Page 108 of 225

TURN SIGNALSThe same lever that controls the head-
lights also controls the turn signals. The
ignition switch must be ON for the turn
signals to function. Move the lever up or
down to activate the turn signals. The
turn signals will self-cancel after a turn is
completed. If the indicator continues to
flash after a turn, manually return the
lever to the OFF (middle) position.
LANE CHANGE SIGNALSTo signal a lane change, move the turn
signal lever slightly and hold it in
position. The lever will return to the
OFF(middle) position when released.
Green arrow indicators on the instrument
panel indicate which turn signal is
operating. If an indicator stays ON and
does not flash or if it flashes abnormally,
one or more of the turn signal bulbs may
be burned out and will require
replacement.
DAYTIME RUNNING
LIGHTS (DRL) Daytime Running Lights (DRL) can
make it easier for others to see the front
of your vehicle during the day. DRL can
be helpful in many different driving
conditions, but they can be especially
helpful in the short periods after dawn
and before sunset.
The DRL system will make your High-
beam headlights turn OFF when:
• the headlight switch is ON.
• the parking brake is engaged.
• the engine stops.
4-29
MMSA4028
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 29
Page 177 of 225

MAINTENANCE
7-1
MAINTENANCEMaintenance Services . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
Owner Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8
Engine Compartment . . . . . . . . . . . . . . . . . . . . . . . . . .7-10
Engine Oil and Oil Filter . . . . . . . . . . . . . . . . . . . . . . . .7-12
Engine Cooling System . . . . . . . . . . . . . . . . . . . . . . . . .7-14
Brakes and Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-17
Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-18
Power Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-18
Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . .7-19
Lubricants and Fluids . . . . . . . . . . . . . . . . . . . . . . . . . .7-20
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-21
Wiper Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-22
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-23
Tires and Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-25
Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-32
Lubricant Specifications . . . . . . . . . . . . . . . . . . . . . . . .7-36
Exterior Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-38
Interior Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-40
Headlight Aiming Adjustment . . . . . . . . . . . . . . . . . . .7-42
7
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 1
Page 208 of 225

MAINTENANCE
7-32WHEEL REPLACEMENTWhen replacing the metal wheels for any
reason, make sure the new wheels are
equivalent to the original factory units in
diameter, rim width and offset.
BULB REPLACEMENTHEADLIGHT BULB
REPLACEMENT
1. Remove the headlight bulb cover by
turning it counterclockwise.
2. Disconnect the headlight bulb
electrical connector.
MMSA7024
CAUTION
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
abilities, handling characteristics,
ground clearance, body-to-tire
clearance, snow chain clearance,
speedometer calibration, headlight
aim and bumper height.
WARNING - Halogen
Bulbs
Wear eye protection when
changing a bulb. Allow the
bulb to cool before handling it.
Halogen bulbs contain
pressurized gas. If broken, a
halogen bulb will explode and
will produce flying pieces of
glass.
Always handle halogen bulbs
carefully to avoid scratches
and abrasions. If the bulbs
are lit, avoid contact with
liquids. Never touch the
glass with bare hands.
Residual oil may cause the
bulb to overheat and burst
when lit. A bulb should be
operated only when installed
in the headlight assembly.
If a bulb becomes damaged
or cracked, replace it
immediately and carefully
dispose it.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 32
Page 209 of 225

7-33
3. Unsnap the headlight bulb retaining
wire.
4. Remove the bulb from the three (3)
slots on the headlight assembly.
5. Install a new headlight bulb in the
three (3) slots on the headlight
assembly and snap the headlight bulb
retaining wire into position.
6. Connect the headlight bulb electrical
connector.
7. Install the headlight bulb cover by
turning it clockwise.
FRONT TURN SIGNAL / POSITION
LIGHT BULB REPLACEMENT1. Remove the bolts from the headlight
assembly.
2. Remove the dust cover.
3. Disconnect the light connector.
4. Remove the light bulb.
5. Insert a new bulb and then connect
the light connector.
6. Install the dust cover and then re-
install the headlight assembly.
FRONT FOG LIGHT
REPLACEMENT (IF EQUIPPED)1. Turn the bulb socket counter-
clockwise and remove the bulb
socket.
2. Insert a new bulb in socket.
3. Install the bulb socket.
MMSA7025
MMSA7026
1. Position light/Turn signal light
2. Headlight
3. Headlight
MMSA7027
1
2
3
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 33
Page 222 of 225
LIGHT BULBS TIRES
* Spare tire(Temporary Spare)
8-3
Light Bulb Wattage
FrontHeadlights 55
65
Turn signal/Position lights 28/8
Fog lights(if equipped) 55
Side mark lights (*if equipped) 5
RearStop and tail lights 28/8
Turn signal lights 27
Backup lights 16
High mounted stop lights 16
Side mark lights (*if equipped) 5
License plate lights 5
InteriorInterior lights 10
Luggage compartment light
5
(If equipped)LOW
HIGH
Size
TireP205/60R15 *T120/70 D15 or T125/70 R15
P205/55R16 (if equipped)
PressureInflation Pressure KPa(kg/cm
2,psi)
210(2.1, 30) 420(4.2, 60)
MS-CNA-Eng 8.QXD 7/25/2005 5:07 PM Page 3