2006 KIA Optima weight

KNOWING YOUR VEHICLE
3-48
PASSENGER PRESENCE
DETECTIONThe passenger presence detection system
detects the presence of a passenger in the
front seat. If no passenger is recognized
on the front passenger seat, the
deployment of the front passenger and/or
side airbag will be prevented. This
system is designed to prevent the
replacement of airbag components that
deploy needlessly in an accident.
WARNING - Front
Passengers
 NEVER use a child restraint
in the front seat. In the front
seat, a child restraint would
be positioned too close to
where the air bags are stored
and in the event an air bag
deploys, the air bag would
impact the child restraint and
cause serious injuries or
death.
 Failure to observe the
instructions provided with
the child restraint system
could increase the risk
and/or severity of injury in an
accident.
WARNING
The passenger presence
detection system is NOT
intended to prevent airbag
deployment while a child is in
the front passenger’s seat. it is
intended ONLY as a means to
reduce unnecessary collision
damage repair expense by
preventing airbag and seat belt
pretensioner deployment when
the right front passenger seat is
unoccupied. Deployment is still
possible if only a few pounds
are placed upon the seat.
Therefore, children must not be
transported in the front seat. All
children must be seated in the
rear seat and properly
restrained with the vehicle’s
restraint system or a child
restraint system appropriate for
the child’s size and weight.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 48

MOVING UP A STEEP GRADE
FROM A STANDING STARTTo move up a steep grade from a
standing start, depress the brake pedal,
shift the shift lever to D (Drive). Select
the appropriate gear depending on load
weight and steepness of the grade, and
release the parking brake. Depress the
accelerator gradually while releasing the
service brakes.
When accelerating from a stop on a
steep hill, the vehicle may have a
tendency to roll backwards. Shifting
the shift lever into 2 (Second Gear)
while in Sports mode will help prevent
the vehicle from rolling backwards.
SHIFT LOCK SYSTEMFor your safety, the Automatic Transaxle
has a shift lock system which prevents
shifting the transaxle out of P (Park)
unless the brake pedal is depressed.
To shift the transaxle out of P (Park) ;
1. Depress and hold the brake pedal.
2. Start the engine or turn the ignition
key to the ON position.
3. Depress the lock release button and
move the shift lever.
When the ignition switch is in the ACC
or LOCK position, the transaxle cannot
be shifted from P (Park).
If the brake pedal is repeatedly depressed
and released with the shift lever in the P
(Park) position, a chattering noise near
the shift lever may be heard.
This is a normal condition.
Note that the ignition key cannot be
removed unless the shift lever is in the P
(Park) position. If the ignition switch is
in any other position, the key cannot be
removed.
4-11
CAUTION
 Shift into the “R” and “P” posi-
tion only when the vehicle has
completely stopped.
 Do not accelerate the engine in
reverse or any of the forward
positions with the brakes applied.
 Always apply the footbrake when
shifting from “P” or “N”, to “R”
or “D” position.
 Do not use the “P” (Park) posi-
tion in place of the parking
brake. Always set the parking
brake, shift the transaxle into
“P” (Park) position and turn off
the ignition when you leave the
vehicle, even momentarily.
Never leave the vehicle unat-
tended while the engine is run-
ning.
 Check the automatic transaxle
fluid level regularly, and add
fluid as necessary.
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 11

 Keep the engine in tune and follow the
recommended periodic maintenance
schedule.
This will increase the life of all parts
and lower your operating costs.
 Do not use the air conditioner
unnecessarily.
 Slow down when driving on rough
roads.
 For longer tire life and better fuel
economy, always keep the tires
inflated to the recommended
pressures.
 Maintain a safe distance from other
vehicles to avoid sudden stops. This
will reduce wear on brake linings and
pads and save fuel because extra fuel
is required to accelerate back to
driving speed.
 Do not carry unnecessary weight in
the vehicle. Do not rest your foot on the brake
pedal while driving. This can cause
needless wear, possible damage to
the brakes, and poor fuel economy.
 Improper wheel alignment causes the
tires to roll at excessive angles,
which results in faster tire wear. It
takes more power to overcome this
improper alignment, which wastes
fuel.
 Open windows at high speeds can
reduce fuel economy.
 Crosswinds and headwinds reduce
fuel economy. To help offset some of
this loss, slow down when driving in
these conditions.
Keeping a vehicle in good operating
condition is important both for
economy and safety.
Therefore, have an Authorized Kia
Dealer perform scheduled inspections
and maintenance.
DRIVING TIPS
5-6
WARNING - Engine OFF
Motion
Never turn the engine off to
coast down hills or anytime the
vehicle is in motion. The power
steering and power brakes will
not function without the engine
running. Instead, downshift to
any appropriate gear for engine
braking effect.
MS-CNA-Eng 5 New.qxd 7/25/2005 5:21 PM Page 6

