µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-91
45. Reconnect all connectors.
46. Turn the ignition switch to ON (II).
47. Clear the DTC with the HDS.
48. Start the engine.
49. With the brake pedal pressed, move the shift lever
through all positions. Stop for at least 1 second in
each position.
50. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wires between the transmission range switch
and the PCM, then go to step 1.
Go to step 51.
51. Monitor the OBD STATUS for P0705 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 50,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wires
between the transmission range switch and the
PCM, then go to step 1. If the HDS indicates NOT
COMPLETED, go to step 48.
52. Reconnect all connectors.
53. Update the PCM if it does not have the latest software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
54. Start the engine.
55. With the brake pedal pressed, move the shift lever through all positions. Stop for at least 1 second in
each position. 56. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wires between the transmission range switch
and the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-7), then go to step
54. If the PCM was substituted, go to step 1.
Go to step 57.
57. Monitor the OBD STATUS for P0705 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 56,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wires
between the transmission range switch and the
PCM. If the PCM was updated, substitute a known-
good PCM (see page 11-7), then go to step 54. If the
PCM was substituted, go to step 1. If the HDS
indicates NOT COMPLETED, go to step 54.
Is DT C P07 05 ind icated ?
Does the HDS ind icate PASSED? Is DT C P07 05 ind icated ?
Does the HDS ind icate PASSED?
08/08/21 14:41:01 61SNR030_140_0093
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P0706:
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
14-92
Automatic Transmission
DTC Troubleshooting (cont’d)
Open in Transmission Range
Switch Circuit
NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the
transmission.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Block the rear wheels and raise the front of the vehicle, make sure it is securely supported, and
allow the front wheels to rotate freely, or raise the
vehicle on a lift.
4. Start the engine, disable the VSA by pressing the VSA OFF switch (if equipped), run the vehicle with
the shift lever in D until the vehicle speed reaches
40 km/h (25 mph), then slow down and stop the
wheels.
5. Monitor the OBD STATUS for P0706 in the DTCs MENU with the HDS.
Go to step 6.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals between the
transmission range switch and the PCM. If the HDS
indicates NOT COMPLETED, go to step 4.
6. Turn the ignition switch to LOCK (0).
7. Inspect the transmission range switch (see page 14-265).
Go to step 8.
Replace the transmission range switch
(see page 14-267), then go to step 25.
8. Adjust the shift cable (see page 14-259). 9. Turn the ignition switch to ON (II).
10. Clear the DTC with the HDS.
11. Start the engine, disable the VSA by pressing the VSA OFF switch (if equipped), run the vehicle with
the shift lever in D until the vehicle speed reaches
40 km/h (25 mph), then slow down and stop the
wheels.
12. Monitor the OBD STATUS for P0706 in the DTCs MENU with the HDS.
Go to step 13.
If the HDS indicates PASSED, troubleshooting
is complete. If the HDS indicates NOT COMPLETED,
go to step 11.
13. Shift to D, and check the Forward Switch (ATPFWD) andA/TDSwitchintheDATALISTwiththeHDS.
Go to step 14.
Go to step 18.
14. Shift to S, and check the Forward Switch (ATPFWD) andA/TSSwitchintheDATALISTwiththeHDS.
Go to step 15.
Go to step 18.
Does the HDS ind icate F AILED?
Is the switch OK ? Does the HDS ind icate F AILED?
Ar e F or w ar d Sw i t ch ( AT PF W D) and A/ T D Sw i t chON?
Ar e F or w ar d Sw i t ch ( AT PF W D) and A/ T S Sw i t chON?
08/08/21 14:41:01 61SNR030_140_0094
ProCarManuals.com
DYNOMITE -2009-
µ
µ
µ
µ
YES
NO
YES
NO
14-93
TRANSMISSION RANGE
SWITCH CONNECTOR
GND (BLK)
15. Clear the DTC with the HDS.
16. Start the engine, disable the VSA by pressing theVSA OFF switch (if equipped), run the vehicle with
the shift lever in D until the vehicle speed reaches
40 km/h (25 mph), then slow down and stop the
wheels.
17. Monitor the OBD STATUS for P0706 in the DTCs MENU with the HDS.
Go to step 18.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals between the
transmission range switch and the PCM. If the HDS
indicates NOT COMPLETED, go to step 16.
18. Turn the ignition switch to LOCK (0).
19. Disconnect the transmission range switch connector. 20. Check for continuity between transmission range
switch connector terminal No. 10 and body ground.
Go to step 21.
Repair open in the wire between the
transmission range switch and body ground (G 101)
(see page 22-16), or repair poor body ground
(G101), then go to step 25.
21. Turn the ignition switch to ON (II).
(cont’d)
Wire side of female terminals
Does the HDS ind icate F AILED? Is there continuity?
08/08/21 14:41:01 61SNR030_140_0095
ProCarManuals.com
DYNOMITE -2009-
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
14-95
29. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the transmission range switch
and the PCM, then go to step 1.
Go to step 30.
