2006 INFINITI QX56 horn

BL-78
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: November 20092006 QX56

through 15A fuse (No. 25, located in fuse and fusible link box).
When the vehicle security system is triggered, ground is supplied intermittently

from IPDM E/R terminal 45

to headlamp high relay and

to horn relay terminal 1.
The headlamps flash and the horn sounds intermittently.
The alarm automatically turns off after 50 seconds, but will reactivate if the vehicle is tampered with again.
VEHICLE SECURITY SYSTEM DEACTIVATION
To deactivate the vehicle security system, a door must be unlocked with the key or keyfob.
When the key is used to unlock the front door LH, BCM terminal 22 receives signal

from terminal 14 of the main power window and door lock/unlock switch.
When the BCM receives this signal or unlock signal from keyfob, the vehicle security system is deactivated.
(Disarmed phase)
PANIC ALARM OPERATION
Remote keyless entry system may or may not operate vehicle security system (horn and headlamps) as
required.
When the remote keyless entry system is triggered, ground is supplied intermittently

from IPDM E/R terminal 45

to headlamp high relay and

to horn relay terminal 1.
The headlamp flashes and the horn sounds intermittently.
The alarm automatically turns off after 25 seconds or when BCM receives any signal from keyfob.
CAN Communication System DescriptionEIS0060G
Refer to LAN-26, "CAN COMMUNICATION" .

BL-86
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: November 20092006 QX56
Terminals and Reference Value for IPDM E/REIS0060K
1*: when horn reminder is ON.
2*: L/W is for USA.
3*: Y is for Canada.
CONSULT-II Function (BCM)EIS0060L
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II INSPECTION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
Te r m i n a l Wire
Color Item
Condition Voltage (V)
(Approx.)
38 B Ground —0
39 L CAN-H ——
40 P CAN-L ——
41 Y/B Hood switch Hood closed
OFF 0V
Hood open ONBattery voltage
45 G/W Horn relay When doors locks are operated
using keyfob (OFF →
ON) *1 Battery voltage
→ 0V
52 L Headlamp low (LH) Ignition
SW ON Lighting
switch
2ND posi-
tion OFF
0V
ON Battery voltage
54 R/Y Headlamp low (RH) Ignition
SW ON Lighting
switch
2ND posi-
tion OFF
0V
ON Battery voltage
55 G Headlamp high (LH) Ignition
SW ON Lighting
switch
HIGH or
PA S S
position OFF
0V
ON Battery voltage
56 L/W *2
Y *3 Headlamp high (RH) Ignition
SW ON Lighting
switch
HIGH or
PA S S
position OFF
0V
ON Battery voltage
59 B Ground —0
BCM
diagnostic test item Diagnostic mode
Description
Inspection by part WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the
BCM for setting the status suitable for required operation, input/output sig-
nals are received from the BCM and received date is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to
them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be
read.
ECU PART NUMBER BCM part number can be read. CONFIGURATION Performs BCM configuration read/write functions.

BL-88
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: November 20092006 QX56
CONSULT-II APPLICATION ITEM
Data Monitor
Active Test
Work Support
Monitored ItemDescription
DOOR SW-AS Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch LH.
BACK DOOR SW Indicates [ON/OFF] condition of back door latch.
TRNK OPN MNTR Indicates [ON/OFF] condition of glass hatch ajar switch.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
KEYLESS UNLOCK Indicates [ON/OFF] condition of unlock signal from keyfob.
KEYLESS LOCK Indicates [ON/OFF] condition of lock signal from keyfob.
KEY CYL LK-SW Indicates [ON/OFF] condition of lock signal from door key cylinder switch.
KEY CYL UN-SW Indicates [ON/OFF] condition of unlock signal from door key cylinder switch.
KEYLESS PBD Indicates [ON/OFF] condition of unlock signal from door key cylinder switch.
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from lock/unlock switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from lock/unlock switch.
HOOD SW Indicates [ON/OFF] condition of hood switch.
Test Item Description
THEFT IND This test is able to check security indicator lamp operation. The lamp will be turned on when
“ON ”
on CONSULT-II screen is touched.
HEADLAMP (HI) This test is able to check vehicle security lamp operation. The high beam headlamps will be acti-
vated for 0.5 seconds after “
ON” on CONSULT-II screen is touched.
VEHICLE SECURITY HORN This test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
onds after
“ON ” on CONSULT-II screen is touched.
Test Item Description
SECURITY ALARM SET This mode can confirm and change security alarm ON-OFF setting.
THEFT ALM TRG The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching
“CLEAR ”
on CONSULT-II screen.

