2006 ACURA CSX reset


(#' 


)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0117:
YES
NO
YES
NO YES
NO
YES
NO
11-91
ECT SENSOR 1 2P CONNECTOR
ECT1
(RED/WHT)
ECT Sensor 1 Circuit Low Voltage
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3). 1. Turn the ignition switch to ON (II).
2. Check ECT SENSOR 1 in the DATA LIST with the HDS.
Go to step 3.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at ECT sensor 1 and the ECM/PCM.
3. Turn the ignition switch to LOCK (0).
4. Disconnect ECT sensor 1 2P connector.
5. Turn the ignition switch to ON (II).
6. Check ECT SENSOR 1 in the DATA LIST with the HDS.
Go to step 7.
Go to step 11.
7. Turn the ignition switch to LOCK (0).
8. Jump the SCS line with the HDS.
9. Disconnect ECM/PCM connector B (44P). 10. Check for continuity between ECT sensor 1 2P
connector terminal No. 1 and body ground.
Repair short in the wire between ECT
sensor 1 and the ECM/PCM (B23), then go to step
13.
Go to step 18.
11. Turn the ignition switch to LOCK (0).
12. Replace ECT sensor 1 (see page 11-225).
13. Reconnect all connectors.
14. Turn the ignition switch to ON (II).
15. Reset the ECM/PCM with the HDS.
16. Do the ECM/PCM idle learn procedure (see page 11-310).
17. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at ECT sensor 1 and the ECM/PCM, then
go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
(cont’d)
Wire side of female terminals
I s about 180 ° C ( 35 6 ° F ) or mor e, or 0.08 V or l essindicated?
I s about 180 ° C ( 35 6 ° F ) or mor e, or 0.08 V or l essindicated? Is there continuity?
Is DTC P0117 indicated?
08/08/21 14:17:16 61SNR030_110_0091
ProCarManuals.com
DYNOMITE -2009-

µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-94PGM-FI System
DTC Troubleshooting (cont’d)
ECT SENSOR 1 2P CONNECTOR
ECM/PCM CONNECTOR B (44P)
ECT1 (RED/WHT)
ECT1 (RED/WHT)
16. Turn the ignition switch to LOCK (0).
17. Jump the SCS line with the HDS.
18. Disconnect ECM/PCM connector B (44P).
19. Check for continuity between ECT sensor 1 2Pconnector terminal No. 1 and ECM/PCM connector
terminal B23.
Go to step 27.
Repair open in the wire between the ECM/
PCM (B23) and ECT sensor 1, then go to step 22. 20. Turn the ignition switch to LOCK (0).
21. Replace ECT sensor 1 (see page 11-225).
22. Reconnect all connectors.
23. Turn the ignition switch to ON (II).
24. Reset the ECM/PCM with the HDS.
25. Do the ECM/PCM idle learn procedure (see page
11-310).
26. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at ECT sensor 1 and the ECM/PCM, then
go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
27. Reconnect all connectors.
28. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
29. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at ECT sensor 1 and the ECM/PCM. If the
ECM/PCM was updated, substitute a known-good
ECM/PCM (see page 11-7), then recheck. If the
ECM/PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Wire side of female terminals
Terminal side of female terminals
Is there continuity? Is DTC P0118 indicated?
Is DTC P0118 indicated?
08/08/21 14:17:17 61SNR030_110_0094
ProCarManuals.com
DYNOMITE -2009-

µµ
µ
(#' 

