2006 ACURA CSX coolant

•••Ó
Ó
•••
•••
•••
••• Ó
•••
••• Ó
•••
•••
•••
••• Ó
Ó
Ó
Ó
•••
••• Ó
••• ÓÓ
••• Ó
Ó
•••
••• Ó
Ó
Ó
Ó
Ó
(#')
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-9
DTC Troubleshooting Index
P0010 (56)
Variable Valve Timing Control (VTC) Oil Control Solenoid Valve
Malfunction ON (see page 11-274)
P0011 (56) Variable Valve Timing Control (VTC) System Malfunction ON (see page 11-276)
P0101 (50) Mass Air Flow (MAF) Sensor Circuit Range/Performance Problem ON (see page 11-74)
P0102 (50) Mass Air Flow (MAF) Sensor Circuit Low Voltage ON (see page 11-75)
P0103 (50) Mass Air Flow (MAF) Sensor Circuit High Voltage ON (see page 11-78)
P0107 (3) Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage ON (see page 11-80)
P0108 (3) Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage ON (see page 11-82)
P0111 (10) Intake Air Temperature (IAT) Sensor Circuit Range/Performance
Problem ON (see page 11-85)
P0112 (10) Intake Air Temperature (IAT) Sensor Circuit Low Voltage ON (see page 11-86)
P0113 (10) Intake Air Temperature (IAT) Sensor Circuit High Voltage ON (see page 11-87)
P0116 (86) Engine Coolant Temperature (ECT) Sensor 1 Circuit Range/
Performance Problem ON (see page 11-90)
P0117 (6) Engine Coolant Temperature (ECT) Sensor 1 Circuit Low Voltage ON (see page 11-91)
P0118 (6) Engine Coolant Temperature (ECT) Sensor 1 Circuit High Voltage ON (see page 11-92)
P0122 (7) Throttle Position (TP) Sensor A Circuit Low Voltage ON (see page 11-232)
P0123 (7) Throttle Position (TP) Sensor A Circuit High Voltage ON (see page 11-234)
P0125 (86) Engine Coolant Temperature (ECT) Sensor 1 Malfunction/Slow
Responce ON (see page 11-95)
P0128 (87) Cooling System Malfunction ON (see page 11-96)
P0133 (61) Air Fuel Ratio (A/F) Sensor (Sensor 1) Malfunction/Slow Response ON (see page 11-97)
P0134 (41) Air Fuel Ratio (A/F) Sensor (Sensor 1) Heater System Malfunction ON (see page 11-98)
P0135 (41) Air Fuel Ratio (A/F) Sensor (Sensor 1) Heater Circuit Malfunction ON (see page 11-99)
P0137 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit Low Voltage ON (see page 11-104)
P0138 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit High Voltage ON (see page 11-106)
P0139 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Slow Response ON (see page 11-109)
P0141 (65) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Heater Circuit Malfunction ON (see page 11-110)
P0171 (45) Fuel System Too Lean ON (see page 11-113)
P0172 (45) Fuel System Too Rich ON (see page 11-113)
P0222 (7) Throttle Position (TP) Sensor B Circuit Low Voltage ON (see page 11-236)
P0223 (7) Throttle Position (TP) Sensor B Circuit High Voltage ON (see page 11-239)
P0300 (75)
and any
combination of
the following:
P0301 (71)
P0302 (72)
P0303 (73)
P0304 (74) Random Misfire Detected
ON (see page 11-115)
P0301 (71) No. 1 Cylinder Misfire Detected ON (see page 11-118)
P0302 (72) No. 2 Cylinder Misfire Detected ON (see page 11-118)
P0303 (73) No. 3 Cylinder Misfire Detected ON (see page 11-118)
P0304 (74) No. 4 Cylinder Misfire Detected ON (see page 11-118)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
4: K20Z2 engine
5: K20Z3 engine
(cont’d)
4
5 4
5
08/08/21 14:12:35 61SNR030_110_0009
ProCarManuals.com
DYNOMITE -2009-

•••
•••
•••
•••Ó
•••
•••
•••
••• Ó
Ó
Ó
•••
••• Ó
•••
••• Ó
Ó
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
••• Ó
•••
•••
••• Ó
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-11
P0606 (0)
Engine Control Module (ECM)/Powertrain Control Module (PCM)
Processor Malfunction ON (see page 11-145)
P060A (131) Powertrain Control Module (PCM) (A/T System) Internal Control
Module Malfunction ON (see page 11-145)
