2006 ACURA CSX center console


(#'



 ) Î
Î
(#'

 )
20-9620-96 Consoles
Center Console Armrest
Replacement
Armrest Lock Replacement
Fastener Locations
:Clip,5
A
A
B CFastener Locations
:TORXScrew,2
A
B
C
Fastener Locations :TORXScrew,2
NOTE: Take care not to scratch the armrest, center
console, and related parts.
1. Remove the center console (see page 20-92).
2. Gently pull out the center console rear cover (A) to detach the clips.
3. Open the armrest (A), pull the pin (B) off the armrest, then separate the armrest and the center
console (C).
4. Install the center console armrest in the reverse order of removal, and if the clips are damaged or
stress-whitened, replace them with new ones. NOTE: Take care not to scratch the armrest and related
parts.
1. Remove the center console armrest (see page 20-96).
2. Remove the screws with a TORX T15 bit. Slide the armrest liner (A) downward to release the hooks (B),
then remove the armrest liner and armrest spring
(C).
3. Remove the screws with a TORX T15 bit.
08/08/21 15:02:50 61SNR030_200_0098
ProCarManuals.com
DYNOMITE -2009-

(#'

 )
(#' )
S

pecial Tools Required
Special Tools Required
20-10820-108Dashboard
Side Defogger Vent Trim Removal/
Installation
Dashboard/Steering Hanger Beam
Removal/Installation
A
B C
KTC trim tool set SOJATP2014
NOTE:
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to scratch the dashboard and related parts.
1. Insert the trim tool into a gap between the side defogger vent trim (A) and the dashboard (B), and
release the hook (C).
2. Install the side defogger vent trim in the r everse
order of removal. KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Have an assistant help you when removing and installing the das hboard/steering hanger beam.
 Take care not to scratch the dashboard, the body and other related parts.
 Put on gloves to protect your hands.
1. Do the battery terminal disconnection procedure (see page 22-68), and wait at least 3 minutes before
beginning work.
2. Remove these items:  Driver’s dashboard lower cover (see page20-102)
 Driver’s dashboard undercover (see page 20- 103)
 Passenger’s dashboard undercover (see page 20-104)
 Center console (see page 20-92)
 Glove box (see page 20-104)
 Kick panel, both sides (see page 20-66)
 A-pillar trim, both sides (see page 20-69)
 Steering column (see page 17-10)
 EPS control unit (see page 17-84)
08/08/21 15:02:57 61SNR030_200_0110
ProCarManuals.com
DYNOMITE -2009-




(#'


)
22-296 Accessory Power Sockets
Front Accessory Power Socket Test/Replacement
BLK
WHT
A B
A
A
NOTE: If both of the front and console accessory power
sockets do not work, check the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box. 1. Remove the center panel.  With audio:– ’06-08 models (see page 23-80)
– ’09 model (see page 23-256)
 With navigation: – ’06-08 models (see page 23-155)
– ’09 model (see page 23-355)
2. Disconnect the 2P connector (A) from the front accessory power socket (B).
3. Inspect the connector terminals to be sure they are all making good contact.
 If the terminals are bent, loose, or corroded, repair them as necessary and recheck the system.
 IftheterminalslookOK,gotostep4.
4. Turn the ignition switch to ACC (I).
5. Measure the voltage between front accessory power socket 2P connector terminal No. 1 and body
ground. There should be battery voltage.
 If there is battery voltage, go to step 6.
 If there is no voltage, check for: – Blown No. 29 (15 A) fuse in the under-dash fuse/relay box.
– Faulty front accessory power socket relay.
– Poor ground (G 503).
– Anopeninthewire. 6. Check for continuity between front accessory
power socket 2P connector terminal No. 2 and body
ground. There should be continuity.
 If there is continuity, replace the power socket; go to step 7.
 If there is no continuity, check for: – Poor ground (G 502).
– Anopeninthewire.
7. Remove the socket (A).
8. Remove the housing (A) from the panel.
9. Install the front accessory power socket in the reverse order of removal.
Wire side of
female terminals
08/08/21 14:36:08 61SNR030_220_0298
ProCarManuals.com
DYNOMITE -2009-

Î


(#'



)
22-297
Console Accessory Power Socket Test/Replacement
BLK
YEL
A
B
A
A
NOTE: If both of the front and console accessory power
sockets do not work, check the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box. 1. Remove the center console (see page 20-95).
2. Disconnect the 2P connector (A) from the console accessory power socket (B).
3. Inspect the connector terminals to be sure they are all making good contact.
 If the terminals are bent, loose, or corroded, repair them as necessary and recheck the system.
 IftheterminalslookOK,gotostep4.
4. Turn the ignition switch to ACC (I), and measure the voltage between console accessory power socket
2P connector terminal No. 1 and body ground.
There should be battery voltage.
 If there is battery voltage, go to step 5.
 If there is no voltage, check for: – Blown No. 28 (15 A) fuse in the under-dash fuse/relay box.
– Faulty console accessory power socket relay.
– Poor ground (G 503).
– Anopeninthewire. 5. Check for continuity between console accessory
power socket 2P connector terminal No. 2 and body
ground. There should be continuity.
 If there is continuity, replace the power socket; go to step 6.
 If there is no continuity, check for: – Poor ground (G 601).
– Anopeninthewire.
6. Remove the socket (A).
7. Remove the housing (A) from the panel.
8. Install the console accessory power socket in the reverse order of removal.
Wire side of
female terminals
08/08/21 14:36:08 61SNR030_220_0299
ProCarManuals.com
DYNOMITE -2009-


