2006 BMW MOTORRAD K 1200 S reset

and cycles through the follow-
ing sequence:Total distance covered
Tripmeter 1 (Trip I)
Tripmeter 2 (Trip II)Resetting tripmeterSwitch on the ignition.
Select the desired tripmeter.
Press and hold down
button 1until the reading
changes.
The tripmeter is reset to
zero.
Residual rangeThe residual-range readout 1
indicates how far you can ride
with the fuel remaining in the
tank. On a motorcycle not
equipped with an on-board
computer, this reading is not
displayed until fuel level has
dropped to reserve. This dis-
tance is calculated on the
basis of fuel level and average
consumption.
When you refuel, the increase
in fuel level is not registered
unless several litres are ad- ded to the fuel already in the
tank.
The residual range is
only an approximate
reading. Consequently, BMW
Motorrad recommends that
you should not try to use the
full residual range before
refuelling.
ClockSet the clock
Attempting to set the
clock while riding the
motorcycle can lead to ac-
cidents.
Set the clock only when the
motorcycle is stationary.
Switch on the ignition.
442zOperation

The on-board computer's dis-
play field starts with the cur-
rent value and cycles through
the following sequence:Ambient temperature
Average speed
Average consumption
Range
Oil level
Tyre pressures (OE)
Ambient temperatureAmbient-temperature dis-
play 1is active only when
the engine is running; at other
times the display shows
---
.
An ice warning
appears if the ambient-
temperature reading drops
below 3 °C. The display
automatically switches
from any other mode to the
temperature reading when the
temperature drops below this
threshold for the first time.
The reading flashes until you select some other display
mode.
Calculating average
speedAverage speed
1is calculated
on basis of the time elapsed
since the last RESET. Times
during which the engine was
stopped are excluded from
the calculation.
445zOperation

Resetting average speedRepeatedly press INFO
button1until the average
speed appears in the
display.
Press and hold down the
INFO button until the read-
ing changes ("RESET").
The display shows
"--- km/h"
Calculating average
consumptionAverage consumption 1is
calculated by dividing the dis-
tance covered since the last
RESET by the corresponding
amount of fuel used.
Reset average
consumptionRepeatedly press INFO but-
ton 1until the average fuel
consumption appears in the
display.
Press and hold down the
INFO button until the read-
ing changes ("RESET").
The display shows
"--.- l/100 km".
446zOperation

M
MaintenanceGeneral instructions, 88
Intervals, 147
Multifunction display, 17, 20
O
Odometer and tripmeters, 20 Operation, 41
Pushbutton, 15
Resetting tripmeter, 42
Selecting readings, 41
On-board computer Ambient temperature, 45
Average consumption, 46
Average speed, 45
Oil level, 47
Pushbutton, 15
Range, 47
Reset average consump-
tion, 46
Resetting average
speed, 46
Selecting readings, 44 P
Power socket, 11, 13
Pre-ride check, 67
R
Rear-wheel stand
Installing, 107
Refuelling, 71
Reserve Warning, 24
Residual range, 42
Restoring to use, 129
Rev. counter, 17
Rims Test, 97
Running gear
Technical data, 139
S
Seat Installation, 54
Lock, 11, 13
Removal, 53
Service, 146
Service Card, 147 Side stand
Starting the engine, 66
Spark plugs, 142
Speedometer, 17
Spring preload, rear Adjusting, 11, 13, 57
Starter, 16
Steering lock, 39
Suspension damping, rear Adjusting, 11, 13, 58
T
Technical data Battery, 141
Brakes, 140
Bulbs, 142
Clutch, 137
Electrics, 141
Engine, 134
Engine oil, 136
Final drive, 139
Frame, 143
Fuel, 135
Running gear, 139
Spark plugs, 142
11158zIndex