P062F (131) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Internal Control Module Keep Alive Memory (KAM) Error ON (see page 11-144)
P0630 (139) VIN Not Programmed or Mismatch ON (see page 11-146)
P0685 (135) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Power Control Circuit/Internal Circuit Malfunction ON (see page 11-147)
P0720 (122) Output Shaft (Countershaft) Speed Sensor Circuit Malfunction ON (see page 11-148)
P0720 (122) Output Shaft (Countershaft) Speed Sensor Circuit Malfunction ON (see page 11-149)
P1009 (56) Variable Valve Timing Control (VTC) Advance Malfunction ON (see page 11-283)
P1109 (13) Barometric Pressure (BARO) Sensor Circuit Out of Range High ON (see page 11-152)
P1116 (86) Engine Coolant Temperature (ECT) Sensor 1 Circuit Range/
Performance Problem ON (see page 11-153)
P1128 (5) Manifold Absolute Pressure (MAP) Sensor Signal Lower Than
Expected ON (see page 11-155)
P1129 (5) Manifold Absolute Pressure (MAP) Sensor Signal Higher Than
Expected ON (see page 11-156)
P1157 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) AFS Circuit High Voltage ON (see page 11-157)
P1172 (61) Air Fuel Ratio (A/F) Sensor (Sensor 1) Circuit Out of Range High ON (see page 11-159)
P1297 (20) Electrical Load Detector (ELD) Circuit Low Voltage OFF (see page 11-160)
P1298 (20) Electrical Load Detector (ELD) Circuit High Voltage OFF (see page 11-162)
P1454 (91) Fuel Tank Pressure (FTP) Sensor Circuit Range/Performance Problem ON (see page 11-402)
P145C (90) Evaporative Emission (EVAP) System Purge Flow Malfunction ON (see page 11-404)
P1549 (34) Charging System High Voltage OFF (see page 11-164)
P1658 (40) Electronic Throttle Control System (ETCS) Control Relay ON
Malfunction ON (see page 11-241)
P1659 (40) Electronic Throttle Control System (ETCS) Control Relay OFF
Malfunction ON (see page 11-243)
P1683 (40) Throttle Valve Default Position Spring Performance Problem ON (see page 11-247)
P1684 (40) Throttle Valve Return Spring Performance Problem ON (see page 11-248)
P16BB (116) Alternator B Terminal Circuit Low Voltage OFF (see page 11-165)
P16BC (116) Alternator FR Terminal Circuit/IGP Circuit Low Voltage OFF (see page 11-166)
P2101 (40) Electronic Throttle Control System (ETCS) Malfunction ON (see page 11-249)
P2118 (40) Throttle Actuator Current Range/Performance Problem ON (see page 11-251)
P2122 (37) Accelerator Pedal Position (APP) Sensor A (Throttle Position (TP)
Sensor D) Circuit Low Voltage ON (see page 11-253)
P2123 (37) Accelerator Pedal Position (APP) Sensor A (Throttle Position (TP)
Sensor D) Circuit High Voltage ON (see page 11-256)
P2127 (37) Accelerator Pedal Position (APP) Sensor B (Throttle Position (TP)
Sensor E) Circuit Low Voltage ON (see page 11-257)
P2128 (37) Accelerator Pedal Position (APP) Sensor B (Throttle Position (TP)
Sensor E) Circuit High Voltage ON (see page 11-260)
P2135 (7) Throttle Position (TP) Sensor A/B Incorrect Voltage Correlation ON (see page 11-262)
P2138 (37) Accelerator Pedal Position (APP) Sensor A/B (Throttle Position (TP)
Sensor D/E) Incorrect Voltage Correlation ON (see page 11-264)
P2176 (40) Throttle Actuator Control System Idle Position Not Learned ON (see page 11-266)
P2183 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit Range/
Performance Problem ON (see page 11-168)
P2184 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit Low Voltage ON (see page 11-170)
P2185 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit High Voltage ON (see page 11-172)
P2195 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) Signal Stuck Lean ON (see page 11-174)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
1: A/T
2: The D indicator and the MIL may come on at the same time (A/T).
