2006 ACURA CSX battery

(#'# 
#
)µµ(#'# 
#
)
µ
µ µ
µ
DTC 1303: DTC 1305:
YES
NO YES
NO
23-32423-324Navigation System
DTC Troubleshooting (cont’d)
GPS Receiver Error 2
Gyro Error 2: ECU Temp XX °C
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside and away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside and away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
 Do this test only when the dash temperature is between 20 °C ( 4 °F) and 70 °C (158 °F).
1. Clear hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.
Is DTC 1303 indicated?
Is DTC 1304 indicated?
08/08/21 14:16:46 61SNR030_230_0327
ProCarManuals.com
DYNOMITE -2009-

¦§ ¦§
(#'# 
#
)(#'# 
#
)
µ
µ
µ
µ µ
µ
µ
µ
DTC 1306: DTC 1307:
YES
NO
YES
NO YES
NO
YES
NO
23-32523-325
Vehicle Speed Pulse
DVD Read Error
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then start the engine.
3. Check for the hard error code (see page 23-273).
Go to step 4.
Intermittent failure, the system is OK at this
time.
4. Drive the vehicle and watch the VSP signal.
Replace the navigation unit (see page 23-355).
Do the symptom troubleshooting for vehicle
position icon constantly leaves road, moves
erratically or is very far from actual position
(see page 23-344). NOTE:
 Check the vehicle battery condition first.
 Check any official Honda service website for more information about the navigation system.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Inspect the navigation DVD for scratches or damage.
1. Turn the ignition switch to ON (II).
Go to DVD screen error messages (see page
23-319).
Go to step 2.
2. Clear the heard error code (see page 23-274).
3. Turn the ignition switch to LOCK (0), then back to ON (II).
4. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.
Is DTC 1306 indicated?
Does t he V SP si gnal change f r om 0 t o 1as you drive? Is there a DVD error message?
Is DTC 1307 indicated?
08/08/21 14:16:46 61SNR030_230_0328
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)(#'# 
#
)
µ
µ µ
µ
DTC 1402: DTC 1409:
YES
NO YES
NO
23-32623-326Navigation System
DTC Troubleshooting (cont’d)
Audio Error 2
Audio Error 9
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Check if the audio unit functions are working
properly. If any problems are found, go to the
applicable troubleshooting in audio section.
Intermittent failure, the system is OK at this
time. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Check the XM error codes (see page 23-194).
If any codes are detected, go to the applicable
troubleshooting in audio (XM) section.
Intermittent failure, the system is OK at this
time.
I s DT C 1402 i nd i cat ed ? I s DT C 1409 i nd i cat ed ?
08/08/21 14:16:46 61SNR030_230_0329
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)(#'# 
#
)
µ
µ µ
µ
µ
µ
DTC 2610: DTC 2701:
YES
NO
YES
NO
YES
NO
23-33023-330Navigation System
DTC Troubleshooting (cont’d)
DRAM Diag
GPS Diag: Antenna
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links, then select the ECU Info.
Intermittent failure, the system is OK at this
time.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside, away from buildings.
 Check for electronic aftermarket accessories (possibly hidden) mounted near the GPS antenna or
the navigation unit.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links, then select the GPS Ant.
Intermittent failure, the system is OK at this
time.
Go to step 5.
5. Turn the ignition switch to LOCK (0).
6. Check for poor connections at navigation unit connector H (2P).
Replace the GPS antenna (see page 23-358).
Repair the poor connection.
I s D-RAM OK i nd i cat ed ?
Is Antenna OK indicated?
I s t he connect i on OK ?
08/08/21 14:17:48 61SNR030_230_0333
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#)(#'# 
#)
µ
µ µ
µ
DTC 2702: DTC 2703:
YES
NO
YES
NO
23-33123-331
GPS Diag: Receiver in Navi ECUAircon Diag
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside, away from buildings.
 Check for electronic aftermarket accessories (possibly hidden) mounted near the GPS antenna or
the navigation unit.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Select the System Links, then select the GPS Ant.
Intermittent failure, the system is OK at this
time.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Check for B-CAN DTCs and resolve them before troubleshooting.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 DTC 2703 can be stored when the ignition switch is at ACCESSORY (I). With the ignition switch is in
ACCESSORY (I), the climate control unit is turned off
and the navigation unit loses communication and
stores DTCs. Therefore, there is a possibility that the
system is normal even DTC 2703 is stored. Check
system links (see page 23-297) with the engine
running, and if it shows normal, the system is OK at
this time. If not, do this troubleshooting.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and Select the Self- Diagnosis Mode in the Select Diagnosis Items
Menu (see page 23-297).
4. Check the System Links.
Go to step 5.
Intermittent failure, the system is OK at this
time.
5. Turn the ignition switch to LOCK (0).
(cont’d)
Is Receiver in Navi ECU OK indicated? Is the Air con icon r ed?
08/08/21 14:17:48 61SNR030_230_0334
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'#
)
´
µ
µ
µ
µ µ
µ
µ
µ
No picture is displayed
YES
NO
YES
NO YES
NO
YES
NO
23-338Navigation System
Symptom Troubleshooting
NAVIGATION UNIT CONNECTOR A (24P)
BBACKUP(WHT)
NAVIGATION UNIT CONNECTOR A (24P) ACC RADIO (PUR)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft code.
1. Check the No. 23 (10 A) fuse in the under-hood fuse/relay box and the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box, and reinstall the fuse if
it is OK.
Go to step 2.
Replace the fuse and recheck.
2. Turn the ignition switch to ON (II).
3. Operate the radio and listen to the audio.
Go to step 4.
Refer to audio system troubleshooting.
4. Turn the ignition switch to LOCK (0).
5. Remove the navigation unit (see page 23-355). 6. Measure the voltage between navigation unit
connector A (24P) terminal No. 24 and body ground.
Go to step 7.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
7. Turn the ignition switch to ON (II).
8. Measure the voltage between navigation unit connector A (24P) terminal No. 14 and body ground.
Go to step 9.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
Wire side of female terminals
Wire side of female terminals
IsthefuseOK? Can y ou hear t he aud i o? Is there battery voltage?
Is there battery voltage?
08/08/21 14:17:50 61SNR030_230_0341
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'#
)

