2006 ACURA CSX fuel

Î
 
(#'
 )
6-386-38 Cylinder Head
Cylinder Head Cover Installation
(cont’d)
Cylinder Head Removal
B
C
A
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) A
B
8. Install two bolts (A) securing the evaporativeemission (EVAP) canister purge valve bracket.
9. Connect the breather hose (B), and install the dipstick (C).
10. Connect the evaporative emission (EVAP) canister purge valve connector.
11. Install the four ignition coils (see page 4-21).
12. Install the engine cover. NOTE:
 Use fender covers to avoid damaging the painted surfaces.
 To avoid damaging the wire and terminals, unplug the wiring connectors carefully while holding the
connector portion.
 Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3),
and monitor the engine coolant temperature (ECT)
sensor 1. To avoid damaging the cylinder head, wait
until the engine coolant temperature drops below
38 °C (100 °F) before loosening the cylinder head
bolts.
 Mark all wiring and hoses to avoid misconnection. Also, be sure that they do not contact other wiring or
hoses, or interfere with other parts.
1. Relieve the fuel pressure (see page 11-322).
2. Drain the engine coolant (see page 10-8).
3. Remove the air cleaner assembly (see page 11-345).
4. Remove the drive belt (see page 4-31).
5. Remove the intake manifold:  K20Z2 engine (see page 9-3)
 K20Z3 engine (see page 9-7)
6. Remove the exhaust manifold (see page 9-11).
7. Disconnect the evaporative emission (EVAP) canister hose (A) and the brake booster vacuum
hose (B).
08/08/21 14:27:27 61SNR030_060_0038
ProCarManuals.com
DYNOMITE -2009-




6-39
A
B
A B B
A
A B
8. Remove the quick-connect fitting cover (A), then
disconnect the fuel feed hose (B) (see page 11- 329).
9. Disconnect the positive crankcase ventilation (PCV) hose (A) (K20Z2 engine) and remove the ground
cable (B). 10. Remove the harness holder (A) from the bracket,
then remove the harness holder bracket (B).
11. Disconnect the upper radiator hose (A) and the heater hoses (B).
(cont’d)
08/08/21 14:27:27 61SNR030_060_0039
ProCarManuals.com
DYNOMITE -2009-


6-40Cylinder Head
Cylinder Head Removal (cont’d)
B
A
12. Remove the bolt (A) securing the connecting pipe.
13. Disconnect the water bypass hose (B).
14. Disconnect the following engine wire harnessconnectors, and remove the wire harness clamps
from the cylinder head.
 Four fuel injector connectors
 Engine coolant temperature (ECT) sensor 1 connector
 Camshaft position (CMP) sensor A (Intake) connector
 Camshaft position (CMP) sensor B (Exhaust) connector
 Rocker arm oil control valve connector
 Rocker arm oil pressure switch connector
 EVAP canister purge valve connector
 Variable valve timing control (VTC) oil control solenoid valve connector
 Exhaust gas recirculation (EGR) valve connector (K20Z2 engine)
 Engine oil pressure switch connector 15. Remove the cam chain (see page 6-18).
16. Remove the rocker arm assembly:
 K20Z2 engine (see page 6-43)
 K20Z3 engine (see page 6-44)
17. Remove the cylinder head bolts. To prevent warpage, loosen the bolts in sequence 1/3 turn at a
time. Repeat the sequence until all bolts are
loosened.
18. Remove the cylinder head.
08/08/21 14:27:28 61SNR030_060_0040
ProCarManuals.com
DYNOMITE -2009-



6-64Cylinder Head
Cylinder Head Installation (cont’d)
B
A
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft) A
B
A
B
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
12. Install the rocker arm assembly:
 K20Z2 engine (see page 6-60)
 K20Z3 engine (see page 6-61)
13. Install the cam chain (see page 6-21).
14. Connect the following engine wire harness connectors, and install the wire harness clamps to
the cylinder head:
 Four fuel injector connectors
 Engine coolant temperature (ECT) sensor 1 connector
 Camshaft position (CMP) sensor A (Intake) connector
 Camshaft position (CMP) sensor B (Exhaust) connector
 Rocker arm oil control valve connector
 Rocker arm oil pressure switch connector
 EVAP canister purge valve connector
 Variable valve timing control (VTC) oil control solenoid valve connector
 Exhaust gas recirculation (EGR) valve connector (K20Z2 engine)
 Engine oil pressure switch connector
15. Install the bolt (A) securing the connecting pipe.
16. Connect the water bypass hose (B). 17. Connect the upper radiator hose (A) and the heater
hoses (B).
18. Install the harness holder bracket (A), then install the harness holder (B).
08/08/21 14:28:43 61SNR030_060_0064
ProCarManuals.com
DYNOMITE -2009-