3: M/T
4: K20Z2 engine
5: K20Z3 engine
9: ’09 model
(cont’d)
1
9
1, 2
3
4
5
5
3
1
08/08/21 14:12:36 61SNR030_110_0011
ProCarManuals.com
DYNOMITE -2009-

Î
Vacuum Distribution
K20Z2 engine
11-23
3ENGINE
COOLANT
9
5 18
4
6
7
8 20
19 2 26
16
15
25
11 13
14
10 21
23
12 ATMOSPHERE
1
ENGINE
COOLANT
24
17ATMOSPHERE
22
MASS AIR FLOW (MAF) SENSOR/
INTAKE AIR TEMPERATURE (IAT) SENSOR
AIR FUEL RATIO (A/F) SENSOR (SENSOR 1)
SECONDARY HEATED OXYGEN SENSOR
(SECONDARY HO2S) (SENSOR 2)
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR
ENGINE COOLANT TEMPERATURE (ECT) SENSOR 1
CRANKSHAFT POSITION (CKP) SENSOR
KNOCK SENSOR
CAMSHAFT POSITION (CMP) SENSOR B
CAMSHAFT POSITION (CMP) SENSOR A
THROTTLE BODY
INJECTOR
FUEL PRESSURE REGULATOR
FUEL FILTER
FUEL PUMP
FUEL TANK INTAKE AIR RESONATOR
POSITIVE CRANKCASE VENTILATION (PCV) VALVE
THREE WAY CATALYTIC CONVERTER
EVAPORATIVE EMISSION (EVAP) CANISTER EVAPORATIVE EMISSION (EVAP) CANISTER
PURGE VALVE
EVAPORATIVE EMISSION (EVAP) CANISTER
VENT SHUT VALVE
FUEL TANK PRESSURE (FTP) SENSOR
INTAKE AIR BYPASS CONTROL THERMAL VALVE
FUEL TANK VAPOR CONTROL VALVE
AIR CLEANER EXHAUST GAS RECIRCULATION (EGR) VALVE and
POSITION SENSOR
(cont’d)
08/08/21 14:12:41 61SNR030_110_0023
ProCarManuals.com
DYNOMITE -2009-

Î
Vacuum Distribution (cont’d)
K20Z3 engine
11-24Fuel and Emissions Systems
System Description (cont’d)
3
ENGINE
COOLANT
9
5 17
4
6
7
8 19
18 2 25
16
15
24
11 13
14
10 20
22
12 ATMOSPHERE
1
ENGINE
COOLANT
23 ATMOSPHERE
21
MASS AIR FLOW (MAF) SENSOR/
INTAKE AIR TEMPERATURE (IAT) SENSOR
AIR FUEL RATIO (A/F) SENSOR (SENSOR 1)
SECONDARY HEATED OXYGEN SENSOR
(SECONDARY HO2S) (SENSOR 2)
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR
ENGINE COOLANT TEMPERATURE (ECT) SENSOR 1
CRANKSHAFT POSITION (CKP) SENSOR
KNOCK SENSOR
CAMSHAFT POSITION (CMP) SENSOR B
CAMSHAFT POSITION (CMP) SENSOR A
THROTTLE BODY
INJECTOR
FUEL PRESSURE REGULATOR
FUEL FILTER
FUEL PUMP
FUEL TANK INTAKE AIR RESONATOR
POSITIVE CRANKCASE VENTILATION (PCV) VALVE
THREE WAY CATALYTIC CONVERTER
EVAPORATIVE EMISSION (EVAP) CANISTER EVAPORATIVE EMISSION (EVAP) CANISTER
PURGE VALVE
EVAPORATIVE EMISSION (EVAP) CANISTER
VENT SHUT VALVE
FUEL TANK PRESSURE (FTP) SENSOR
INTAKE AIR BYPASS CONTROL THERMAL VALVE
FUEL TANK VAPOR CONTROL VALVE AIR CLEANER
08/08/21 14:12:42 61SNR030_110_0024
ProCarManuals.com
DYNOMITE -2009-

µ
Ø
ECM/PCM Inputs and Outputs at Connector A ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-26Fuel and Emissions Systems
System Description (cont’d)
NOTE: Standard battery voltage is about 12 V.