5-11
TRAILER TOWINGWe do not recommend using this vehicle
for trailer towing.OVERLOADINGLABEL INFORMATION
There are several important labels and
identification numbers located on your
vehicle. The label locations are identified
in the following illustrations.VEHICLE INDENTIFICATION
NUMBER (VIN)
Tire Specification/Pressure LabelThis can be found on the driver side door.
MMSA5001
MMSA7019
CAUTION
The gross axle weight rating
(GAWR) and the gross vehicle
weight rating (GVWR) for your
vehicle are on the manufacturer’s
label attached to the driver’s door
or are listed in the “Specifications”
section of this Owner’s Manual.
Exceeding these ratings can cause
an accident or vehicle damage. You
can calculate the weight of your
load by weighing the items (or
people) before putting them in the
vehicle. Be careful not to overload
your vehicle.
MS-CNA-Eng 5 New.qxd 7/25/2005 5:21 PM Page 11

7-25
TIRES AND WHEELSTIRE CAREFor proper maintenance, safety, and
maximum fuel economy, you must
always maintain recommended tire
inflation pressures and stay within the
load limits and weight distribution
recommended for your vehicle.INFLATION PRESSURESCheck all tire pressures (including the
spare) monthly when the tires are cold.
“Cold tires” means the car has not been
driven for at least three hours or driven
less than one mile (1.6 km).
Recommended pressures must be
maintained to ensure ride quality, vehicle
handling, and minimum tire wear.
Watch the battery during
charging, and stop or reduce
the charging rate if the battery
cells begin gasing (boiling)
violently or if the temperature
of the electrolyte of any cell
exceeds 120°F (49°C).
Wear eye protection when
checking the battery during
charging.
Disconnect the battery
charger in the following
order.
1. Turn off the battery
charger main switch.
2. Unhook the negative
clamp from the negative
battery terminal.
3. Unhook the positive clamp
from the positive battery
terminal.
✻
NOTICE
• Before performing battery
maintenance or recharging, turn
OFF all accessories and stop the
engine.
• When remounted battery,
disconnect the negative (-)
battery cable first. When re-
installing the battery, reconnect
the negative (-) battery cable
last.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 25

MAINTENANCE
7-28COMPACT SPARE TIRE
REPLACEMENTA compact spare tire has a shorter tread
life than a regular size tire. Replace it
when you can see the tread wear indicator
bars on the tire. The replacement compact
spare tire should be the same size and
design tire as the one provided with your
new Kia and should be mounted on the
same compact spare tire wheel. The
compact spare tire is not designed to be
mounted on a regular size wheel, and the
compact spare tire wheel is not designed
for mounting a regular size tire.
WHEEL ALIGNMENT AND
TIRE BALANCEIn addition to proper tire inflation,
correct wheel alignment helps to
minmize tire wear. Your vehicle’s
alignment should be checked every 12
months or 24,000 km (15,000 miles).
Your tires were properly balanced at the
factory, but they may need to be
rebalanced before they wear out. If you
notice a consistent vibration when
driving, have your Kia Dealer inspect
your tires. A tire should always be
rebalanced if it has been removed from
the wheel.
MMSA7022
Tread wear
indicator bar
Indicator
location
✻
NOTICE
Improper wheel weights can
damage your vehicle’s aluminum
wheels. Use only approved wheel
weights.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 28

MAINTENANCE
7-42HEADLIGHT AIMING
ADJUSTMENTBefore performing aiming adjustment,
make sure of the following.
1. Keep all tires inflated to the correct
pressure.
2. Place the vehicle on level ground and
press the front bumper & rear
bumper down several times.
3. See that the vehicle is unloaded
(except for full levels of coolant,
engine oil and fuel, and spare tire, jack,
and tools). Have the driver sit in the
driver’s seat or use equivalent weight.4. Clean the headlight lenses and turn
on the headlight (Low beam).
5. Open the hood.
6. Draw a vertical line (through the
center of each headlight) and the
horizontal line (through the center of
each headlight) on the aiming screen.
1) Horizontal line dimension from
ground: 628 mm (24.72 in)
2) Distance between each vertical
line : 1,306 mm (49.17 in)
And then, draw a parallel line at 30
mm (1.18 in) place under the
horizontal line.
7. Adjust each cut-off line of the low
beam to the parallel line with a
Phillips screwdriver.
ADJUSTMENT AFTER
HEADLIGHT ASSEMBLY
REPLACEMENTIf the vehicle has had front body repair
and the headlight assembly has been
replaced, the headlight aiming should be
checked using the aiming screen as
shown in the illustration. Turn on the
headlight switch. (Low Beam Position)
1. Adjust headlights so that main axis of
light is parallel to center line of the
body and is aligned with point “P”
shown in the illustration.
MMSA7032
Vertical
aiming
HH W
P
MMSA7033
Horizontal line
21 mm (0.82 in)
Cut-off line
Ground line Vertical line
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 42

SPECIFICATIONSThe specifications given here are for general information only.
Please check with an Authorized Kia Dealer for more precise
and more up-to-date information.DIMENSIONS
Unit:mm(in)
WEIGHTSRefer to the compliance label describing GVWR & GAWR
weights attached to your vehicle.
AIR CONDITIONER
SPECIFICATIONS
8-2
Refrigerant complies with SAEJ639R-134a
Maximum operating charge650±25g (20~22oz)
Item 4 Door Sedan
Overall length 4720 (185.8)
Overall width 1815 (71.4)
Overall height 1410 (55.5)
Front tread 1540 (60.6)
Rear tread1 1520 (59.8)
wheelbase 2700 (106.3)
MS-CNA-Eng 8.QXD 7/25/2005 5:07 PM Page 2