2006 ACURA CSX engine coolant



(#'

 )
10-1910-19
Radiator and Fan Replacement
B
A
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
AB
C
A
C
C C
5. Install the harness holder bracket (A), then install
the harness holder (B).
6. Install the air cleaner assembly (see page 11-345).
7. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
8. Clean up any spilled engine coolant. 1. Do the battery removal procedure (see page 22-69).
2. Drain the engine coolant (see page 10-8).
3. Remove the front grille cover (see page 20-163).
4. Disconnect the fan motor connectors (A) and the
hood switch connector (B), then remove the
harnessclamps(C).
(cont’d)
08/08/21 14:40:05 61SNR030_100_0019
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
10-1910-19
Radiator and Fan Replacement
B
A
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
AB
C
A
C
C C
5. Install the harness holder bracket (A), then install
the harness holder (B).
6. Install the air cleaner assembly (see page 11-345).
7. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
8. Clean up any spilled engine coolant. 1. Do the battery removal procedure (see page 22-69).
2. Drain the engine coolant (see page 10-8).
3. Remove the front grille cover (see page 20-163).
4. Disconnect the fan motor connectors (A) and the
hood switch connector (B), then remove the
harnessclamps(C).
(cont’d)
08/08/21 14:40:05 61SNR030_100_0019
ProCarManuals.com
DYNOMITE -2009-

Î Î
10-21
BA
C
A B
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft) C
9. Disconnect the engine coolant temperature (ECT)
sensor 2 connector (A), and remove the harness
clamp (B).
10. Disconnect the lower radiator hose (C) from the radiator.
11. A/T model: Disconnect the automatic transmission fluid (ATF) cooler hoses (A), then plug the lines and
the hoses. 12. Lower the vehicle on the lift.
13. Remove the condenser bracket mounting bolts (A)
and the bulkhead mounting bolts (B), then remove
the bulkhead (C).
(cont’d)
08/08/21 14:40:28 61SNR030_100_0021
ProCarManuals.com
DYNOMITE -2009-


10-22Cooling System
Radiator and Fan Replacement (cont’d)
RADIATOR FAN MOTOR
6x1.0mm
7 N·m
(0.7 kgf·m, 5 lbf·ft) RADIATOR FAN
UPPER RADIATOR HOSE
LOWER RADIATOR HOSE
O-RING
RADIATOR CAP
RADIATOR
O-RING LOWER CUSHION
DRAIN PLUG
6x1.0mm
7 N·m
(0.7 kgf·m, 5 lbf·ft)
A/C CONDENSER
FAN/SHROUD ASSEMBLY
RADIATOR FAN SHROUD
ENGINE COOLANT TEMPERATURE
(ECT) SENSOR 2
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
3.85 N·m
(0.393 kgf·m, 2.84 lbf·ft)
6.0 N·m
(0.61 kgf·m, 4.4 lbf·ft)
QUICK CONNECTOR
O-RING
14. Pull up the radiator, then remove the fan shroud assemblies and other parts from the radiator.
15. Install the radiator in the reverse order of removal. Make sure the upper and lower cushions are set securely.
16. Connect the lower radiator hose to the radiator.
17. Install the bulkhead in the reverse order of removal. Apply body paint to the bulkhead mounting bolts.
18. Do the battery installation procedure (see page 22-69).
19. Fill the radiator with engine coolant, and bleed the air from the cooling system with heater valve open (see step 6 on page 10-8).
20. Clean up any spilled engine coolant.
Replace. Replace.
Replace.
08/08/21 14:40:29 61SNR030_100_0022
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
10-23
Fan Controls
Component Location Index
FAN CONTROL RELAY
UNDER-HOOD FUSE/RELAY BOX
RADIATOR FAN RELAY
A/C CONDENSER FAN ASSEMBLY RADIATOR FAN ASSEMBLY ENGINE COOLANT TEMPERATURE
(ECT) SENSOR 2ENGINE COOLANT TEMPERATURE
(ECT) SENSOR 1
A/C CONDENSER FAN RELAY
Test, page 22-70
Test, page 22-70
Motor Test, page 10-5
Replacement, page 10-19 Motor Test, page 10-5
Replacement, page 10-19 Replacement, page 11-225Replacement, page 11-225
Test, page 22-70
08/08/21 14:40:31 61SNR030_100_0023
ProCarManuals.com
DYNOMITE -2009-

(#'