)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P0128:
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
11-96PGM-FI System
DTC Troubleshooting (cont’d)
Cooling System Malfunction
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Make sure the blower switch is OFF.
4. Check the FAN CTRL in the DATA LIST with the HDS.
Go to step 5.
Wait until the FAN CTRL is off, then go to step
5.
5. Check the radiator fan operation.
Check the radiator fan high speed circuit
(see page 10-26), and the radiator fan relay
(see page 22-70). If the circuit and the relay are OK,
go to step 19.
Go to step 6.
6. Let the engine cool until the coolant temperature is 40 °C (104 °F) or less.
7. Note the value of ECT SENSOR 1 and ECT SENSOR 2intheDATALISTwiththeHDS.
8. Start the engine, and let it idle.
9. Let the engine idle until ECT SENSOR 1 goes up 22 °C (40 °F) or more from the recorded
temperature.
10. Check ECT SENSOR 2 in the DATA LIST with the HDS. 11. Compare the recorded value of ECT SENSOR 2 and
the present value of ECT SENSOR 2.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at ECT sensor 1, ECT sensor 2, and the ECM/PCM.
Test the thermostat (see page 10-5), then go
to step 12.
12. Turn the ignition switch to ON (II).
13. Reset the ECM/PCM with the HDS.
14. Let the engine cool until the coolant temperature is between 6 °C (21 °F) and 40 °C (104 °F).
15. Do the ECM/PCM idle learn procedure (see page 11-310).
16. Test-drive at a steady speed between 24 120 km/h (15 75 mph) for 10 minutes.
17. Check for Temporary DTCs or DTCs with the HDS.
Check the cooling system (see page 10-2),
then go to step 1.
Go to step 18.
18. Monitor the OBD STATUS for DTC P0128 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 17,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check the
coolingsystem(seepage10-2),thengotostep1.If
the screen indicates NOT COMPLETED, go to step
14.
Is it OFF?
Does t he r ad i at or f an k eep r unni ng? Di d t emper at ur e r i se 8 ° C ( 14 ° F ) or mor e f r om t he
r ecor d ed t emper at ur e?
Is DTC P0128 indicated?Does t he scr een i nd i cat e PASSE D?
08/08/21 14:17:17 61SNR030_110_0096
ProCarManuals.com
DYNOMITE -2009-

µµ
µ
µµ
(#' 

)
µ
µ µ
µ µ
µ
YES
NO
YES
NO
YES
NO
DTC P0133:
11-9711-97
19. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
20. Let the engine cool until the coolant temperature is between 6 °C (21 °F) and 40 °C (104 °F).
21. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
22. Test-drive at a steady speed between 24 120 km/h (15 75 mph) for 10 minutes.
23. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at ECT sensor 1, ECT sensor 2, and the
ECM/PCM. If the ECM/PCM was updated, substitute
a known-good ECM/PCM (see page 11-7), then go
to step 20. If the ECM/PCM was substituted, go to
step 1.
Go to step 24.
24. Monitor the OBD STATUS for DTC P0128 in the DTCs MENU with the HDS.
If the ECM/PCM was updated,
troubleshooting is complete. If the ECM/PCM was
substituted, replace the original ECM/PCM
(see page 11-228). If any other Temporary DTCs or
DTCs were indicated in step 23, go to the indicated
DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at ECT sensor 1,
ECT sensor 2, and the ECM/PCM. If the ECM/PCM
was updated, substitute a known-good ECM/PCM
(see page 11-7), then go to step 20. If the ECM/PCM
was substituted, go to step 1. If the screen indicates
NOT COMPLETED, go to step 20. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
4. Test-drive under these conditions:  Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
 A/TinD,M/Tin3rdor4th
 Drive the vehicle at 40 km/h (25 mph) or less for 5 minutes, then drive at a steady speed between
41 130 km/h (26 81 mph).
5. Monitor the OBD STATUS for DTC P0133 in the DTCs MENU with the HDS.
Go to step 6.
If the screen indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals at the A/F
sensor (Sensor 1) and the ECM/PCM. If the screen
indicates EXECUTING, keep driving until a result
comes on. If the screen indicates OUT OF
CONDITION, go to step 3 and recheck.
6. Turn the ignition switch to LOCK (0).
7. Replace the A/F sensor (Sensor 1) (see page 11-221).
8. Turn the ignition switch to ON (II).
9. Reset the ECM/PCM with the HDS.
(cont’d)A/F Sensor (Sensor 1)
Malfunction/Slow Response
Is DTC P0128 indicated?
Does t he scr een i nd i cat e PASSE D? Does t he scr een i nd i cat e F AILE D?
08/08/21 14:17:17 61SNR030_110_0097
ProCarManuals.com
DYNOMITE -2009-

