2006 GREAT WALL SO COOL wheel bolt torque

BR-26
Rear brake
Element figure
wheel-brake cylinder cluster
pressure spring drag rod
self clearance-
adjusting bracing
wireparking brake arm
flat washer
split pinbrake shoe gear
return spring
parking brake push plate
push-plate spring back brake
shoe
self clearance-
adjusting toggle
tension spring
brake drum
clearance adjuster
pressure spring seatpressure spring front brake shoe
Disassembly of Rear drum-type Brake
Remark: if the braking torque of manual brake cannot satisfies
the braking requirement, it is suggested to check the thickness
of brake shoe liner, where the thickness is less than the min
thickness, change the brake shoe.
Min thickness
1.0mm
1. Tear down the rear wheel;
2. Tear down the brake drum;
Remark: in case the brake drum is not easy to tear down, the
following steps shall be adapted:
(a) Tear down the clearance-adjusting hole; insert a screw-
driver in the brake bottom plate hole to prize up the
adjusting bolt inner tilt angle with the self-adjusting fork.
(b) Use another screwdriver to adjust the adjusting bolt inner
tilt angle to loosen the clearance adjuster of brake shoe. DrBraking System
Rear Brake (Dr)

Parts that cannot be reused after being used

BR-30
Assembly of Rear Brake
remark: assemble the parts according to the
direction in the drawing;
left wheel
right wheel forward
1. Assemble the wheel-brake cylinder:
(a) Coat moderate lithium soap base glycol grease on the
piston cup;
(b) Assemble the wheel-brake cylinder:

Mount the two piston cups on two piston;

Encase the spring and two pistons in the wheel cylinder
body and

Mount the two dust covers
Remark: Assembly shall be conducted correctly according to
the direction shown in the drawing.
2. Mount the wheel-brake cylinder:
(a) Use two bolts to fix the wheel-brake cylinder on the rear
bottom plate.
Coat moderate sealing glue (Glue 704) on the position where
the wheel-brake cylinder connects with the bottom plate.
Fastening torque
(16
20)N
m
(c) Connect the brake pipeline on the wheel-brake cylinder.
Fastening torque
18N
m
3. Coat the following parts with moderate lubricant that
resistant high temperature (do not pollute the friction
plates);
(a) The upper plain of the hex convex platform where the
bottom plate connects the brake shoe;
(b) Contact face of the brake shoe and the top lever of wheel
cylinder;
(c) Contact face of the brake shoe with the support pin. Braking System
Rear Brake (DR)
Assembly of Rear Brake
forward

BR-38
Assembly of Rear Brake
left wheel
right wheelforward forward
1. Assemble the wheel-brake cylinder:
(a) Coat moderate lithium soap base glycol grease on the
piston cup.
(b) Assembly the wheel-brake cylinder

Mount the two piston cups on two pistons

Mount the two dust cover on two pistons.

Encase the spring and the two pistons in the wheel
cylinder body.
Remark: assembly correctly according to the direction shown
in the drawing.
2. Mount the wheel-brake cylinder:
(a) Mount the wheel-brake cylinder on the rear bottom plate
with two bolts.
Fastening torque
(6.5
10)N

m
(b) Connect the brake pipeline on the wheel-brake cylinder.
Fastening torque
(18+2)N

m
3. Coat the lithium base grease on the following parts:
(a) Hex convex platform where the bottom plate contacts
with the brake shoe.
(b) Two ends of support brocks
(c) Contact position where the piston and the shoe rib.
Remark: Do not pollute the friction pads. Braking System
Rear Brake (SF)
remark: assemble the component elements in the direction shown in the drawing;

SR-20Steering system - Steering Linkage
Steering Linkage
Dismantle and mount of steering linkage
N
m
specified torque

Parts that cannot be reused after being used
side drag rod assembly
joint clip






intermediate lateral drag rod assembly






auxiliary steering arm
80
10(Dr)
83
10(SL SK SY)
142
10(SF)
78
10(SJ)
91
10(Dr)
59
5(SF)
91
10(Dr SF)
90
10(SL SK SY)
78
10(SJ)
Remark
(a) Where the bolts of recirculating ball are connected with
the arm or lever, the lubricant on its surface should be
cleaned.
(b) Screw up the bolts and nuts of re-circulating ball to the
specified torque, and then screw the nut forward to the
degree that the split pin can be encased in.
(c) Check the Alignment of Front Wheel and side slip after
any part of steering linkage is mounted.

A-2
Clutch
Specification
Item Specification
Fastening torque for clutch tube on master cylinder
Fastening torque for clutch tube on wheel-brake cylinder
Fastening torque for clutch pressure plate160
190-200
5-15
0.3
0.8
0.2
0.6
5
Max misplacement
0.5 Pedal height (calculated from front wall
Pedal free stroke
Min depth of clutch-facing rivet
Max radial swing difference of clutch rib
Max radial swing difference of flywheel
Max width of wear of diaphragm spring
Max width of wear of diaphragm spring
Alignment degree of diaphragm spring endApplicable vehicle model
Dr SF
SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Torsion moment
Fastening location (N*m)
15-17
15-17
30 Applicable Vehicle model
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Gearbox
Three-grade maintenance for gearbox
1. Grade I maintenance for gear box
Grade I maintenance: Check the lubricant level to see whether the lubricant level is in alignment with the lower edge of oil
filler; if the lubricant is lower than the oil filler lower edge, add the lubricant; or the insufficient lubricant will lead to the poor
lubrication or burn-out of bearing and teeth; while the over-high lubricant will cause the overheating and oil leakage.
2. Grade II maintenance for gear box
Grade II maintenance: The gear box of a new vehicle should be maintained by exchanging the lubricant during the
first grade II maintenance and should be washed with kerosene; and the lubricant quality should be checked in the
grade II maintenance in later time, if the lubricant is diluted, gumming or over-dirty, it should be changed.
3. Grade III maintenance
The gearbox should be disassembled for inspection, washing and oil change.
Notice: As the new vehicle is in the running-in status, the gearbox should be maintained by exchanging lubricant
after the vehicle covers 1500 km,
Lubricant Type
GL-5 SAE80W/90
Torsion moment of relative connecting elements
Tung Teeth: Tang tooth(5DYA4TWD
5DYA8FWD)
Unit
ãã Specification of Maintenance and Up-Keeping
Clutch and Gearbox
Locating screw of fork axle at first and second gear
Locating screw of yoke block
Screw on baffle of rear bearing of output shaft
Screw of reverse idler shaft
Bolt of gearshift cover
Bolt of front cover
Bolt of rear body
Bolt of clutch shell
Bolt of locating spring13
17
15
20
17
22
17
20
15
20
15
20
30
45
30
45
17
22 Fastening location N*m