6-65
A
B6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
B
A A
B
19. Connect the positive crankcase ventilation (PCV)hose (A) (K20Z2 engine) and install the ground
cable (B).
20. Connect the fuel feed hose (A) (see page 11-331), then install the quick-connect fitting cover (B). 21. Connect the evaporative emission (EVAP) canister
hose (A) and the brake booster vacuum hose (B).
22. Install the exhaust manifold (see page 9-11).
23. Install the intake manifold:  K20Z2 engine (see page 9-4)
 K20Z3 engine (see page 9-9)
24. Install the drive belt (see page 4-31).
25. Install the air cleaner assembly (see page 11-345).
26. After installation, check that all tubes, hoses and connectors are installed correctly.
27. Inspect for fuel leaks. Turn the ignition switch to ON (II) (do not operate the starter) so that the fuel
pump runs for about 2 seconds and pressurizes the
fuel line. Repeat this operation three times, then
check for fuel leakage at any point in the fuel line.
(cont’d)
08/08/21 14:28:44 61SNR030_060_0065
ProCarManuals.com
DYNOMITE -2009-




Removal - K20Z3 engine
9-7
A
B C A
B
C
A B
C
1. Remove the engine cover.
2. Relieve the fuel pressure (see page 11-322).
3. Disconnect the vacuum hose (A) and the breather
pipe (B), then remove the intake air duct (C). 4. Disconnect the following engine wire harness
connectors, and remove the wire harness clamps
from the intake manifold:
 Four fuel injector connectors
 Manifold absolute pressure (MAP) sensor connector
 Throttle actuator connector
5. Remove the ground cable (A) and the harness clamp bracket (B), then remove the harness holder
(C) from the bracket.
6. Disconnect the positive crankcase ventilation (PCV) hose (A), the evaporative emission (EVAP) canister
hose (B) and the brake booster vacuum hose (C).
(cont’d)
08/08/21 14:37:34 61SNR030_090_0007
ProCarManuals.com
DYNOMITE -2009-

Î



9-8Intake Manifold and Exhaust System
Intake Manifold Removal and Installation (cont’d)
A
A
B A
B
A B
7. Disconnect the water bypass hoses (A), then plugthe water bypass hoses.
8. Remove the quick-connect fitting cover (A), then disconnect the fuel feed hose (B) (see page 11- 329).9. Raise the vehicle on the lift.
10. Remove the splash shield (see step 25 on page 5-5).
11. Remove the connector (A) from the intake manifold bracket (B), then remove the intake manifold
bracket.
12. Lower the vehicle on the lift.
13. Remove the intake manifold (A) from the cylinder head, then disconnect the water bypass hose (B).
08/08/21 14:37:34 61SNR030_090_0008
ProCarManuals.com
DYNOMITE -2009-






Î
Installation - K20Z3 engine
9-9
B A
C
8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft) B
A 8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) B
A
A
1. Connect the water bypass hose (A) to the intakemanifold (B), then install the intake manifold with a
new gasket (C), and tighten the bolts and the nuts in
a crisscross pattern in three steps, beginning with
the inner bolt.
2. Raise the vehicle on the lift.
3. Install the intake manifold bracket (A), then install the connector (B) to the intake manifold bracket.
4. Install the splash shield (see step 40 on page 5-20).
5. Lower the vehicle on the lift. 6. Connect the fuel feed hose (A) (see page 11-331),
then install the quick-connect fitting cover (B).
7. Connect the water bypass hoses (A).
(cont’d)
08/08/21 14:37:35 61SNR030_090_0009
ProCarManuals.com
DYNOMITE -2009-