2006 INFINITI M35 clutch

TROUBLE DIAGNOSIS - GENERAL DESCRIPTION
ACS-31
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2006 January2006 M35/M45
THRTL SENSOR
[deg]NOTE:
This item is displayed, but cannot monitor.
SET DISTANCE
[SHOR/MID/LONG]
Indicates set distance memorized in ICC sensor integrated unit.
MAIN SW
[ON/OFF]
Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
SET/COAST SW
[ON/OFF]
Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
CANCEL SW
[ON/OFF]
Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
RESUME/ACC SW
[ON/OFF]
Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
DISTANCE SW
[ON/OFF]
Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
CRUISE OPE
[ON/OFF]
Indicates whether controlling or not (ON means “controlling”).
BRAKE SW
[ON/OFF]
Indicates [ON/OFF] status as judged from ICC brake switch signal (ECM
transmits ICC brake switch signal through CAN communication).
STOP LAMP SW
[ON/OFF]
Indicates [ON/OFF] status as judged from stop lamp switch signal (ECM
transmits stop lamp switch signal through CAN communication).
CRUISE LAMP
[ON/OFF]
Indicates [ON/OFF] status of MAIN switch indicator lamp output.
CLUTCH SW SIG
[ON/OFF]
NOTE:
This item is displayed, but cannot monitor.
NP SW SIG
[ON/OFF]
NOTE:
This item is displayed, but cannot monitor.
STP LMP DRIVE
[ON/OFF]
Indicates [ON/OFF] status of ICC brake hold relay drive output.
PWR SUP MONI
[V]
Indicates IGN voltage input by ICC sensor integrated unit.
IDLE SW
[ON/OFF]
Indicates [ON/OFF] status of idle switch read from ICC sensor integrated
unit through CAN communication (ECM transmits ON/OFF status through
CAN communication).
OWN VHCL
[ON/OFF]
Indicates [ON/OFF] status of own vehicle indicator output.
VHCL AHEAD
[ON/OFF]
Indicates [ON/OFF] status of vehicle ahead detection indicator output.
ICC WARNING
[ON/OFF]
Indicates [ON/OFF] status of ICC system warning lamp output.
BUZZER O/P
[ON/OFF]
Indicates [ON/OFF] status of ICC warning chime output.
ENGINE RPM
[rpm]
Indicates engine speed read from ICC sensor integrated unit through CAN
communication (ECM transmits engine speed through CAN communica-
tion).
WIPER SW
[OFF/LOW/HIGH]
Indicates wiper [OFF/LOW/HIGH] status (BCM transmits front wiper request
signal through CAN communication).
YAW R AT E
[deg/s]
NOTE:
This item is displayed, but cannot monitor.
D RANGE SW
[ON/OFF]
Indicates [ON/OFF] status of “D” and “M” positions read from ICC sensor
integrated unit through CAN communication; ON when position “D” and “M”
(TCM transmits A/T position indicator lamp signal through CAN communi-
cation). Monitored Item [unit]MAIN
SIGNALSSELEC-
TION FROM
MENUDescription

AT-2Revision: 2006 January2006 M35/M45 On Board Diagnosis Logic ....................................113
Possible Cause .....................................................113
DTC Confirmation Procedure ...............................113
Wiring Diagram — AT — PNP/SW .......................114
Diagnostic Procedure ...........................................115
DTC P0717 TURBINE REVOLUTION SENSOR ....117
Description ............................................................117
CONSULT-II Reference Value ..............................117
On Board Diagnosis Logic ....................................117
Possible Cause .....................................................117
DTC Confirmation Procedure ...............................117
Diagnostic Procedure ...........................................118
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) ...............................................119
Description ............................................................119
CONSULT-II Reference Value ..............................119
On Board Diagnosis Logic ....................................119
Possible Cause .....................................................119
DTC Confirmation Procedure ...............................119
Wiring Diagram — AT — VSSA/T .........................121
Diagnostic Procedure ...........................................122
DTC P0725 ENGINE SPEED SIGNAL ...................124
Description ............................................................124
CONSULT-II Reference Value ..............................124
On Board Diagnosis Logic ....................................124
Possible Cause .....................................................124
DTC Confirmation Procedure ...............................124
Diagnostic Procedure ...........................................125
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE .................................................126
Description ............................................................126
CONSULT-II Reference Value ..............................126
On Board Diagnosis Logic ....................................126
Possible Cause .....................................................126
DTC Confirmation Procedure ...............................126
Diagnostic Procedure ...........................................127
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) . 128
Description ............................................................128
CONSULT-II Reference Value ..............................128
On Board Diagnosis Logic ....................................128
Possible Cause .....................................................128
DTC Confirmation Procedure ...............................128
Diagnostic Procedure ...........................................129
DTC P0745 LINE PRESSURE SOLENOID VALVE .130
Description ............................................................130
CONSULT-II Reference Value ..............................130
On Board Diagnosis Logic ....................................130
Possible Cause .....................................................130
DTC Confirmation Procedure ...............................130
Diagnostic Procedure ...........................................131
DTC P1705 THROTTLE POSITION SENSOR .......132
Description ............................................................132
CONSULT-II Reference Value ..............................132
On Board Diagnosis Logic ....................................132
Possible Cause .....................................................132
DTC Confirmation Procedure ...............................132
Diagnostic Procedure ...........................................133
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ..................................................................135Description ............................................................135
CONSULT-II Reference Value ...............................135