)
Symptom Diagnostic Procedure Also check for
10-24
Fan Controls
Symptom Troubleshooting Index
Engine overheats
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12. Check the coolant level.
Check for engine coolant leakage (from gaskets,
hoses, O-rings, etc.).
Check for dirt, leaves, or insects on radiator
and A/C condenser.
Check for deteriorated coolant.
Check for a damaged or deformed fan shroud.
Inspect the fan motors (see page 10-5) or fan
relays (see page 22-70).
Check the radiator cap (see page 10-4).
Check the thermostat (see page 10-5).
Inspect the water pump (see page 10-6).
Check for a clogged or deteriorated radiator
hoses.
Check for clogged heater core or hoses.
Check for a damaged cylinder head gasket.
The radiator fan does not run at
high speed Radiator fan high speed circuit troubleshooting
(see page 10-26). Cleanliness and
tightness of all
connectors
Both the radiator fan and the A/C
condenser fan do not run at low
speed Radiator and A/C condenser fans low speed circuit
troubleshooting (see page 21-56).
Cleanliness and
tightness of all
connectors
The A/C condenser fan does not
runathighspeed A/C condenser fan high speed circuit troubleshooting
(see page 21-60). Cleanliness and
tightness of all
connectors
08/08/21 14:40:31 61SNR030_100_0024
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
10-25
Circuit Diagram
ECT2
SG6
SG2
ECT1 FANH
FANL
SUBRLY IG2HOTinON(II)
PNK
5V No. 15 (7.5 A)
A21
PUR
ECM/PCM
2G301
BLK
2
1
No. 11 (15 A)
(10 A) No. 36
B23
RED/WHT GRN/BLK B33
BLU GRY
BRN
A33
BLK GRN A9 IGNITION SWITCH
IG2
BAT
RED
3
2 5
4 1
A4
A5 13
4
2
1 2 23 4
1 No. 2 (50 A)
BLK
UNDER-HOOD FUSE/RELAY BOX
BATTERY
G301No. 1 (100 A)
No. 6 (20 A)
A/C
CONDENSER
FAN RELAY
ENGINE COOLANT
TEMPERATURE
(ECT) SENSOR 1
A/C
CONDENSER
FAN MOTOR
FAN
CONTROL
RELAY
RADIATOR
FAN
MOTOR
ENGINE COOLANT
TEMPERATURE
(ECT) SENSOR 2 RADIATOR
FAN
RELAY
PGM-FI
SUB RELAY
H1
3 4
ORN
G12
D1
F16
F7
F2
F12
F14
F1
F11 No. 7 (20 A)
21
1 UNDER-DASH
FUSE/RELAY
BOX
BRN
WHT
43
12 C3
08/08/21 14:40:32 61SNR030_100_0025
ProCarManuals.com
DYNOMITE -2009-

•••Ó
Ó
•••
•••
•••
••• Ó
•••
••• Ó
•••
•••
•••
••• Ó
Ó
Ó
Ó
•••
••• Ó
••• ÓÓ
••• Ó
Ó
•••
••• Ó
Ó
Ó
Ó
Ó
(#')
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-9
DTC Troubleshooting Index
P0010 (56)
Variable Valve Timing Control (VTC) Oil Control Solenoid Valve
Malfunction ON (see page 11-274)
P0011 (56) Variable Valve Timing Control (VTC) System Malfunction ON (see page 11-276)
P0101 (50) Mass Air Flow (MAF) Sensor Circuit Range/Performance Problem ON (see page 11-74)
P0102 (50) Mass Air Flow (MAF) Sensor Circuit Low Voltage ON (see page 11-75)
P0103 (50) Mass Air Flow (MAF) Sensor Circuit High Voltage ON (see page 11-78)
P0107 (3) Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage ON (see page 11-80)
P0108 (3) Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage ON (see page 11-82)
P0111 (10) Intake Air Temperature (IAT) Sensor Circuit Range/Performance
Problem ON (see page 11-85)
P0112 (10) Intake Air Temperature (IAT) Sensor Circuit Low Voltage ON (see page 11-86)
P0113 (10) Intake Air Temperature (IAT) Sensor Circuit High Voltage ON (see page 11-87)
P0116 (86) Engine Coolant Temperature (ECT) Sensor 1 Circuit Range/
Performance Problem ON (see page 11-90)
P0117 (6) Engine Coolant Temperature (ECT) Sensor 1 Circuit Low Voltage ON (see page 11-91)
P0118 (6) Engine Coolant Temperature (ECT) Sensor 1 Circuit High Voltage ON (see page 11-92)
P0122 (7) Throttle Position (TP) Sensor A Circuit Low Voltage ON (see page 11-232)
P0123 (7) Throttle Position (TP) Sensor A Circuit High Voltage ON (see page 11-234)
P0125 (86) Engine Coolant Temperature (ECT) Sensor 1 Malfunction/Slow
Responce ON (see page 11-95)
P0128 (87) Cooling System Malfunction ON (see page 11-96)
P0133 (61) Air Fuel Ratio (A/F) Sensor (Sensor 1) Malfunction/Slow Response ON (see page 11-97)
P0134 (41) Air Fuel Ratio (A/F) Sensor (Sensor 1) Heater System Malfunction ON (see page 11-98)
P0135 (41) Air Fuel Ratio (A/F) Sensor (Sensor 1) Heater Circuit Malfunction ON (see page 11-99)
P0137 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit Low Voltage ON (see page 11-104)
P0138 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit High Voltage ON (see page 11-106)
P0139 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Slow Response ON (see page 11-109)
P0141 (65) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Heater Circuit Malfunction ON (see page 11-110)
P0171 (45) Fuel System Too Lean ON (see page 11-113)
P0172 (45) Fuel System Too Rich ON (see page 11-113)
P0222 (7) Throttle Position (TP) Sensor B Circuit Low Voltage ON (see page 11-236)
P0223 (7) Throttle Position (TP) Sensor B Circuit High Voltage ON (see page 11-239)
P0300 (75)
and any
combination of
the following:
P0301 (71)
P0302 (72)
P0303 (73)
P0304 (74) Random Misfire Detected
ON (see page 11-115)
P0301 (71) No. 1 Cylinder Misfire Detected ON (see page 11-118)
P0302 (72) No. 2 Cylinder Misfire Detected ON (see page 11-118)
P0303 (73) No. 3 Cylinder Misfire Detected ON (see page 11-118)
P0304 (74) No. 4 Cylinder Misfire Detected ON (see page 11-118)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
4: K20Z2 engine
5: K20Z3 engine
(cont’d)
4
5 4
5
08/08/21 14:12:35 61SNR030_110_0009
ProCarManuals.com
DYNOMITE -2009-