24 GRY VCC5 (SENSOR VOLTAGE) Provides sensor reference voltageWith ignition switch ON (II): about 5.0 V
25 BRN VCC4 (SENSOR VOLTAGE) Provides sensor reference voltageWith ignition switch ON (II): about 5.0 V
26 LT GRN FTP (FUEL TANK PRESSURE (FTP) SENSOR) Detects FTP sensor signal With ignition switch ON (II) and fuel fill cap
removed: about 2.5 V
27 PNK SLS (SHIFT LOCK SOLENOID) Drives shift lock solenoid With ignition switch ON (II), in P, brake pedal
pressed, and accelerator released:
battery voltage
27 GRN RVS (REVERSE LOCKOUT SOLENOID) Drives reverse lockout
solenoidWith vehicle speed below 9 mph (15 km/h):
battery voltage
With vehicle speed above 13 mph (20 km/h):
about 0 V
28 BLU NEP (ENGINE SPEED PULSE) Outputs engine speed pulse With engine running: pulses
29 BLU VSSOUT (VEHICLE SPEED SIGNAL OUTPUT) Sends vehicle speed signal Depending on vehicle speed: pulses
31 BRN SCS (SERVICE CHECK SIGNAL) Detects service check signal With service check signal shorted using HDS:
about 0 V
With service check signal opened: about 5.0 V
33 GRN ECT2 (ENGINE COOLANT TEMPERATURE (ECT)
SENSOR 2) Detects ECT sensor 2 signal With ignition switch ON (II): about 0.1 4.8 V
(depending on engine coolant temperature)
34 LT BLU SG5 (SENSOR GROUND) Sensor ground Less than 1.0 V at all times
35 BLU SG4 (SENSOR GROUND) Sensor ground Less than 1.0 V at all times
36 WHT CANH (CAN COMMUNICATION SIGNAL
HIGH) Sends communication
signal
With ignition switch ON (II): about 2.5 V (pulses)
37 RED CANL (CAN COMMUNICATION SIGNAL
LOW) Sends communication
signal
With ignition switch ON (II): about 2.5 V (pulses)
1: A/T
3: K20Z3 engine
1
3
Terminal side of female terminals
08/08/21 14:12:43 61SNR030_110_0026
ProCarManuals.com
DYNOMITE -2009-

ÎÚ
ECM/PCM Inputs and Outputs at Connector B ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-28Fuel and Emissions Systems
System Description (cont’d)
NOTE: Standard battery voltage is about 12 V.