On Board Diagnosis Logic ....................................135
Possible Cause .....................................................135
DTC Confirmation Procedure ................................135
Wiring Diagram — AT — FTS ...............................136
Diagnostic Procedure ............................................137
Component Inspection ..........................................139
DTC P1721 VEHICLE SPEED SENSOR MTR .......140
Description ............................................................140
CONSULT-II Reference Value ...............................140
On Board Diagnosis Logic ....................................140
Possible Cause .....................................................140
DTC Confirmation Procedure ................................140
Diagnostic Procedure ............................................141
DTC P1730 A/T INTERLOCK .................................142
Description ............................................................142
On Board Diagnosis Logic ....................................142
Possible Cause .....................................................142
DTC Confirmation Procedure ................................142
Judgement of A/T Interlock ...................................143
Diagnostic Procedure ............................................143
DTC P1731 A/T 1ST ENGINE BRAKING ...............145
Description ............................................................145
CONSULT-II Reference Value ...............................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ................................145
Diagnostic Procedure ............................................146
DTC P1752 INPUT CLUTCH SOLENOID VALVE ..147
Description ...................................................
.........147
CONSULT-II Reference Value ...............................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ................................147
Diagnostic Procedure ............................................148
DTC P1754 INPUT CLUTCH SOLENOID VALVE
FUNCTION ..............................................................149
Description ............................................................149
CONSULT-II Reference Value ...............................149
On Board Diagnosis Logic ....................................149
Possible Cause .....................................................149
DTC Confirmation Procedure ................................149
Diagnostic Procedure ............................................150
DTC P1757 FRONT BRAKE SOLENOID VALVE ...151
Description ............................................................151
CONSULT-II Reference Value ...............................151
On Board Diagnosis Logic ....................................151
Possible Cause .....................................................151
DTC Confirmation Procedure ................................151
Diagnostic Procedure ............................................152
DTC P1759 FRONT BRAKE SOLENOID VALVE
FUNCTION ..............................................................153
Description ............................................................153
CONSULT-II Reference Value ...............................153
On Board Diagnosis Logic ....................................153
Possible Cause .....................................................153
DTC Confirmation Procedure ................................153
Diagnostic Procedure ............................................154

AT-3
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 January2006 M35/M45 DTC P1762 DIRECT CLUTCH SOLENOID VALVE .155
Description ...........................................................155
CONSULT-II Reference Value ..............................155
On Board Diagnosis Logic ...................................155
Possible Cause ....................................................155
DTC Confirmation Procedure ...............................155
Diagnostic Procedure ...........................................156
DTC P1764 DIRECT CLUTCH SOLENOID VALVE
FUNCTION ..............................................................157
Description ...........................................................157
CONSULT-II Reference Value ..............................157
On Board Diagnosis Logic ...................................157
Possible Cause ....................................................157
DTC Confirmation Procedure ...............................157
Diagnostic Procedure ...........................................158
DTC P1767 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE .................................................159
Description ...........................................................159
CONSULT-II Reference Value ..............................159
On Board Diagnosis Logic ...................................159
Possible Cause ....................................................159
DTC Confirmation Procedure ...............................159
Diagnostic Procedure ...........................................160
DTC P1769 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE FUNCTION .............................161
Description ...........................................................161
CONSULT-II Reference Value ..............................161
On Board Diagnosis Logic ...................................161
Possible Cause ....................................................161
DTC Confirmation Procedure ...............................161
Diagnostic Procedure ...........................................162
DTC P1772 LOW COAST BRAKE SOLENOID
VALVE .....................................................................163
Description ...........................................................163
CONSULT-II Reference Value ..............................163
On Board Diagnosis Logic ...................................163
Possible Cause ....................................................163
DTC Confirmation Procedure ...............................163
Diagnostic Procedure ...........................................164
DTC P1774 LOW COAST BRAKE SOLENOID
VALVE FUNCTION .................................................165
Description ...........................................................165
CONSULT-II Reference Value ..............................165
On Board Diagnosis Logic ...................................165
Possible Cause ....................................................165
DTC Confirmation Procedure ...............................165
Diagnostic Procedure ..........................................
