2006 INFINITI QX56 sensor

LASER BEAM AIMING ADJUSTMENTACS-13
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56
2. Adjust the height of the target stand so that the point of the trian-
gle aims above the center of the ICC sensor.
ADJUSTING THE POSITION OF THE TARGET BOARD STRING
1. Attach a scale or straightedge (at least 350 mm [14 in] or
longer).
2. Suspend a string with a weight on the end 218 mm (8.6 in) to the left side of the target board center.
POSITIONING THE TARGET
1. Suspend a string with weights on each end over the centerline of the vehicle. The string should lay overthe center of the front and back bumpers. Mark these centerpoints on the ground at each weight.
2. Connect the two center points using a string. Extend the string an additional 5 m (16 ft) beyond the front centerpoint and mark
the floor. Position the target board weight on this mark.
3. Relocate the suspended string from the left side of the target board to the center of the target board. Mark this point on the ground.
WKIA2039E
SKIA1211E
WKIA2040E
WKIA1851E

ACS-14
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: November 20092006 QX56
4. Pivot the target board on its center mark 20° to either side.
NOTE:
Approx. 50 mm (1.97 in) shift will produce a 20 ° movement.
5. Remove any items in the shaded space shown in the figure.
NOTE:
In case the background space shown in the illustration is not available, or if the background is light col-
ored, place a 400 mm (15.75 in) long frosted black board or black cloth to both sides of the target board.
Sensor AdjustmentEKS00BLQ
CAUTION:

Complete all necessary steps for laser beam adjustment until the CONSULT-II indicates "COM-
PLETED". If the procedure does not complete, the ICC system is inoperable.

If CONSULT-II is used without connection to the CONSULT-II CONVERTER, malfunctions might be
detected during self-diagnosis.
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to the data link connector.
PKIA2589E
WKIA1858E
BBIA0369E

LASER BEAM AIMING ADJUSTMENTACS-15
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56
3. Start the engine, wait for at least 10 sec., and touch “START
(NISSAN BASED VHCL) ”.
4. Touch “ICC”.
If “ICC ” is not indicated, go to GI-40, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
5. Touch “WORK SUPPORT ”.
6. Touch “LASER BEAM ADJUST ”.
7. Touch “START”.
CAUTION:
If the adjustment screen does not appear on CONSULT-II 10
sec. after touching “LASER BEAM ADJUST” screen, the fol-
lowing causes may be considered:

Target is not set accurately.

There is not enough space beside the target.

Deformation of vehicle or inappropriate installation of
sensor. Sensor may be installed out of the adjustable
range.
BCIA0029E
BCIA0030E
BCIA0031E
SKIA6191E
WKIA2675E

ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: November 20092006 QX56

The area is not suitable for the adjustment work.

ICC sensor is not clean.
8. After the CONSULT-II displays “ADJUST THE VERTICAL OF
LASER BEAM AIMING” turn the vertical adjusting screw until
“U/D CORRECT ” value is set in the range of ±4.
CAUTION:
Turn the screw slowly. The value on the CONSULT-II is
slower than the actual movement of the ICC sensor. Wait 2
seconds between each adjustment. Also, during adjust-
ment work, do not block the ICC sensor lens with your hand
or body. In that case, there are times when aiming cannot
be conducted correctly.
NOTE:
Turning the screw clockwise raises the ICC sensor and counter-
clockwise lowers the ICC sensor.
9. When “U/D CORRECT ” value indicates ± 4, confirm that the value remains within ±4 for at least 2 seconds
while nothing is touching the ICC sensor.
When “COMPLETED THE VERTICAL AIMING OF LASER
BEAM ” appears on screen, touch “END ”.
CAUTION:
Be sure that the margin of “U/D CORRECT” is within ±4
when the ICC sensor unit is untouched.
10. Confirm that “ADJUSTING AUTOMATIC HORIZONTAL LASER
BEAM AIMING ” is on screen and wait while the horizontal
adjustment is made automatically. (maximum: 10 seconds).
SKIA1221E
WKIA1869E
WKIA2676E
SKIA1224E