µµ
(#' 

)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
DTC P0134:
11-9811-98PGM-FI System
DTC Troubleshooting (cont’d)
10. Do the ECM/PCM idle learn procedure (see page
11-310).
11. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
12. Test-drive under these conditions:
 Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
 A/TinD,M/Tin3rdor4th
 Drive the vehicle at 40 km/h (25 mph) or less for 5 minutes, then drive at a steady speed between
41 130 km/h (26 81 mph).
13. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/F sensor (Sensor 1) and the ECM/
PCM, then go to step 1.
Go to step 14.
14. Monitor the OBD STATUS for DTC P0133 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 13,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the A/F sensor
(Sensor1)andtheECM/PCM,thengotostep1.If
the screen indicates EXECUTING, keep driving until
a result comes on. If the screen indicates OUT OF
CONDITION, go to step 11. NOTE:
 Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
 If the vehicle was out of fuel and the engine stalled before this DTC was stored, refuel and clear the DTC
with the HDS.
 If DTC P0135 is stored at the same time as DTC P0134, troubleshoot DTC P0135 first, then recheck for DTC
P0134.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and let it idle without load (A/T in P or N, M/T in neutral) until the radiator fan comes
on.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the A/F sensor (Sensor 1), the PGM-FI subrelay,
and the ECM/PCM.
5. Turn the ignition switch to LOCK (0).
6. Replace the A/F sensor (Sensor 1) (see page 11-221).
7. Turn the ignition switch to ON (II).
8. Reset the ECM/PCM with the HDS.
9. Do the ECM/PCM idle learn procedure (see page 11-310).
10. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/F sensor (Sensor 1), the PGM-FI
subrelay, and the ECM/PCM, then go to step 1.
Go to step 11.A/F Sensor (Sensor 1) Heater
System Malfunction
Is DT C P0133 ind icated ?
Does t he scr een i nd i cat e PASSE D? Is DT C P0134 ind icated ?
Is DT C P0134 ind icated ?
08/08/21 14:17:18 61SNR030_110_0098
ProCarManuals.com
DYNOMITE -2009-

Î
´
µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-103
E
A/F SENSOR (SENSOR 1) 4P CONNECTOR B(PUR)
20. Remove the PGM-FI subrelay (E) from the under-hood fuse/relay box.
21. Disconnect the A/F sensor (Sensor 1) 4P connector.
22. Disconnect the EVAP canister vent shut valve 2P connector.
23. Check for continuity between A/F sensor (Sensor 1) 4P connector terminal No. 4 and body ground.
Repair short in the wire between the PGM-FI
subrelay, the EVAP canister vent shut valve, and
the A/F sensor (Sensor 1). Also replace the No. 11
FISUB(15A)fuse,thengotostep25.
Replace the under-hood fuse/relay box
(see page 22-65), then go to step 25. 24. Replace the A/F sensor (Sensor 1) (see page
11-221).
25. Reconnect all connectors.
26. Turn the ignition switch to ON (II).
27. Reset the ECM/PCM with the HDS.
28. Do the ECM/PCM idle learn procedure (see page 11-310).
29. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/F sensor (Sensor 1), the PGM-FI
subrelay, and the ECM/PCM, then go to step 1.
Go to step 30.
30. Monitor the OBD STATUS for DTC P0135 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 29,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the A/F sensor
(Sensor 1), the PGM-FI subrelay, and the ECM/PCM,
then go to step 1. If the screen indicates NOT
COMPLETED, keep idling until a result comes on.
(cont’d)
Terminal side of male terminals
Is there continuity? Is DT C P0135 ind icated ?
Does t he scr een i nd i cat e PASSE D?
08/08/21 14:17:21 61SNR030_110_0103
ProCarManuals.com
DYNOMITE -2009-

