safety lock
10. Shift lever
11. Parking brake lever
12. Lights
13. Spare tire
1
2
3
4
5
6
7
8
9
10
11
12
13
BL-ENG (CAN)-2.qxd 7/28/05 6:14 PM Page 2-2

Rear Door Child Safety Lock
The child safety lock prevents chil-
dren from opening the rear doors
from the inside. It should be used
whenever children are in the vehicle.
To lock, push the child safety lock to
the “LOCKED”position.To lock a rear door so that it cannot
be opened from the inside, push
the child safety lock located on the
rear edge of the door to the
“LOCKED”position before closing
the door.
To open a rear door while the child
safety lock is engaged, push the
door lock button to the “UNLOCK”
position (red mark is visible) then
pull the outside door handle.
KNOWING YOUR VEHICLE
3-9
LOCKED FREE
S2BLA306
WARNING -
Unattended
Children
An enclosed vehicle can
become extremely hot, causing
death or severe injury to unat-
tended children or animals who
cannot escape the vehicle.
Furthermore, children might
operate features of the vehicle
that could injure them, or they
could encounter other harm,
possibly from someone gaining
entry to the vehicle. Never leave
children or animals unattended
in your vehicle.
CAUTION
The doors should always be
fully closed and locked while
the vehicle is in motion to pre-
vent accidental opening of the
door.
Locked doors will also discour-
age potential intruders when
the vehicle stops or slows.
WARNING
- Rear Door Locks
If children accidentally open the
rear doors while the vehicle is
in motion, the child could fall
out and be seriously injured. To
prevent a child from opening
the rear doors from the inside,
the rear door safety locks
should be used whenever chil-
dren are in the vehicle.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 9

WINDOWSPower Windows
The ignition switch must be in the ON
position for power windows to operate.
Each door has a power window switch
that controls that door’s window.
However, the driver has a power win-
dow switch which can block the opera-
tion of the passenger windows.
Driver’s Door Power Window
Controls
The driver’s door has a master power
window switch that controls all the
windows in the vehicle. The ignition
switch must be in the ON position for
power windows to operate. To open a
window, press down on the front por-
tion of the corresponding switch. To
close a window, pull up on the front
portion of the corresponding power
window switch.Driver’s Window Automatic-down
Window Switch
The driver’s window has an
“Automatic-Down”feature. To activate
the express-down feature, momen-
tarily depress the front of the switch
to the second detent position. To can-
cel this feature, pull up on the front of
the switch and then release it or
momentarily depress the front of the
switch to the first detent position.
Power Window Timer (If equipped)
The power windows can be operated
for approximately 30 seconds after
the ignition key is removed or turned
to the ACC or LOCK position.
However, if the front doors are
opened, the power windows cannot
be operated even within 30 seconds
after the ignition key removal.KNOWING YOUR VEHICLE3-10
S2BLA305C
✽ ✽
NOTICETo prevent the possibility of damage
to the power window system, do not
open or close more than two win-
dows at the same time. This will also
ensure the longevity of the fuse.
WARNING -
Windows
 Do not allow children to play
with the power windows. They
may seriously injure them-
selves or others.
 Always double check to make
sure all arms, hands, and other
obstructions are safely out of
the way before closing a win-
dow.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 10

Driver’s Power Window Switch
The driver’s power window switch
provides two (2) separate window-
down functions.
Depressing the driver’s power win-
dow switch completely lowers the
driver’s window automatically
(Automatic-Down). To cancel this
function, pull up on the front of the
switch and release it or momentari-
ly depress the front of the switch to
the first detent position.
Depressing the driver’s power win-
dow switch partially (to the first
detent) provides precise control of
the window-down position. To
raise/close the driver’s window, pull
up on the power window switch.Power Window Lock Switch
Feature
The driver can disable the power win-
dow switches on a passenger door by
depressing the power window lock
switch located on the driver’s door to
ON. When the power window lock
switch is ON, the driver’s master
control can not operate the passen-
ger door power windows either.
KNOWING YOUR VEHICLE
3-11
S2BLA305D
Power window lock switch
WARNING- Power Windows
 Keep the driver’s door power
window lock switch in the ON
(depressed) position, except
when someone is operating a
passenger door window.
Serious injury can result
(especially to children) from
unintentional window opera-
tion.
 Always double check to make
sure all arms, hands, and
other obstructions are safely
out of the way before closing
a window.
✽ ✽
NOTICEIf you notice buffeting and pulsa-
tion (wind shock) with either side
window open, you should open the
opposite window slightly to reduce
the condition.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 11