.166
DTC P1815 MANUAL MODE SWITCH ..................167
Description ...........................................................167
CONSULT-II Reference Value ..............................167
On Board Diagnosis Logic ...................................167
Possible Cause ....................................................167
DTC Confirmation Procedure ...............................167
Wiring Diagram — AT — MMSW .........................168
Diagnostic Procedure ...........................................170
Component Inspection .........................................171
DTC P1841 ATF PRESSURE SWITCH 1 ...............172
Description ...........................................................172
CONSULT-II Reference Value ..............................172On Board Diagnosis Logic ....................................172
Possible Cause .....................................................172
DTC Confirmation Procedure ...............................172
Diagnostic Procedure ...........................................173
DTC P1843 ATF PRESSURE SWITCH 3 ...............174
Description ............................................................174
CONSULT-II Reference Value ..............................174
On Board Diagnosis Logic ....................................174
Possible Cause .....................................................174
DTC Confirmation Procedure ...............................174
Diagnostic Procedure ...........................................175
DTC P1845 ATF PRESSURE SWITCH 5 ...............176
Description ............................................................176
CONSULT-II Reference Value ..............................176
On Board Diagnosis Logic ....................................176
Possible Cause .....................................................176
DTC Confirmation Procedure ...............................176
Diagnostic Procedure ...........................................177
DTC P1846 ATF PRESSURE SWITCH 6 ...............178
Description ............................................................178
CONSULT-II Reference Value ..............................178
On Board Diagnosis Logic ....................................178
Possible Cause .....................................................178
DTC Confirmation Procedure ...............................178
Diagnostic Procedure ...........................................179
MAIN POWER SUPPLY AND GROUND CIRCUIT .180
Wiring Diagram — AT — MAIN ............................180
Diagnostic Procedure ...........................................181
CLOSED THROTTLE POSITION AND WIDE OPEN
THROTTLE POSITION CIRCUIT ............................184
CONSULT-II Reference Value ..............................184
Diagnostic Procedure ...........................................184
BRAKE SIGNAL CIRCUIT ......................................185
CONSULT-II Reference Value ..............................185
Diagnostic Procedure ...........................................185
A/T INDICATOR CIRCUIT .......................................186
Description ............................................................186
CONSULT-II Reference Value ..............................186
Diagnostic Procedure ...........................................186
TROUBLE DIAGNOSIS FOR SYMPTOMS ............187
Wiring Diagram — AT — NONDTC ......................187
A/T CHECK Indicator Lamp Does Not Come On . 190
Engine Cannot Be Started in “P” or “N” Position ..190
In “P” Position, Vehicle Moves When Pushed ......191
In “N” Position, Vehicle Moves ..............................192
Large Shock (“N” to “D” Position) .........................193
Vehicle Does Not Creep Backward in “R” Position .195
Vehicle Does Not Creep Forward in “D” Position . 197
Vehicle Cannot Be Started from D
1 ......................199
A/T Does Not Shift: D
1 D2 ................................201
A/T Does Not Shift: D
2 D3 ................................203
A/T Does Not Shift: D
3 D4 ................................205
A/T Does Not Shift: D
4 D5 ................................207
A/T Does Not Lock-Up ..........................................209
A/T Does Not Hold Lock-Up Condition .................210
Lock-Up Is Not Released ......................................212
Engine Speed Does Not Return to Idle ................212
Cannot Be Changed to Manual Mode ..................213
A/T Does Not Shift: 5th Gear
4th Gear ............214

AT-4Revision: 2006 January2006 M35/M45 A/T Does Not Shift: 4th Gear
3rd Gear ............215
A/T Does Not Shift: 3rd Gear
2nd Gear ...........217
A/T Does Not Shift: 2nd Gear
1st Gear ............218
Vehicle Does Not Decelerate by Engine Brake ....220
SHIFT CONTROL SYSTEM ....................................222
Control Device Removal and Installation ..............222
Control Rod Removal and Installation ..................226
Adjustment of A/T Position ...................................227
Checking of A/T Position ......................................228