µ

µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-105
SECONDARY HO2S (SENSOR 2) 4P CONNECTOR
SHO2S (WHT)
13. Check for continuity between secondary HO2S(Sensor 2) 4P connector terminal No. 2 and body
ground.
Repair short in the wire between the ECM/
PCM (C27) and the secondary HO2S (Sensor 2),
then go to step 16.
Go to step 24.
14. Turn the ignition switch to LOCK (0).
15. Replace the secondary HO2S (Sensor 2) (see page 11-221).
16. Reconnect all connectors.
17. Turn the ignition switch to ON (II).
18. Reset the ECM/PCM with the HDS.
19. Do the ECM/PCM idle learn procedure (see page 11-310).
20. Start the engine, and let it idle without load (A/T in P or N, M/T in neutral) until the radiator fan comes
on. 21. Test-drive under these conditions:
 Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
 A/TinD,M/Tin4th
 Engine speed between 1,500 3,000 rpm
 Drive about 1 minute or more
22. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the secondary HO2S (Sensor 2) and
theECM/PCM,thengotostep1.
Go to step 23.
23. Monitor the OBD STATUS for DTC P0137 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 22,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the secondary
HO2S(Sensor2)andtheECM/PCM,thengotostep
1. If the screen indicates EXECUTING, keep driving
until a result comes on. If the screen indicates OUT
OF CONDITION, go to step 20.
(cont’d)
Terminal side of male terminals
Is there continuity? Is DT C P0137 ind icated ?
Does t he scr een i nd i cat e PASSE D?
08/08/21 14:17:21 61SNR030_110_0105
ProCarManuals.com
DYNOMITE -2009-


µ
µ
µ
µ µ
µ
YES
NO
YES
NO
YES
NO
11-107
SECONDARY HO2S (SENSOR 2) 4P CONNECTOR
SHO2S (WHT)JUMPER WIRE ECM/PCM CONNECTOR C (44P)
SHO2S (WHT/RED)
9. Turn the ignition switch to ON (II).
10. Check the HO2S S2 in the DATA LIST with the HDS.
Go to step 11.
Go to step 20.
11. Turn the ignition switch to LOCK (0).
12. Remove the jumper wire from the secondary HO2S (Sensor 2) 4P connector.
13. Connect secondary HO2S (Sensor 2) 4P connector terminal No. 2 to body ground with a jumper wire.
14. Turn the ignition switch to ON (II).
15. Check the HO2S S2 in the DATA LIST with the HDS. Go to step 16.
Repair open in the wire between the ECM/
PCM (A9) and the secondary HO2S (Sensor 2), then
go to step 22. 16. Turn the ignition switch to LOCK (0).
17. Jump the SCS line with the HDS.
18. Disconnect ECM/PCM connector C (44P).
19. Check for continuity between ECM/PCM connector
terminal C27 and body ground.
Go to step 30.
Repair open in the wire between the ECM/
PCM (C27) and the secondary HO2S (Sensor 2),
then go to step 22.
20. Turn the ignition switch to LOCK (0).
21. Replace the secondary HO2S (Sensor 2) (see page 11-221).
22. Reconnect all connectors.
23. Turn the ignition switch to ON (II).
24. Reset the ECM/PCM with the HDS.
25. Do the ECM/PCM idle learn procedure (see page 11-310).
(cont’d)
Terminal side of male terminals Terminal side of female terminals
Does t he v ol t age st ay at 1.27 V or mor e?
Does t he v ol t age st ay at 1.27 V or mor e? Is there continuity?
08/08/21 14:17:22 61SNR030_110_0107
ProCarManuals.com
DYNOMITE -2009-