Driver Seat Adjustment - Power
(If equipped)
The driver seat can be adjusted by
using the control knob on the outside
of the seat. Before driving, adjust the
seat to the proper position so as to
easily control the steering wheel,
pedals and switches on the instru-
ment panel.
Moving the Front Seat Forward
and Backward
Push the control knob forward or
backward to move the seat to the
desired position. Release the knob
and the seat will lock in that position.KNOWING YOUR VEHICLE3-16
S2BLA340A
CAUTION
Do not operate two knobs at the
same time.
WARNING -
Driver’s Seat
 Never attempt to adjust seat
while the vehicle is moving.
This could result in loss of
control, and an accident caus-
ing death, serious injury, or
property damage.
(Continued)
(Continued)
 In order to avoid unnecessary
airbag injuries including the
possibility of severe injury or
death, always sit as far back
as possible from the steering
wheel while still being able to
maintain comfortable control
of your vehicle.
 The Canadian Motor Vehicle
Safety Standards (CMVSS)
recommends that the driver
sit at least 10 inches (250 mm)
away from the steering wheel
to avoid the risk of serious
injury or death due to the
deployment of the driver’s
airbag.
 The power seats are operable
with the ignition OFF.
Therefore, children should
never be left unattended in the
car.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 16

We strongly recommend that the
driver and all passengers be properly
restrained at all times by using the
safety belts provided with the vehicle.
Proper use of the safety belts
decreases the risk of severe injury or
death in accidents or sudden stops.
In most states, and in Canada, the
law requires their use.
Inertial locks in the safety belt retrac-
tors allow all of the lap/shoulder safe-
ty belts to remain unlocked during
normal vehicle operation.
This allows the occupants some free-
dom of movement and increased
comfort while using the safety belts. If
a force is applied to the vehicle, such
as a strong stop, a sharp turn, or a
collision, the safety belt retractors will
automatically lock the safety belts.Since the inertial locks do not require
a collision to lock up, you may
become aware of the safety belts
locking while braking or going around
sharp corners.
Whenever possible, use the center
rear seat position to install your child
restraint. The center rear seat is the
safest position for a child to sit in. If
the center seat is unavailable, a child
restraint system may be installed in
an outboard rear seat position. Never
install a rear-facing infant seat in the
front passenger position, as an inflat-
ing airbag could cause serious or
fatal injury to a child in that position.The rear safety belts use a special
auto-lock feature designed to allow a
child restraint to be used in these
positions without an added locking
clip. They normally lock only under
extreme or emergency conditions
(emergency lock mode). However
they can be adjusted so that they
remain in fixed and locked when a
child restraint system is placed in
these positions. (Use this auto-lock
mode only to secure a child restraint,
never for passengers restrained by
the safety belts.) Page 3-38 gives
instructions on placing the safety belt
in the auto lock mode.
The drivers safety belt can only oper-
ate in the emergency lock mode.
KNOWING YOUR VEHICLE
3-27
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 27

Restraint of Large Children
As children grow, they may need to
use new child restraints, including
larger child seats or booster seats,
which are appropriate for their
increased size.
A child who has outgrown available
child restraint systems should use
the belts provided in the vehicle.
When seated, the child should be
restrained by the lap/shoulder belt.
If the shoulder belt slightly touches
the child’s neck or face, try placing
the child closer to the center of the
vehicle. If the shoulder belt still
touches their face or neck, they may
need to be returned to a child
restraint system. In addition, after-
market devices are available from
independent manufacturers which
help pull the shoulder belt lower and
away from the child’s face or neck.Placement of a Child Restraint
System
We recommend that, whenever pos-
sible, you put the child restraint in the
center position of the rear seat.
If the center rear seat is not available,
or you are using more than one child
restraint system in the vehicle at the
same time, the rear safety belts have
been designed to allow a child
restraint to be used in these posi-
tions. Since those safety belts nor-
mally lock only under extreme or
emergency conditions (emergency
lock mode) you must manually adjust
those belts to the auto lock mode.
KNOWING YOUR VEHICLE
3-37
WARNING
When a child restraint is not in
use, make sure that it is
secured by a safety belt. In a
sudden stop or accident, a
loose child restraint could be
thrown forward and injure
someone.
✽ ✽
NOTICEThe driver’s safety belt incorpo-
rates the emergency lock mode
only.
WARNING- Restraint Instructions
Failure to observe this manuals
instructions regarding child
restraint systems and the
instructions provided with the
child restraint system could
increase the chance and/or
severity of injury in an accident.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 37

Installing a child restraint system
in the rear center seat
To install a child restraint system in
the rear center seat, do the following:
1. Pull the safety belt webbing and
insert the tongue plate into the
buckle.
2. Do the same procedure in the rear
outboard seat on page 3-38.Placing a passenger safety belt
Into the auto lock mode
The use of the auto lock mode will
ensure that the normal movement of
the child in the vehicle does not
cause the safety belt to be pulled out
and loosen the firmness of its hold on
the child restraint system.
To secure a child restraint in the rear
outboard seats, follow the procedure
below.
1. Place the child restraint system in
the seat and route the lap/shoulder
belt around or through the
restraint, following the restraint
manufacturer’s instructions. Be
sure the safety belt webbing is not
twisted.
KNOWING YOUR VEHICLE3-38
ADVANCED AIRBAG
WARNING- Child Restraint Placement
Never use a child restraint in
the front passenger seat. In a
collision the air bag inflates
with great force. A child in a
restraint in the front passenger
seat can be severely or fatally
injured by the power of the air
bag.
S2BLB350
S2MS103005
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 38