2006 ACURA CSX glove box


(#' 
'
-)
µ
µ µ
µ
DTC 12-3x (‘‘x’’ can be 0 thru 9 or A thru F):
DTC 12-6x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO YES
NO
24-58SRS
DTC Troubleshooting (cont’d)
A
070AZ-SNAA100
07SAZ-TB4011A
Short to Another Wire or Decreased
Resistance in the Front Passenger’s Airbag
First Inflator
Short to Another Wire or Decreased
Resistance in the Front Passenger’s Airbag
Second Inflator
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead J 070AZ-SNAA100
 SRS short canceller 070AZ-SAA0100
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the lower glove box (see page 20-104),
then disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
5. Connect the SRS inflator simulator (2 connectors) and simulator lead J to dashboard wire
harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-22).
Go to step 9.
Short in the front passenger’s airbag first or
second inflator; replace the front passenger’s
airbag (see page 24-189), then clear the DTC.
9. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes.
10. Disconnect SRS unit connector A (28P) from the SRS unit (see step 9 on page 24-21).
11. Disconnect the SRS inflator simulator from the SRS simulator lead. Do not disconnect the simulator
lead from the dashboard wire harness 4P connector.
12. Connect the SRS short cancellers (070AZ-SAA0100) to the SRS unit connector A (28P) terminals No. 9
and No. 10 and No. 3 and terminals No. 3 and No. 4
(see page 24-18).
Does the SRS indicator stay on, and is DT C 12-3xor 12-6x i nd i cat ed ? I s DT C 12-3x or 12-6x i nd i cat ed ?
08/08/21 13:55:43 61SNR030_240_0058
ProCarManuals.com
DYNOMITE -2009-



µ
µ µ
µ
YES
NO YES
NO
24-60SRS
DTC Troubleshooting (cont’d)
A
070AZ-SNAA100
07SAZ-TB4011A DASHBOARD WIRE HARNESS
4P CONNECTOR
070AZ-SNAA100
3. Turn the ignition switch to LOCK (0). Disconnect thenegative cable from the battery, then wait at least 3
minutes.
4. Remove the lower glove box (see page 20-104), then disconnect the front passenger’s airbag 4P
connector (A) from dashboard wire harness.
5. Connect the SRS inflator simulator (2 connectors) and simulator lead J to the dashboard
wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-22).
Go to step 9.
Short to power in the front passenger’s airbag
first or second inflator; replace the front passenger’s
airbag (see page 24-189), then clear the DTC.
9. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes.
10. Disconnect SRS unit connector A (28P) from the SRS unit (see step 9 on page 24-21).
11. Disconnect the SRS inflator simulator from the SRS simulator lead. Do not disconnect the simulator
lead from the dashboard wire harness 4P connector. 12. Reconnect the negative cable to the battery.
13. Turn the ignition switch to ON (II).
14. Measure the voltage between each terminal of the
SRS simulator lead and body ground. There should
be less than 0.2 V.
Faulty SRS unit or poor connection at SRS
unit connector A (28P) and the SRS unit. Check the
connection between the connector and the SRS
unit. If the connection is OK, replace the SRS unit
(see page 24-203).
Short to power in the dashboard wire
harness; replace the dashboard wire harness, then
clear the DTC.
I s DT C 12-8x or 12-Ax i nd i cat ed ? Is the voltage as specif ied?
08/08/21 13:55:43 61SNR030_240_0060
ProCarManuals.com
DYNOMITE -2009-


(#' 
'
-)
µ
µ
µ
µ
DTC 12-9x (‘‘x’’ can be 0 thru 9 or A thru F):
DTC 12-Bx (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO YES
NO
24-61
A
070AZ-SNAA100
07SAZ-TB4011A
Short to Ground in the Front Passenger’s
Airbag First Inflator
Short to Ground in the Front Passenger’s
Airbag Second Inflator
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead J 070AZ-SNAA100
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC. 3. Turn the ignition switch to LOCK (0). Disconnect the
negative cable from the battery, then wait at least 3
minutes.
4. Remove the lower glove box (see page 20-104), then disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
5. Connect the SRS inflator simulator (2 connectors) and simulator lead J to the dashboard
wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-22).
Go to step 9.
Short to ground in the front passenger’s
airbag first or second inflator; replace the front
passenger’s airbag (see page 24-189), then clear
the DTC.
9. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes.
10. Disconnect SRS unit connector A (28P) from the SRS unit (see step 9 on page 24-21).
11. Disconnect the SRS inflator simulator from the SRS simulator lead. Do not disconnect the simulator
lead from the dashboard wire harness 4P connector.
(cont’d)
Does the SRS indicator stay on, and is DT C 12-9xor 12-Bx i nd i cat ed ?
I s DT C 12-9x or 12-Bx i nd i cat ed ?
08/08/21 13:56:54 61SNR030_240_0061
ProCarManuals.com
DYNOMITE -2009-