ACS-24
[ICC]
TERMINALS AND REFERENCE VALUE
Revision: November 20092006 QX56
TERMINALS AND REFERENCE VALUEPFP:00000
Terminals and Reference Values for ICC UnitEKS00BLU
Terminals and Reference Values for ICC SensorEKS00BLV
Te r m i n a lWire
color Item Condition
Voltage (V)
(Approx.)
Ignition
switch Operation
1W/L Battery power supply OFF— Battery voltage
2W/L
5 P CAN-L —— —
7 B/R N-P RANGE ON A/T selector lever in "P" or "N"Battery voltage
10 V/R Brake booster signal ON—
14 L CAN-H —— —
19 B Ground
ON——
20 B
29 BR/W ICC brake switch
(normally closed) Selector
lever: Not in “N ” or “P ”
position Depress the brake
pedal
0
Release the brake
pedal Battery voltage
30 L DDL-TX —— —
33 R/B Ignition switch power supply ON —
Battery voltage
38 R/G Stop lamp switch
(normally open)
OFFDepress the brake pedal
Release the brake pedal
0
39 V/W DDL-RX —— —
40 G Parking brake signal
ONParking brake is ON
0
Parking brake is OFF Battery voltage
42 R/B Ignition switch power supply —Battery voltage
46 B Ground ——
47 BR Stop lamp drive output signal Brake operating with ICC system
Battery voltage
Brake not operating with ICC
system 0
SKIA1243E
TerminalWire
color Item Condition
Voltage (V)
Ignition
switch Operation
1 R/B Ignition switch power supply
ON—
Battery voltage
2 L CAN-H ——
3 P CAN-L ——
4 B Ground ——

TROUBLE DIAGNOSIS — GENERAL DESCRIPTIONACS-27
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56
6. Touch “WORK SUPPORT ”, “SELF-DIAG RESULTS ”, “DATA
MONITOR ”, "CAN DIAG SUPPORT MNTR", “ACTIVE TEST” or
“ECU PART NUMBER ” on selection screen.
WORK SUPPORT
Work Item
Cause of Auto-Cancel
1. Touch “WORK SUPPORT ” on "SELECT DIAG MODE" screen.
2. Touch “CAUSE OF AUTO-CANCEL ” on "SELECT WORK ITEM"
screen.
3. Cause of automatic cancellation screen will be shown.
4. The last five causes of automatic cancellation of ICC system will be displayed.
Possible Causes of "Auto-Cancel"
Laser Beam Adjust
For details, refer to ACS-12, "LASER BEAM AIMING ADJUSTMENT" .
BCIA0031E
Operation Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
SKIA6191E
Cause of cancellation Description
OPERATING WIPER Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ABS function was operated.
OPERATING TCS TCS function was operated.
OPERATING VDC VDC function was operated.
ECM CIRCUIT ECM did not permit ICC operation.
OPE SW VOLT CIRC Voltage outside the standard was detected.
LASER SUN BEAM Intense light such as sunlight entered ICC sensor light sensing part.
LASER TEMP Temperature around ICC sensor became low.
WHL SPD ELEC NOISE Wheel speed sensor signal caught electromagnetic noise.
OP SW DOUBLE TOUCH ICC steering switches were pressed at the same time.
VDC/TCS OFF SW VDC OFF switch was pressed.
WHEEL SPD UNMATCH Wheel speed became different from AT vehicle speed.
TIRE SLIP Wheel slipped.
PKB SW ON Parking brake is applied.
IGN LOW VOLT Power supply voltage became low.
NO RECORD —