(#'"


) 
(#'"

)
¦§¦§¦§¦§¦§¦§
¦§
Driver’s
22-30222-302 Seat Heaters
Switch Test/Replacement
Seat Heater Test
A
Driver’s seat heater switch
Front passenger’s seat heater switch
Terminal
Position
ON 1
HIGH LOW
OFF 2
2
3 3
4 4
5 5
6 6
7
: Front passenger’s seat heater switch A
B
1. Remove the center console front panel (see page20-92).
2. Disconnect the 6P (or 7P ) connector from the seat heater switch (A), then remove the switch.
*: Front passenger’s seat heater switch
3. Check for continuity between the terminals in each switch position according to the table.
4. If the continuity is not as specified, replace the switch.
5. Install the seat heater switch in the reverse order of removal. 1. Remove the driver’s seat (see page 20-118).
2. Disconnect the 3P connector (A) and 2P connector
(B) from the seat heater.
3. Check for continuity between seat-back heater 2P connector (female terminals) terminals No. 1 and
No. 2. There should be continuity.
Terminal side of
male terminals
Wire side of
female terminals
08/08/21 14:36:49 61SNR030_220_0304
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
 )
´
µ
Û
Ý

(#'





) Position Resistance
23-26223-262Audio System
USB Adapter Replacement
Audio Remote Switch Test
B
C
D
A
A
B
1. Remove the center console (see page 20-92).
2. Detach the USB adapter cable (A) from the clip.
Remove the cover (B) and disconnect the USB
adapter cable connector (C).
3. Carefully pull out the USB adapter holder (D) from the center console box.
4. Install the USB adapter in the reverse order of removal. SRS components are located in this area. Review the
SRS component location (see page 24-11).
Also review the precautions and procedures (see page
24-13) in the SRS section before doing repairs or
service.
1. Remove the driver’s airbag assembly (see page 24-188).
2. Remove the 20P connector (A) from the cable reel (B).
3. Measure the resistance between terminals No. 9 andNo.10ineachswitchpositionaccordingtothe
table.
No buttonpressed About 10 k
MODE About 3.7 k
CH ( ) About 1.7 k
CH ( ) About 775
(VOL.UP) About 357
(VOL.DOWN) About 100
4. If the resistance is not as specified, replace the audio remote switch (see page 23-263).
08/08/21 14:14:18 61SNR030_230_0265
ProCarManuals.com
DYNOMITE -2009-

Î
(#'#

)
Cavity Wire Test condition Test: Desired resultPossible cause if result is not obtained
Cavity Wire Test condition Test: Desired resultPossible cause if result is not obtained
23-388HandsFreeLink System
Control Unit Input Test/Replacement
B
A
WHT PUR
PNK
BLK
1. Remove the center console (see page 20-92).
2. Remove the console lower box (see page 20-95).
3. Disconnect the 28P connector (A) from the HandsFreeLink control unit (B).
4. Inspect the connector and socket terminals for a good pinfit to be sure they are all making good contact.
 If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
 IftheterminalslookOK,gotostep5.
5. Reconnect the connector and make these input tests at the connector.  If any test indicates a problem, find and correct the cause, then recheck the system.
 If all the input tests prove OK, go to step 6.






1 BLK Under all conditions Check for voltage to ground:
There should be less than 0.5 V.Poor ground (G501)
An open in the wire
15 WHT Under all conditions Check for voltage to ground: There should be battery voltage.Blown No. 23 (10 A) fuse in the
under-hood fuse/relay box
An open in the wire
16 PUR Ignition switch ON (II) Check for voltage to ground: There should be battery voltage.Blown No. 35 (7.5 A) fuse in the
under-dash fuse/relay box
An open in the wire
6. Disconnect the 28P connector again, and make this input test at the connector.  If the test indicates a problem, find and correct the cause, then recheck the system.
 If the input test proves OK, the HandsFreeLink control unit must be faulty, replace it.
18 PNK Under all conditions Check for continuity between No. 18 terminal and the driver’s under-dash
fuse/relay box connector Q (16P)
terminal No. 6:
There should be continuity.An open in the wire
Driver’s under-dash fuse/relay
box connector Q (16P)
disconnected Check for continuity to ground:
There should be no continuity.
Short to ground
Wire side of female terminals
08/08/21 14:18:43 61SNR030_230_0391
ProCarManuals.com
DYNOMITE -2009-



Seat Belt Tensioner
Seat Belt Buckle Tensioner SRS Unit
24-21
A
A B
A
7. Remove the B-pillar lower trim (see page 20-72).
Disconnect both floor wire harness 4P connectors
(A) from the seat belt tensioners.
8. Disconnect both floor wire harness 4P connectors (A), from the seat belt buckle tensioner. 9. Disconnect both seat belt buckle tensioner 4P
connectors and the both seat belt tensioner 4P
connector. Remove the center console (see page
20-92).Disconnect SRS unit connector A (28P) and B
(28P) from the SRS unit.
08/08/21 13:54:21 61SNR030_240_0021
ProCarManuals.com
DYNOMITE -2009-