1BLK/RED
(BLK) PG2 (POWER GROUND) Ground circuit for ECM/
PCMLess than 1.0 V at all times
2 BLU/RED EGR (EXHAUST GAS RECIRCULATION (EGR)
VALVE) Drives EGR valve With EGR operating: duty controlled
With EGR not operating: about 0 V
3 YEL/BLU PCS (EVAPORATIVE EMISSION (EVAP)
CANISTER PURGE VALVE) Drives EVAP canister purge
valve
With engine running, engine coolant below 60 °C
(140 °F): battery voltage
With engine running, engine coolant above 60 °C
(140 °F): duty controlled
4 BLK/WHT SO2SHTC (SECONDARY HEATED OXYGEN SENSOR
(SECONDARY HO2S)
HEATER (SENSOR 2)) Drives secondary HO2S
heater (sensor 2)
With ignition switch ON (II): battery voltage
With warmed up engine running: duty controlled
7 YEL/RED OPSW (OIL PRESSURE SWITCH) Detects engine oil pressure
signalWith ignition switch OFF: about 0 V
With engine running: battery voltage
8 BLU/RED OP2SW (2ND CLUTCH TRANSMISSION FLUID
PRESSURE SWITCH) Detects 2nd clutch
transmission fluid pressure
switch inputWith ignition switch ON (II):
Without 2nd clutch pressure: about 5.0 V
With 2nd clutch pressure: about 0 V
9 BLU/WHT OP3SW (3RD CLUTCH TRANSMISSION FLUID
PRESSURE SWITCH) Detects 3rd clutch
transmission fluid pressure
switch inputWith ignition switch ON (II):
Without 3rd clutch pressure: about 5.0 V
With 3rd clutch pressure: about 0 V
10 BLU/BLK SHA (SHIFT SOLENOID VALVE A) Drives shift solenoid
valve AWith engine running in R, D, and S (in 1st, 4th, or
5th gears): battery voltage
With engine running in P, N, D, and S (in 2nd and
3rd gears): about 0 V
11 GRN/WHT SHB (SHIFT SOLENOID VALVE B) Drives shift solenoid
valve BWith engine running in P, R, N, D, and S (in 1st and
2nd gears): battery voltage
With engine running in D and S (in 3rd, 4th, 5th
gears): about 0 V
12 RED/BLK ATPN (TRANSMISSION RANGE SWITCH N) Detects transmission range
switch N position signal
inputIn N: about 0 V
In any position other than N: about 5.0 V
13 BLU/BLK ATPP (TRANSMISSION RANGE SWITCH P) Detects transmission range
switch P position signal
inputIn P: about 0 V
In any position other than P: about 5.0 V
14 WHT ATPR (TRANSMISSION RANGE SWITCH R) Detects transmission range
switch R position signal
inputIn R: about 0 V
In any position other than R: about 5.0 V
15 RED ATPS (TRANSMISSION RANGE SWITCH S) Detects transmission range
switch S position signal
inputIn S: about 0 V
In any position other than S: battery voltage
1: A/T
4: K20Z2 engine
5: ’07-09 models
5
4
1
1
1
1
1
1
1
1
Terminal side of female terminals
08/08/21 14:12:43 61SNR030_110_0028
ProCarManuals.com
DYNOMITE -2009-

´´´
´
µ
µ
µ
ÎÚ
ECM/PCM Inputs and Outputs at Connector B ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-29
NOTE: Standard battery voltage is about 12 V.


16 BLU/YEL SUPP (PADDLE SHIFTER
(UPSHIFT SWITCH)) Detects paddle shifter
(upshift switch)In S:
With paddle shifter (upshift switch) pressed:
about 0 V
With paddle shifter (upshift switch) released:
battery voltage
17 WHT/RED NM (INPUT SHAFT (MAINSHAFT) SPEED
SENSOR) Detects input shaft
(mainshaft) speed sensor
signalWith ignition switch ON (II): about 0 V
With engine idling in N: about 2.5 V
18 YEL/BLU (YEL)VCC2 (SENSOR VOLTAGE) Provides sensor reference
voltageWith ignition switch ON (II): about 5.0 V
20 GRN SHC (SHIFT SOLENOID VALVE C) Drives shift solenoid
valve CWith engine running in N and S (in 1st, 3rd, and 5th
gears): battery voltage
With engine running in P, R, D, and S (in 2nd and
4th gears): about 0 V
21 YEL/GRN ATPD (TRANSMISSION RANGE SWITCH D) Detects transmission range
switch D position signal
inputIn D: about 0 V
In any position other than D: battery voltage
22 RED/WHT ATPRVS (TRANSMISSION RANGE SWITCH RVS) Detects transmission range
switch RVS position signal
inputIn R: about 0 V