A/T SHIFT LOCK SYSTEM .....................................229
Description ............................................................229
Shift Lock System Electrical Parts Location .........229
Wiring Diagram — AT — SHIFT ...........................230
Diagnostic Procedure ...........................................232
ON-VEHICLE SERVICE ..........................................236
C o n t r o l V a l v e W i t h T C M a n d A / T F l u i d Te m p e r a t u r e
Sensor 2 ...............................................................236
Parking Components (2WD Models Only) ............248
Rear Oil Seal (VQ35DE Models Only) ..................260
Revolution Sensor Components (2WD Models
Only) .....................................................................261
AIR BREATHER HOSE ...........................................269
Removal and Installation ......................................269
TRANSMISSION ASSEMBLY ................................271
Removal and Installation (2WD Models) ..............271
Removal and Installation (AWD Models) ..............275
OVERHAUL .............................................................278
Components .........................................................278Oil Channel ...........................................................292
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................295
DISASSEMBLY .......................................................298
Disassembly ..........................................................298
REPAIR FOR COMPONENT PARTS ......................318
Oil Pump ...............................................................318
Front Sun Gear, 3rd One-Way Clutch ...................321
Front Carrier, Input Clutch, Rear Internal Gear .....323
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ..............................................329
High and Low Reverse Clutch ..............................335
Direct Clutch .........................................................337
ASSEMBLY .............................................................340
Assembly (1) .........................................................340
Adjustment ............................................................356
Assembly (2) .........................................................358
SERVICE DATA AND SPECIFICATIONS (SDS) ....365
General Specifications ......................................... .365
Vehicle Speed at Which Gear Shifting Occurs ......365
Vehicle Speed at Which Lock-Up Occurs/Releases .366
Stall Speed ............................................................366
Line Pressure ........................................................366
A/T Fluid Temperature Sensor ..............................366
Turbine Revolution Sensor ....................................367
Vehicle Speed Sensor A/T (Revolution Sensor) ...367
Reverse Brake ......................................................367
Total End Play .......................................................367

PRECAUTIONS
AT-9
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 January2006 M35/M45
Clean or replace ATF cooler if excessive foreign material is found in oil pan or clogging strainer. Refer to
AT- 9 , "
ATF COOLER SERVICE" .
After overhaul, refill the transmission with new ATF.
When the A/T drain plug is removed, only some of the ATF is drained. Old ATF will remain in torque con-
verter and ATF cooling system.
Always follow the procedures under “Changing A/T Fluid” in the AT section when changing A/T fluid. Refer
to AT- 1 2 , "
Changing A/T Fluid" , AT- 1 3 , "Checking A/T Fluid" .
Service Notice or PrecautionsNCS001JF
ATF COOLER SERVICE
If ATF contains frictional material (clutches, bands, etc.), or if an A/T is repaired, overhauled, or replaced,
inspect and clean the A/T fluid cooler mounted in the radiator or replace the radiator. Flush cooler lines using
cleaning solvent and compressed air after repair. For A/T fluid cooler cleaning procedure, refer to AT- 1 4 , "
A/T
Fluid Cooler Cleaning" . For radiator replacement, refer to CO-14, "RADIATOR" (for VQ35DE engine), CO-43,
"RADIATOR" (for VK45DE engine).
OBD-II SELF-DIAGNOSIS
A/T self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through
the blinking pattern of the A/T CHECK indicator or the malfunction indicator lamp (MIL). Refer to the table
on AT- 9 2 , "
SELF-DIAGNOSTIC RESULT MODE" for the indicator used to display each self-diagnostic
result.
The self-diagnostic results indicated by the MIL are automatically stored in both the ECM and TCM mem-
ories.
Always perform the procedure on AT- 4 1 , "
HOW TO ERASE DTC" to complete the repair and avoid
unnecessary blinking of the MIL.
For details of OBD-II, refer to EC-54, "
ON BOARD DIAGNOSTIC (OBD) SYSTEM" (for VQ35DE engine), EC-
764, "ON BOARD DIAGNOSTIC (OBD) SYSTEM" (for VK45DE engine).
Certain systems and components, especially those related to OBD, may use the new style slide-
locking type harness connector. For description and how to disconnect, refer to PG-102, "
HAR-
NESS CONNECTOR" .

