2006 INFINITI M35 rear entertainment

AV-292
[WITH MOBILE ENTERTAINMENT SYSTEM]
REMOVAL AND INSTALLATION
Revision: 2006 January2006 M35/M45
Rear Display UnitNKS004BX
: Vehicle front
REMOVAL
1. Insert cloth-covered driver into gaps between rear display cover
(1) and headlining, and remove rear display cover (1).
2. Remove nuts (A) and plastic nuts (B).
3. Disconnect connector, and remove rear display unit (2).
INSTALLATION
Installation is the reverse order if removal.
Multifunction SwitchNKS004BY
REMOVAL
1. Remove instrument panel finisher B and C. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screw (A).
3. Disengage tabs (B) and connector to separate multifunction
switch (1) from instrument panel.
INSTALLATION
Installation is the reverse order of removal.
Preset SwitchNKS004BZ
REMOVAL
1. Remove cluster lid C. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
SKIB4354E
SKIB4355E
SKIB4276E

AV-294
[WITH MOBILE ENTERTAINMENT SYSTEM]
REMOVAL AND INSTALLATION
Revision: 2006 January2006 M35/M45
Rear Control SwitchNKS004C1
REMOVAL
1. Remove tray box from armrest. Refer to SE-167, "Removal and Installation" .
2. Remove screws (A).
3. Disconnect connector (1) and disengage tabs (A) to separate
rear control switch (2).
INSTALLATION
Installation is the reverse order of removal.
Video DistributorNKS004C2
REMOVAL
1. Remove multifunction switch. Refer to AV-292, "Multifunction Switch" .
2. Remove audio unit assembly. Refer to AV-285, "
Audio Unit" .
3. Remove screws (A).
4. Disconnect connector and remove video distributor (1).
5. Remove screws (A) and remove bracket (1).
SKIB4300E
SKIB4301E
SKIB4392E
SKIB4393E

AV-296
[WITH MOBILE ENTERTAINMENT SYSTEM]
REMOVAL AND INSTALLATION
Revision: 2006 January2006 M35/M45
Auxiliary Input JacksNKS004C4
REMOVAL
1. Remove center console rear finisher. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws (A) and disconnect connector. Remove auxil-
iary input jacks (1) from center console rear finisher.
INSTALLATION
Installation is the reverse order of removal.
Headphone AmpNKS004C5
: Vehicle front
REMOVAL
1. Remove rear display cover. Refer to IP-19, "Disassembly and Assembly" .
2. Remove nuts (A) and disconnect connector. Remove head-
phone amp (1).
INSTALLATION
Installation is the reverse order of removal.
MicrophoneNKS004C6
REMOVAL
1. Remove front pillar garnish. Refer to EI-37, "BODY SIDE TRIM" .
2. Remove sun-visor and sun-visor holder. Refer to EI-52, "
HEADLINING" .
3. Remove dual-sunvisor. Refer to EI-52, "
HEADLINING" .
4. Remove assistance grip (front). Refer to EI-52, "
HEADLINING" .
5. Bear down headlining assembly (front) to obtain work space between headlining assembly and vehicle.
6. Disengage tabs (A) and connector to separate microphone unit
(1).
SKIB4351E
SKIB4353E
SKIB4302E

AV-298
[WITH MOBILE ENTERTAINMENT SYSTEM]
REMOVAL AND INSTALLATION
Revision: 2006 January2006 M35/M45
Camera Control UnitNKS004C8
REMOVAL
1. Remove trunk side finisher (RH). Refer to EI-56, "Removal and Installation for Trunk Room Trim" .
2. Remove screws (A) and disconnect connector, and remove rear
view camera control unit (1).
3. Remove screws (A) and remove bracket (1).
INSTALLATION
Installation is the reverse order of removal.
Rear View CameraNKS004C9
REMOVAL
1. Remove trunk lid finisher inner. Refer to EI-56, "TRUNK ROOM TRIM & TRUNK LID FINISHER" .
2. Remove screws attaching camera and camera bracket.
3. Remove connector and connector clip.
4. Remove camera bracket (1) while pushing right direction of
vehicle.
INSTALLATION
1. Install rear view camera and camera bracket while pressing to trunk room side.
2. Install connector and connector clip.
3. Install trunk lid finisher inner.
SKIB4398E
SKIB4399E
SKIB5010E

HEADLINING
EI-53
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: 2006 January2006 M35/M45
REMOVAL
1. Remove front pillar garnish (LH/RH). Refer to EI-37, "BODY SIDE TRIM" .
2. Remove roof harness and antenna feeder securing clip using a clip clamp remover after removing front
pillar garnish (LH/RH), and then disconnect roof harness and antenna feeder connectors.
3. Remove rear seat cushion and seatback. Refer to SE-172, "
REAR SEAT" .
4. Remove front kicking plate inner, center pillar lower garnish, center pillar upper garnish, front body side
welt, rear kicking plate inner, rear wheelhouse garnish, rear pillar finisher, rear body side welt. Refer to EI-
37, "BODY SIDE TRIM" .
5. Disconnect antenna feeder connectors of antenna amplifier and
sub-antenna feeder after removing rear pillar finisher (LH), and
then remove antenna feeder securing clip using a remover.
6. Models with sunroof: Remove mounting plastic clips of front
assistance grip (LH/RH) and rear assistance grip (LH/RH), and
then remove bolts.
Models with standard roof: Remove mounting plastic clips of
front assistance grip (LH) and rear assistance grip (LH/RH).
CAUTION:
Always use SST, and attach a cloth to protect from dam-
age.
Assistance grip is crimped from back of headlining.
Remove it by disengaging the crimping area of back of
lamp after removing headlining from the vehicle.
7. Remove screws on personal lamp (in coat hanger hook).
8. Remove rear display unit. (models with mobile entertainment system) Refer to AV- 2 9 2 , "
Rear Display
Unit" .
9. Remove sun visor bracket cover and mounting screws, and then remove sun visors (LH/RH).
NOTE:
Disconnect vanity mirror illumination harness connector when removing sun visor.
10. Remove screws of dual-visor, and then remove dual-visor (LH/RH).
11. Insert a screwdriver into the sun visor holder cutout and rotate
90 degrees to remove sun visor holder (LH/RH).
12. Remove map lamp assembly. (models with LDW system)
13. Remove passenger seat assembly. Refer to SE-163, "
FRONT SEAT" .
14. Using a removal tool, remove body side mounting plastic clip from rear side of headlining.
PIIB4939E
PIIB3585J
SIIA0224J