(#'
 )
Removal
24-189
Front Passenger’s Airbag Replacement
A A
B
CC
NOTE: If replacing the front passenger’s airbag after
deployment, refer to Component Replacement/
Inspection After Deployment (see page 24-185) for a
complete list of other parts that must also be replaced.1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the glove box (see page 20-104).
3. Disconnect the front passenger’s airbag 4P connector (A) from the dashboard wire harness.
4. Remove the center panel:  Navigation unit, with navigation system.– ’06-08 models (see page 23-256)
– ’09 model (see page 23-355)
 Audio unit, without navigation system. – ’06-08 models (see page 23-80)
– ’09 model (see page 23-155) 5. Remove the three mounting nuts (A) from the
bracket. Cover the front passenger’s lid and
dashboard with a cloth, and pry carefully with a
screwdriver to lift the front passenger’s airbag
assembly (B) out of the dashboard. If you replacing
only the front passenger’s lid, go to step 6.
NOTE: The front passenger’s lid has pawls (C) on
each side which attach it to the dashboard.
(cont’d)
08/08/21 14:01:55 61SNR030_240_0189
ProCarManuals.com
DYNOMITE -2009-




Installation
24-190SRS
Front Passenger’s Airbag Replacement (cont’d)
A
A
B
A
B B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
6. Cut the four parts (A) of the front passenger’s lid (B)as shown, and remove the front passenger’s airbag.
NOTE: Always replace the front passenger’s lid whenever you remove the front passenger’s
airbag from the lid.
 Replace the front passenger’s airbag if the airbag mounting hooks or its housing is damaged.
7. Insert the hooks (A) of the front passenger’s airbag housing into the new front passenger’s lid, then
insert the other hooks (B) into the lid.
NOTE: Make sure there are no objects between the airbag and the front passenger’s lid.
 Make sure the airbag is fully seated, and make sure the front passenger’s lid is not deformed or
damaged after the airbag is in place.
 Do not use tools when detaching the front passenger’s airbag in order to protect it. 1. Place the front passenger’s airbag assembly (A)
into the dashboard. Tighten the front passenger’s
airbag mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector (A) to dashboard wire harness, then reinstall the
glove box and center panel.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTC (see page 24-23).
5. After installing the airbag, confirm proper system operation: Turn the ignition switch to ON (II); the
SRS indicator should come on for about 6 seconds
andthengooff.
08/08/21 14:01:56 61SNR030_240_0190
ProCarManuals.com
DYNOMITE -2009-

Î


Î
(#'
!)
Special Tools Required
Driver’s Airbag
Front Passenger’s Airbag
Side Airbag
Side Curtain Airbag
Deploying Airbags in the Vehicle
24-196
SRS
Airbag and Tensioner Disposal
A
B
A
A
A
Deployment tool 07HAZ-SG00500
Before scrapping any airbags, side airbags, side curtain
airbags, seat belt tensioners, or seat belt buckle
tensioner (including those in a whole vehicle to be
scrapped), the part(s) must be deployed. If the vehicle is
still within the warranty period, the Honda District Parts
and Service Manager must give approval and/or special
instructions before deploying the part(s). Only after the
part(s) have been deployed (as the result of vehicle
collision, for example), can they be scrapped.
If the parts appear intact (not deployed), treat them with
extreme caution. Follow this procedure.
If an SRS equipped vehicle is to be entirely scrapped, its
airbags, side airbags, side curtain airbags, seat belt
tensioners, and seat belt buckle tensioner should be
deployed while still in the vehicle. These parts should
not be considered as salvageable parts and should
never be installed in another vehicle.1. Turn the ignition switch to LOCK (0), then disconnect the negative cable from the battery,
then wait at least 3 minutes before starting work.
2. Confirm that each airbag, side airbag, side curtain airbag, seat belt tensioner, or seat belt buckle
tensioner is securely mounted.
3. Confirm that the deployment tool is functioning properly by following the check procedure on the
tool label.
4. Remove the access panel (A) from the steering wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel. 5. Remove the glove box, then disconnect the front
passenger’s airbag 4P connector (A) from the
dashboard wire harness.
6. Disconnect the side airbag 2P connector (A) from the floor wire harness.
7. Disconnect the floor wire harness 2P connector from the side curtain airbag (A).
08/08/21 14:01:58 61SNR030_240_0196
ProCarManuals.com
DYNOMITE -2009-