In any position other than R: battery voltage
23 RED/WHT ECT1 (ENGINE COOLANT TEMPERATURE (ECT)
SENSOR 1) Detects ECT sensor 1 signal With ignition switch ON (II): about 0.1 4.8 V
(depending on engine coolant temperature)
24 YEL SHE (SHIFT SOLENOID VALVE E) Drives shift solenoid
valve EWith engine running in P and R: battery voltage
With engine running in N, D, and S (in 1st gear):
about 0 V
25 BLU/YEL LSC (A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE C) Drives A/T clutch pressure
control solenoid valve C
With ignition switch ON (II): current controlled
26 GRN/RED SHD (SHIFT SOLENOID VALVE D) Drives shift solenoid
valve DWith engine running in D and S (in 2nd and 5th
gears): battery voltage
With engine running in P, R, N, D, and S (in 1st, 3rd,
and 4th gears): about 0 V
27 RED/YEL TATF (ATF TEMPERATURE SENSOR) Detects ATF temperature
signalWith ignition switch ON (II): about 0.2 4.0 V
(about 1.8 V at operating temperature)
(depending on ATF temperature)
28 BLU/YEL ATPFWD (TRANSMISSION RANGE SWITCH FWD) Detects transmission range
switch D and S positions
signalIn D and S: about 0 V
In any other position D and S: battery voltage
29 WHT/BLK EGRP (EXHAUST GAS RECIRCULATION (EGR)
VALVE POSITION SENSOR) Detects EGR valve position
sensor signal
With engine running: about 1.2 3.0 V
(depending on EGR valve lift)
1: A/T
3: K20Z3 engine
4: K20Z2 engine
(cont’d)
1
1
3
1
1
1
1
1
1
1
1
4
Terminal side of female terminals
08/08/21 14:12:44 61SNR030_110_0029
ProCarManuals.com
DYNOMITE -2009-








PGM-FI System
Air Conditioning (A/C) Compressor Clutch Relay
Air Fuel Ratio (A/F) Sensor
Barometric Pressure (BARO) Sensor
Camshaft Position (CMP) Sensor BCrankshaft Position (CKP) Sensor
Engine Coolant Temperature (ECT) Sensor 1 and 2
Ignition Timing Control
Injector Timing and Duration
11-33
ZIRCONIA
ELEMENT
SENSOR
TERMINALS
HEATER
TERMINALS
O-RING
MAGNET
TERMINAL TERMINAL
O-RING
MAGNET
THERMISTOR O-RING TERMINAL
The programmed fuel injection (PGM-FI) system is a
sequential multiport fuel injection system.
When the ECM/PCM receives a demand for cooling
from the A/C system, it delays the compressor from
being energized, and enriches the mixture to assure
smooth transition to the A/C mode.
The A/F sensor operates over a wide air/fuel range. The
A/F sensor is installed upstream of the TWC, and sends
signals to the ECM/PCM which varies the duration of
fuel injection accordingly.
The BARO sensor is inside the ECM/PCM. It converts
atmospheric pressure into a voltage signal that
modifies the basic duration of the fuel injection
discharge.
CMP sensor B detects the position of the No. 1 cylinder
as a reference for sequential fuel injection to each
cylinder. The CKP sensor detects crankshaft speed and is used by
the ECM/PCM to determine the ignition timing, timing
for the fuel injection of each cylinder, and engine
misfire detection.
ECT sensors 1 and 2 are temperature dependent
resistors (thermistors). The resistance decreases as the
engine coolant temperature increases.
The ECM/PCM contains the memory for basic ignition
timing at various engine speeds and manifold absolute
pressures. It also adjusts the timing according to engine
coolant temperature and intake air temperature.
The ECM/PCM contains the memory for basic discharge
duration at various engine speeds and manifold
pressures. The basic discharge duration, after being
read out from the memory, is further modified by
signals sent from various sensors to obtain the final
discharge duration.
By monitoring long term fuel trim, the ECM/PCM
detects long term malfunctions in the fuel system and
sets diagnostic trouble codes (DTCs) if needed.
(cont’d)
08/08/21 14:13:37 61SNR030_110_0033
ProCarManuals.com
DYNOMITE -2009-