2006 BMW 7 SERIES Advanced DVD System With Multimedia Changer Retrofit Instalation Instruction Manual

Downloaded from www.Manualslib.com manuals search engine 17 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
6. To install the connection cable and multimedia changer
Connect branch B3 to branch J2.
Connect branch C2 to branch L4.
Secure multimedia changer L to spacer plate P
using hexagonal screw R.
Secure multimedia changer L to spacer plate P
using hexagonal screw R and countersunk
screw Q
Secure AV switcher U to mounting plate O using
hexagonal nuts Y.
E60
E60
E61
E65E65 E61L
E61R
L4
C2
J2B3
065 0666 Z
L
P
R


 
R
Q
P
L
065 0640 Z
O
Y
Y
U


 

Downloaded from www.Manualslib.com manuals search engine 18 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
6. To install the connection cable and multimedia changer
Secure headphone module holder AW to front
module holder AY and rear module holder AZ
using hexagonal screws R.
Secure mounting plate O to headphone module
holder AW using hexagonal nuts AX.
Connect branches B2, C1, D3, D4, E3 and E4
to the cables of the same colour on the AV
switcher U.
Route branches A2 and A4 to the right-hand side
of the boot.
R
R
AW
AZAY
065 0667 Z
O
AX
AW
AX
065 0668 Z
U
D4
C1B2
D3
E3E4
065 0642 Z
A2/A4
065 0669 Z

Downloaded from www.Manualslib.com manuals search engine 19 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
6. To install the connection cable and multimedia changer
Connect branch A2, RT cable, to B+
distributor (1).
Secure the fusible link holder (2) to the standard
cable using a cable tie AP.
Connect branch A4, VI/WS cable, to
plug X1856, PIN 17, RT/GE cable, using
miniature connector AU.
Use hexagonal screws R to secure cover BA.
Affix information sticker AM in the glove
compartment (1).
A2
A4AU
1
X1856
AP
2


 
BA
R


 
1
AM


 

Downloaded from www.Manualslib.com manuals search engine 20 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
7. To install the fan cable (cars without an additional fan in the boot only)
Route branches I4and I6 to the right-hand side of
the boot.
Connect branch I4 to the control module holder (1).
Connect relay BF to branch I4.
Connect branch I5, RT/BL cable, to PIN 1 of plug
X4844, 5-pin SW.
Connect branch I6, GE/RT cable, to PIN 18 of
plug X1856, 32-pin SW.
If pin chamber 18 is occupied, use a mini-
ature connector AU to connect branch I6
to the GE/RT cable from PIN 18.

Insert fusible link BG into slot 71.
I4-I6
065 0740 Z
1I4
I5
BF
X4844


 
X1856
AU
BG
I6


 

Downloaded from www.Manualslib.com manuals search engine 21 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
8. To install the monitor
Slide the seat backrest cover (1) upwards.
Enlarge the existing holes (2) using a 9.1 mm
twist drill bit.
Insert rivet nuts AG.
Secure spacer bolts X to the seat backrest (1) with
one washer each AN and spacer bolts V to the
seat backrest (1) with
four washers each AN.
Move the seat cover (2) to its initial position.
Cut the seat cover (2) around the spacer bolts
using a knife.
Secure the monitor AA to the seat backrest (1)
using Torx screws Z.
The distance form the top of the monitor support
plate (2) to the headrest (3) must be approx. 10 mm.
The distance can be adjusted by removing
the washers AN or replacing the spacer
bolts V with spacer bolts W. At least one washer
AN must be fitted for each spacer bolt V or W.

Unscrew the monitor AA again
Cars without SA 456 only
Mark the hole at marking (1) on the inside of the
front seat rear panel (2) using the dimensions
shown.
Drill the hole using a 30 mm step drill.
2
1
   
 
AGAG 
X
VV
1
2
AN




2
1
3AA
Z
Z



13 mm
 30 mm2
1
060 0607 Z

Downloaded from www.Manualslib.com manuals search engine 22 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
8. To install the monitor
Cars with SA 456 only
Mark the hole at marking (1) on the inside of the
front seat rear panel (2) using the dimensions
shown.
Drill the hole using a 30 mm step drill.
All cars
Place the rear monitor trim AC on the top edge
(1) of the outside of the front seat rear panel (2).
The hole (3) in the rear of the monitor trim AC
must line up with the hole (4) in the front seat rear
panel.
Mark the holes (5) and drill them using as 15 mm
step drill.
Measure the dimensions of branch F2.
Push fabric hose AF over seat wiring harness F
and secure it with adhesive tape using the
dimensions shown.
Affix the marking (1) with adhesive tape using the
dimensions.
2 mm
 30 mm2
1
060 0770 Z
2
55
43
1
AC


 

 
 
1FAFF2
  

Downloaded from www.Manualslib.com manuals search engine 23 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
8. To install the monitor
As you install the seat wiring harness F check for sharp edges, reworking the edges if necessary.
After installation check that the seat wiring harness F moves easily when the backrest is adjusted.
The fitted fabric hose AF must be within the adjustment range of the backrest.

Route branches F1 and F2 as shown.
Route seat wiring harness F along the seat wiring harness (1).
1
F
F1/F2
AF



 

Downloaded from www.Manualslib.com manuals search engine 24 © BMW AG, München 01 29 0 406 372 12.2005 (Z/Z)
8. To install the monitor
Secure the adhesive marking (1) that you pre-
viously fitted on the seat wiring harness F to the
seat backrest (2) as shown using a cable tie AP.
Thread branches F1 and F2 through the front
seat rear panel (1).
Install the front seat rear panel (1) as described in
TISRA5215198.
Unscrew the tooth washer (1) and hexagonal nut (2)
from the auxiliary cable
G and headphone cable H.
Insert the auxiliary cable G into the front monitor
trim AT on the left and secure it with a toothed
washer (1) and hexagonal nut (2).
Insert the headphone cable H into the front
monitor trim AT on the right and secure it with a
toothed washer (1) and hexagonal nut (2).
Insert grommets AL into the monitor AA.
Thread headphone connector AA1 for the
monitor AA through the top grommet AL.
Insert cable ties AP into the existing holes.
1
21
F
APAP



 
1
F2
F1


 
21G
HAT


 
ALAP
AA1
AP
AA