VEHICLE SECURITY (THEFT WARNING) SYSTEMBL-91
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
Symptom ChartEIS0060O
*1: Make sure the system is in the armed phase.SYMPTOM PROCEDURE Diagnostic procedure
1 Vehicle security
system cannot be
set by
···· Door switch Refer to
BL-92, "
Door Switch Check" .
Lock/unlock switch Refer to BL-98, "
Door Lock/Unlock Switch Check" .
Door outside key Refer to BL-96, "
Front Door Lock Assembly LH (Key Cylinder Switch)
Check" .
BCM If the above systems are “OK ”, replace BCM. Refer to BCS-20, "
BCM" .
2 Security indicator
does not turn
“
ON ”. Combination meter Refer to BL-95, "
Combination Meter (Security Indicator Lamp) Check" .
BCM If the above systems are “OK ”, replace BCM. Refer to BCS-20, "
BCM" .
3 *1 Vehicle secu-
rity system does
not alarm when
···· Any door, hood or glass hatch
is opened. Refer to BL-92, "
Door Switch Check" .
Refer to BL-94, "
Hood Switch Check" .
If the above systems are “ OK”, replace BCM. Refer to BCS-20, "
BCM" .
4 Vehicle security
alarm does not
activate. Horn alarm
Refer to BL-98, "
Vehicle Security Horn Alarm Check" .
If the above systems are “ OK”, check horn system.
Refer to WW-55, "
HORN" .
Headlamp alarm Refer to BL-98, "
Vehicle Security Headlamp Alarm Check" .
If the above systems are “ OK”, replace BCM. Refer to BCS-20, "
BCM" .
5 Vehicle security
system cannot be
canceled by
····Door outside key
Refer to BL-96, "
Front Door Lock Assembly LH (Key Cylinder Switch)
Check" .
If the above systems are “ OK”, check main power window and door lock/
unlock switch.
Keyfob Check remote keyless entry function. Refer to
BL-65, "
Keyfob Battery and
Function Check" .
If the above systems are “ OK”, replace BCM. Refer to BCS-20, "
BCM" .

BL-98
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: November 20092006 QX56
Vehicle Security Horn Alarm CheckEIS0060T
1. CHECK HORN OPERATION
Check if horn sounds with horn switch.
Does horn operate?
YES >> Check harness for open or short between IPDM E/R and horn relay.
NO >> Check horn circuit. Refer to WW-55, "
HORN" .
Vehicle Security Headlamp Alarm Check EIS0060U
1. CHECK VEHICLE SECURITY HEADLAMP ALARM OPERATION
Check if headlamps operate with lighting switch.
Do headlamps come on when turning switch ON?
YES >> Headlamp alarm is OK.
NO >> Check headlamp system. Refer to LT- 5 , "
HEADLAMP (FOR USA)" or LT- 3 3 , "HEADLAMP (FOR
CANADA) - DAYTIME LIGHT SYSTEM -" .
Door Lock/Unlock Switch Check EIS0060V
1. CHECK DOOR LOCK/UNLOCK SWITCH INPUT SIGNAL
Check if power door lock operates with door lock/unlock switch.
Do doors lock/unlock when using each door lock/unlock switch?
YES >> Door lock/unlock switch is OK.
NO >> Refer to BL-34, "
Door Lock/Unlock Switch Check" .

BODY REPAIRBL-207
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
CRUSH HORN

Work after 1st crossmember has been removed.
Portions to be welded:
A. Inner side rail crush horn, inner side rail crush horn and outer side rail crush horn.
B. Outer side rail crush horn, outer side rail crush horn and inner side rail crush horn.
LIIA1083E

BL-208
BODY REPAIR
Revision: November 20092006 QX56
Removal Notes

Scribe a straight line on the outer side rail crush horn and inner side rail crush horn along the hole center
as shown in the figure.

Cut off outer side rail crush horn and inner side rail crush horn along scribed line A. Do not cut on the hole.

Cut inner side rail crush horn at 45 mm backward cut position of cut line A. (along line B)
LIIA1084E
LIIA1085E

BL-210
BODY REPAIR
Revision: November 20092006 QX56
Installation Notes

Scribe a straight line on the inner side rail crush horn along the hole center as shown in the figure. Cut off
inner side rail crush horn along scribed line.

Scribe a straight line on the outer side rail crush horn along the hole center as shown in the figure. Cut off
outer side rail crush horn along scribed line.
LIIA1087E
LIIA1088E