µ
µ µ
µ
µ
µ
µ
µ
YES
NO Diagnostic Test: Monitor Check
YES
NO
YES
NO
YES
NO
Picture has lines/rolls/other issues or is an
odd color
23-33923-339
NAVIGATION UNIT CONNECTOR A (24P) RADIO GND (BLK)
NAVIGATION UNIT CONNECTOR C (8P) GND (BLK)
9. Measure the voltage between navigation unitconnector A (24P) terminal No. 12 and body ground,
and between navigation unit connector C (8P)
terminal No. 4 and body ground.
Replace the navigation unit (see page 23-355).
Repair open in the wire between the
navigation unit and body ground (G 504) (see page
22-30), (G505) (see page 22-32). NOTE:
 Check the vehicle battery condition frist.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the navigation screen settings for brightness, contrast, black level and the color screen for map
color and menu color.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft codes.
1. Check for electronic aftermarket accessories (possibly hidden) mounted near the navigation unit.
Disable the accessories, and recheck.
Go to step 2.
2. Turn the ignition switch to ON (II).
3. Start up the navigation picture.
Go to step 5.
Go to step 4.
4. Go into the Detail Information & Settings, select Monitor Check, and use RGB Color diagnostic
under Monitor Check (see page 23-302).
Go to step 5.
Replace the navigation unit (see page 23-355).
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is t her e l ess t han 0.1 V ? Ar e t her e any el ect r oni c accessor i es?
Is the picture scrolling horizontally (lef t to right orright to left)?
Ar e t he r ed , gr een, and bl ue col or ed ci r cl esshow n?
08/08/21 14:17:50 61SNR030_230_0342
ProCarManuals.com
DYNOMITE -2009-

(#'#
)

µ
µ
µ
µ
YES
NO
YES
NO
Navigation display buttons do not work or
respond properly
23-34023-340Navigation System
Symptom Troubleshooting (cont’d)
5. Turn the ignition switch to LOCK (0), then turn to
ON (II), and observe the navigation picture.
Check for sources of electrical noise, such as
poor battery connection, alternator, defective
battery, aftermarket accessories or cell phone, and
poor pin fits at the navigation unit.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Always make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Always check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft codes.
1. Turn the ignition switch to ON (II).
2. Go into the Detail Information & Settings select Unit Check, and use Hard Key test under Unit Check
(see page 23-305).
The system is OK at this time.
Replace the navigation unit (see page 23-355).
Di d t he i mage i mpr ov e?
Does t he nav i gat i on uni t but t ons w or k pr oper l y ?
08/08/21 14:17:50 61SNR030_230_0343
ProCarManuals.com
DYNOMITE -2009-