2006 GREAT WALL HOVER transmission

Automatic transmission-26
Power transmission
Introduction
It has the following power transmission pointed to different Gear-position:
power transmission N-Gear and P-Gear
power transmission R-Gear
power transmission manual 1
power transmission Automatic 1st-Gear
power transmission Automatic 2nd -Gear
power transmission Automatic 3rd -Gear
power transmission Automatic 3rd-Gear locking
power transmission Automatic 4th -Gear (overspeed -gear)
power transmission Automatic 4th -Gear locking
For description of each kind of power transmission condition, refer to following parts.
Table 5.1 describe the on-off condition of each unit in all gear condition.
Name of participated unit
Position C1 C2 C3 C4 B1 B2 1-2
OWC 3-4
OWC LU
clutch
Parking and neutral position － － － － － X － － －
Reverse － － X － X － － －
Manual 1st -G ear － X － X － X － X
Automatic 1st- Gear － X － － － － X －
Auto 2nd-Gear and manual
2nd -G ear － X － X X － － X － Automatic 3rd –Gear and
manual 3rd-Gear X X － X － － － X － Automatic 3rd-Gear locking
and manual 3rd-Gear
locking X X － X － － － X X
Automatic 4th -Gear
(overspeed -gear) X X － － X － － － －
Automatic 4th -Gear locking
X X － － X － － － X
In P-Gear or N-Gear, the planetary gear assembly has not the drive. The rear brake belt is used to eliminate the voice generated in
engagement with reverse gear and increase the application of 4WD. It is without the engagement of clutch and brake belt.
In parking-Gear, the locking of mechanism is realized through the engagement of brake lever installed on housing and tooth of
output shaft gear ring.
Control
In stabl
e status, to maintain the arrangement, the status of solenoid valve and valve is shown as follows:
solenoid valve S1 and S2 is powered off.
The line (pump) pressure is applied on the primary regulating valve (PRV) and electromagnetic supply valve.
The torque converter, oil cooler and lubrication loop are filled up with the transmission fluid from the primary regulating
valve.
The line pressure 500 loop is filled up with the transmission fluid from the electromagnetic supply valve.

S5 will be filled up with the transmission fluid through the variable pressure

egulating valve (S5) .
The line pressure is prohibited form entering into the drive loop through the manual-operated valve .
B1 loop and all clutch loop are opened to drainage port.

Automatic transmission-27
Refer to Figure 5.1and table 5.2.
Table 5.2 The participation status of each unit in parking and neutral position
clutch
Gear-position
Name of participated unit
Parking and neutral
position

Automatic transmission-28
Figure 5.1 parking and neutral position

Automatic transmission-29
In reverse-Gear position, the drive of transmission is sent to the clutch hub through the input shaft and rear clutch piston. In this
condition, the description of each function unit of transmission is shown as follows:
The clutch C3 is engaged and drive the reverse central gear to rotate in clockwise.
The engagement of B2 brake belt cause the rest of the planetary gear carrier, then make the long planetary gear rotates
around its shaft anticlockwise.
The long planetary gear drives the internal gear ring rotates anticlockwise .
Use the spline to connect the inner gear ring to the output shaft and drive the gear ring rotate anticlockwise or in reverse.
Control:
In stable status, to maintain the arrangement, the action of solenoid valve and valve is shown as follows:
A solenoid valve S1 or S2 is closed at least. (Refer to the part in section 3.3.11, related to condition when S1 and S2 is
closed.)
The line pressure reaches the internal surface and external surface of rear servo piston through the reverse lock valve
directly.
The line pressure urges the reverse-Gear loop oil pass through the manual-operated valve.
The reverse-Gear loop oil is circuited to clutch C3 through the manual-operated valve.
In the transmission whiteout HP pump shell, the reverse-Gear loop also can reaches the spring end of the primary
regulating valve to support the spring and push the line-pressure regulating valve.
The oil loop of execution line of all other clutches and brake belts is opened to leaking port.
Refer to Figure 5.2 and Table 5.3.
Table 5.3 The participating condition of each unit in reverse-Gear position
Gear-position
Reverse gear
Name of participated unit

Automatic transmission-30
Figure 5.2 Reverse-Gear

Automatic transmission-31
Power transmission manual 1st-Gear
In manual 1st –Gear, the drive of transmission is send to the rear clutch cylinder through the input shaft. In this
condition, each function unit of transmission is shown as follows:
The clutch C2 is engaged through the 3-4 one-way clutch (OWC) to drive the front sun gear.
The engagement of B2 brake belt make the planetary gear carrier to stop.
The front sun gear drive the short planetary gear to rotate in anticlockwise.
The short planetary gear drive the long planetary gear to rotate in clockwise.
The long planetary gear rotate around its axial to drive the internal gear ring and output
shaft to rotate in clockwise to realize the movement in forward direction.
In overspeed, clutch C4 can provides certain brake force through 3-4 one-way clutch .
Control:
In stable status, the action of solenoid valve and valve is shown as follows:
The solenoid valve S1 and S2 is powered on.
In the action of pressure of line 500, the gear shift valve of 1-2, 2-3, 3-4 gear are kept in position of 1st-Gear.
The manual-operated valve transmission fluid (line pressure ) makes the clutch C2 to engagement.
LO-1st (line pressure) oil flows to the clutch C4 through the 1-2 Gear switching valve to engage the B2 brake belt.
Refer to Figure 5.3 and Table 5.4.
Table 5.4
The participating condition of each unit in manual 1st-Gear
Name of participated unit
X X

Automatic transmission-32
Figure 5.2 Reverse-Gear

Automatic transmission-33
Power transmission automatic 1st-Gear
In automatic 1st -Gear, the drive of transmission reaches the reaches the front clutch cylinder through the input shaft.
In this condition, the operating principle of each function unit of transmission is shown as follows:
The engagement of clutch C2 drives the front sun gear
The front sun gear drive the short planetary gear to rotate in anticlockwise.
The short planetary gear drives the long planetary gear to rotates in clockwise.
1-2 one-way clutch (OWC) stops the rotation of planetary gear carrier in counteracting force. At the same time, the long
planetary gear rotates around its axial to drive the ring gear and output shaft to rotate in clockwise to realize the forward
movement.
Control:
In stable status, the status of solenoid valve and valve is shown as follows:
Solenoid valve S1and S2 is powered on
In the action of line 500 pressure, the gear shift valve of 1-2, 2-3, 3-4 Gear is maintained in 1st-gear position.
The transmission drive oil (line pressure) from the manual-operated valve makes the engagement of clutch C2.
Table 5.5—participating condition of each unit in automatic 1st-Gear
Name of participation unit
Gear position
Automatic 1st-Gear
Refer to Figure 5.4and Table 5.5.