ACS-28
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: November 20092006 QX56
SELF-DIAGNOSTIC RESULTS
For details, refer to ACS-36, "Diagnostic Trouble Code (DTC) Chart" .
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR ” on "SELECT DIAG MODE" screen.
2. Touch “ECU INPUT SIGNALS ”, “MAIN SIGNALS “, or “SELEC-
TION FROM MENU ” on "SELECT MONITOR ITEM" screen.
Monitored Item
×: Applicable
BCIA0031E
WDIA0084E
Monitored Item [unit] MAIN SIGNALS ECU
INPUT
SIGNALS SELECTION
FROM MENU Description
VHCL SPEED SE
[km/h] or [mph] ××× Indicates vehicle speed calculated from
wheel speed sensor signal.
SET VHCL SPD
[km/h] or [mph] ×× Indicates set vehicle speed stored in ICC
unit.
THRTL OPENING
[%] ×××
Indicates throttle angle calculated from sig-
nal voltage of throttle position sensor.
ENGINE RPM
[rpm] ××Indicates engine speed read by ICC unit via
CAN communication (ECM transmits
engine speed via CAN communication).
DISTANCE ADJ
[SHOR/MID/LONG] ×××
Indicates set distance stored in ICC unit.
WIPER SW
[OFF/LOW/HIGH] ××Indicates wiper [OFF/LOW/HIGH] status.
MAIN SW
[ON/OFF] ××× Indicates [ON/OFF] status as judged from
control switch signal.
SET/COAST SW
[ON/OFF] ×××
Indicates [ON/OFF] status as judged from
control switch signal.
CANCEL SW
[ON/OFF] ××× Indicates [ON/OFF] status as judged from
control switch signal.
RESUME/ACC SW
[ON/OFF] ××× Indicates [ON/OFF] status as judged from
control switch signal.
CRUISE OPE
[ON/OFF] ××
Indicates whether vehicle speed is being
controlled or not (ON means “
controlling”).

TROUBLE DIAGNOSIS — GENERAL DESCRIPTIONACS-29
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56
BRAKE SW
[ON/OFF]××× Indicates [ON/OFF] status as judged from
ICC brake switch signal.
STOP LAMP SW
[ON/OFF] ×××
Indicates [ON/OFF] status as judged from
stop lamp switch signal.
RELEASE SW NO
[ON/OFF] ××Indicates [ON/OFF] status as judged from
release switch signal.
ON when brake is depressed.
OFF when brake is not depressed.
RELEASE SW NC
[ON/OFF] ××Indicates [ON/OFF] status as judged from
release switch signal.
OFF when brake is depressed.
ON when brake is not depressed.
IDLE SW
[ON/OFF] ××Indicates [ON/OFF] status of idle switch
read by ICC unit via CAN communication
(ECM transmits ON/OFF status via CAN
communication).
GEAR
[1, 2, 3, 4, 5] ××Indicates A/T gear position read by ICC unit
via CAN communication (TCM transmits
gear position via CAN communication).
BUZZER O/P
[ON/OFF] ×Indicates [ON/OFF] status of ICC warning
output.
ICC WARNING ×NOTE:
This item is displayed but cannot be moni-
tored.
VHCL SPD AT
[km/h] or [mph] ×Indicates vehicle speed calculated from A/T
vehicle speed sensor by ICC unit via CAN
communication (TCM transmits A/T vehicle
speed sensor signal via CAN communica-
tion).
PRESS SENS
[bar] ××× Indicates brake fluid pressure value calcu-
lated from signal voltage of pressure sen-
sor.
PRESS SENS 2
[bar] ××NOTE:
This item is displayed but cannot be moni-
tored.
D RANGE SW
[ON/OFF] ××Indicates [ON/OFF] status of
“D ” position
read by ICC unit via CAN communication
(TCM transmits ON/OFF condition of “ D”
position via CAN communication).
A/T OD OFF
[ON/OFF] ×
Indicates [ON/OFF] status of OD cancel
output under control.
NP RANGE SW
[ON/OFF] ××Indicates PNP switch signal read by ICC
unit via CAN communication. (TCM trans-
mits PNP switch signal via CAN communi-
cation)
DISTANCE ×NOTE:
This item is displayed but cannot be moni-
tored.
RELATIVE SPD ×NOTE:
This item is displayed but cannot be moni-
tored.
STP LMP DRIVE
[ON/OFF] ×× Indicates [ON/OFF] status of brake hold
relay drive output.
Monitored Item [unit] MAIN SIGNALS
ECU
INPUT
SIGNALS SELECTION
FROM MENU Description