2006 ACURA CSX relay

ignition dashboard wiper blades seat adjustment checking oil brake light

Page 2180 of 2893

ACURA CSX 2006 Service Repair Manual Cavity Wire Test conditionTest: Desired result Possible cause if desired result
is not obtained
22-230Wipers/Washers
MICU Input Test (cont’d)
5. Reconnect the connectors to the under-dash fuse/relay

Cavity Wire Test conditionTest: Desired result Possible cause if desired result
is not obtained
22-230Wipers/Washers
MICU Input Test (cont’d)
5. Reconnect the connectors to the under-dash fuse/relay box, and do these input tests at the following connectors.
If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, the MICU must be faulty; replace the under-dash fuse/relay box.

E6 BLK Under all conditions Measure the voltage to ground:
There should be less than 0.5 V.Poor ground (G602)
An open in the wire
E33 BLK Under all conditions Measure the voltage to ground: There should be less than 0.5 V.Poor ground (G601)
An open in the wire
F20 BLK Under all conditions Measure the voltage to ground: There should be less than 0.5 V.Poor ground (G401)
An open in the wire
T34 BLK Under all conditions Measure the voltage to ground: There should be less than 0.5 V.Poor ground (G501)
An open in the wire
S10 ·
S4 ORN
·
BLK Ignition switch ON (II),
windshield wiper/
washer switch (INT)
ON Measure the voltage between
terminals S10 and S4, and
terminals S20 and S4:
There should be less than 1 V. Faulty windshield wiper/
washer switch
An open in the wire
Ignition switch ON (II),
windshield wiper/
washer switch OFF Measure the voltage between
terminals S10 and S4, and
terminals S20 and S4:
There should be more than 5 V. Faulty windshield wiper/
washer switch
A short to ground in the wire
S15 ·
S4 GRN
·
BLK Ignition switch ON (II),
windshield wiper/
washer switch (MIST)
ON Measure the voltage between
terminals S15 and S4:
There should be less than 1 V.
Faulty windshield wiper/
washer switch
An open in the wire
Ignition switch ON (II),
windshield wiper/
washer switch (MIST)
OFF Measure the voltage between
terminals S15 and S4:
There should be more than 5 V.
Faulty windshield wiper/
washer switch
A short to ground in the wire
S17 ·
S4 YEL
·
BLK Ignition switch ON (II),
windshield washer
switch ON Measure the voltage between
terminals S17 and S4:
There should be less than 1 V. Faulty windshield wiper/
washer switch
An open in the wire
Ignition switch ON (II),
windshield washer
switch OFF Measure the voltage between
terminals S17 and S4:
There should be more than 5 V. Faulty windshield wiper/
washer switch
A short to ground in the wire
S20 ·
S4 WHT
·
BLK Ignition switch ON (II),
windshield wiper/
washer switch (LOW)
ON Measure the voltage between
terminals S20 and S4:
There should be less than 1 V.
Faulty windshield wiper/
washer switch
An open in the wire
Ignition switch ON (II),
windshield wiper/
washer switch OFF Measure the voltage between
terminals S20 and S4:
There should be more than 5 V. Faulty windshield wiper/
washer switch
A short to ground in the wire
Ignition switch ON (II),
windshield wiper/
washer switch (HIGH)
ON Measure the voltage between
terminals S20 and S4:
There should be less than 1 V.
Faulty windshield wiper/
washer switch
An open in the wire
Ignition switch ON (II),
windshield wiper/
washer switch OFF Measure the voltage between
terminals S20 and S4:
There should be more than 5 V. Faulty windshield wiper/
washer switch
A short to ground in the wire
08/08/21 14:28:48 61SNR030_220_0232
ProCarManuals.com
DYNOMITE -2009-