AT-10
PREPARATION
Revision: 2006 January2006 M35/M45
PREPARATIONPFP:00002
Special Service ToolsNCS001JG
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool nameDescription
ST2505S001
(J-34301-C)
Oil pressure gauge set
1. ST25051001
(—)
Oil pressure gauge
2. ST25052000
(—)
Hose
3. ST25053000
(—)
Joint pipe
4. ST25054000
(—)
Adapter
5. ST25055000
(—)
AdapterMeasuring line pressure
KV31103600
(J-45674)
Joint pipe adapter
(With ST25054000)Measuring line pressure
ST33400001
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
Installing rear oil seal (VQ35DE models for 2WD)
Installing oil pump housing oil seal
KV31102400
(J-34285 and J-34285-87)
Clutch spring compressor
a: 320 mm (12.60 in)
b: 174 mm (6.85 in)Installing reverse brake return spring retainer
ST25850000
(J-25721-A)
Sliding hammer
a: 179 mm (7.05 in)
b: 70 mm (2.76 in)
c: 40 mm (1.57 in)
d: M12X1.75PRemove oil pump assembly
SCIA3695J
ZZA1227D
NT086
NT423
NT422

AT-14
A/T FLUID
Revision: 2006 January2006 M35/M45
CAUTION:
When wiping away the A/T fluid level gauge, always use lint-free paper, not a cloth one.
To check A/T fluid level, insert the A/T fluid level gauge
until the cap contacts the end of the A/T fluid charging
pipe, with the A/T fluid level gauge reversed from the nor-
mal attachment conditions as shown.
8. Check A/T fluid condition.
If ATF is very dark or smells burned, check operation of A/T.
Flush cooling system after repair of A/T.
If A/T fluid contains frictional material (clutches, bands, etc.),
replace radiator and flush cooler line using cleaning solvent
and compressed air after repair of A/T. Refer to CO-14,
"RADIATOR" (for VQ35DE engine), CO-43, "RADIATOR"
(for VK45DE engine) and AT- 1 4 , "A/T Fluid Cooler Cleaning" .
9. Install the removed A/T fluid level gauge in the A/T fluid charging
pipe.
10. Tighten level gauge bolt.
A/T Fluid Cooler CleaningNCS001JK
Whenever an A/T is replaced, the A/T fluid cooler mounted in the radiator must be inspected and cleaned.
Metal debris and friction material, if present, can become trapped in the A/T fluid cooler. This debris can con-
taminate the newly serviced A/T or, in severe cases, can block or restrict the flow of ATF. In either case, mal-
function of the newly serviced A/T may result.
Debris, if present, may build up as ATF enters the cooler inlet. It will be necessary to back flush the cooler
through the cooler outlet in order to flush out any built up debris.
A/T FLUID COOLER CLEANING PROCEDURE
1. Position an oil pan under the A/T inlet and outlet cooler hoses.
2. Identify the inlet and outlet fluid cooler hoses.
3. Disconnect the A/T fluid cooler inlet and outlet rubber hoses
from the steel cooler tubes or bypass valve.
NOTE:
Replace the cooler hoses if rubber material from the hose
remains on the tube fitting.
4. Allow any ATF that remains in the cooler hoses to drain into the
oil pan.Level gauge bolt
: 5.1 Nꞏm (0.52 kg-m, 45 in-lb)
SCIA2899E
SCIA4896E
SCIA3830E

AT-16
A/T FLUID
Revision: 2006 January2006 M35/M45
5. Tie a common white, basket-type coffee filter to the end of the
cooler inlet hose.
6. Insert the tip of an air gun into the end of the cooler outlet hose.
7. Wrap a shop rag around the air gun tip and end of cooler outlet
hose.
8. Blow compressed air regulated to 5 to 9 kg/cm
2 (70 to130 psi)
through the cooler outlet hose to force any remaining ATF into
the coffee filter.
9. Remove the coffee filter from the end of the cooler inlet hose.
10. Perform AT- 1 6 , "
A/T FLUID COOLER INSPECTION PROCE-
DURE" .
A/T FLUID COOLER INSPECTION PROCEDURE
1. Inspect the coffee filter for debris.
a. If small metal debris less than 1mm (0.040 in) in size or metal
powder is found in the coffee filter, this is normal. If normal
debris is found, the A/T fluid cooler/radiator can be re-used and
the procedure is ended.
b. If one or more pieces of debris are found that are over 1 mm
(0.040 in) in size and/or peeled clutch facing material is found in
the coffee filter, the A/T fluid cooler is not serviceable. The A/T
fluid cooler/radiator must be replaced and the inspection proce-
dure is ended. Refer to CO-14, "
RADIATOR" (for VQ35DE
engine), CO-43, "
RADIATOR" (for VK45DE engine).
A/T FLUID COOLER FINAL INSPECTION
After performing all procedures, ensure that all remaining oil is cleaned from all components.
SCIA3833E
SCIA3834E
SCIA2967E
SCIA7031E