30. Monitor the OBD STATUS for P0706 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 29,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the
transmission range switch and the PCM, then go to
step 1. If the HDS indicates NOT COMPLETED, go to
step 28.
31. Reconnect all connectors.
32. Update the PCM if it does not have the latest software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
33. Start the engine, disable the VSA by pressing the VSA OFF switch (if equipped), run the vehicle with
the shift lever in D until the vehicle speed reaches
48 km/h (30 mph), then slow down and stop the
wheels. 34. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the transmission range switch
and the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-7), then go to step
33. If the PCM was substituted, go to step 1.
Go to step 35.
35. Monitor the OBD STATUS for P0706 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 34,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the
transmission range switch and the PCM. If the PCM
was updated, substitute a known-good PCM
(see page 11-7), then go to step 33. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 33.
Is DT C P07 06 ind icated ?
Does the HDS ind icate PASSED? Is DT C P07 06 ind icated ?
Does the HDS ind icate PASSED?
08/08/21 14:41:02 61SNR030_140_0097
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
DTC P0711:
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
14-96
Automatic Transmission
DTC Troubleshooting (cont’d)
Problem in ATF Temperature
Sensor Circuit
NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the
transmission.
1. Turn the ignition switch to ON (II).
2. Check the ATF Temp Sensor in the Data List with the HDS.
Record the ATF temperature. Leave the
engine off for at least 30 minutes, then go to step 3.
Record the ATF temperature. Test the stall
speed RPM (see page 14-210) three times, then go
to step 3.
3. Check the ATF Temp Sensor in the Data List with the HDS.
Leave the engine off for at least 30 minutes,
then go to step 4.
Replace the ATF temperature sensor
(see page 14-229), then go to step 6.
4. Check the ECT Sensor in the Data List with the HDS.
Go to step 5.
Leave the engine off until ECT Sensor reads
the same as the outside air temperature, then go to
step 5. 5. Check the ATF Temp Sensor in the Data List with
the HDS.
Go to step 13.
Replace the ATF temperature sensor
(see page 14-229), then go to step 6.
6. Turn the ignition switch to ON (II).
7. Clear the DTC with the HDS.
8. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
9. Allow the engine coolant temperature to cool to the outside air temperature.
10. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on),
and wait for at least 20 seconds, then drive the
vehicle at speeds over 31 km/h (19 mph) for at least
5 minutes.
11. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the ATF temperature sensor and
thePCM,thengotostep1.
Go to step 12.
Does t he AT F t emper at ur e ex ceed t he out si d e ai rt emper at ur e?
Di d t he AT F t emper at ur e change?Does t he E CT Sensor r ead about t he same as t heout si d e ai r t emper at ur e? Does t he AT F t emper at ur e r ead about t he same as
ECT Sensor?
Is DTC P0711 indicated?
08/08/21 14:41:02 61SNR030_140_0098
ProCarManuals.com
DYNOMITE -2009-
µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
14-97
12. Monitor the OBD STATUS for P0711 in the DTCs
MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 11,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the ATF
temperaturesensorandthePCM,thengotostep1.
If the HDS indicates NOT COMPLETED, go to step 8.
13. Update the PCM if it does not have the latest software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
14. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
15. Allow the engine coolant temperature to cool to the outside air temperature.
16. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on),
and wait for at least 20 seconds, then drive the
vehicle at speeds over 31 km/h (19 mph) for at least
5 minutes.
17. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the ATF temperature sensor and
the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-7), then go to step
14. If the PCM was substituted, go to step 1.
Go to step 18. 18. Monitor the OBD STATUS for P0711 in the DTCs
MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 17,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the ATF
temperature sensor and the PCM. If the PCM was
updated, substitute a known-good PCM (see page
11-7), then go to step 14. If the PCM was substituted,
go to step 1. If the HDS indicates NOT COMPLETED,
go to step 14.
Does the HDS ind icate PASSED?
Is DTC P0711 indicated? Does the HDS ind icate PASSED?
08/08/21 14:41:02 61SNR030_140_0099
ProCarManuals.com
DYNOMITE -2009-
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
14-99
11. Reconnect all connectors.
12. Turn the ignition switch to ON (II).
13. Clear the DTC with the HDS.
14. Start the engine with the shift lever in P, and wait
for at least 20 seconds.
15. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wire between the ATF temperature sensor
and the PCM, then go to step 1.
Go to step 16.
16. Monitor the OBD STATUS for P0712 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 15,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wire
between the ATF temperature sensor and the PCM,
then go to step 1. If the HDS indicates NOT
COMPLETED, go to step 14.
17. Reconnect all connectors.
18. Update the PCM if it does not have the latest software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
19. Start the engine with the shift lever in P, and wait for at least 20 seconds. 20. Check for Temporary DTCs or DTCs with the HDS.
Check for intermittent short to body ground
in the wire between the ATF temperature sensor
and the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-7), then go to step
19. If the PCM was substituted, go to step 1.
Go to step 21.
21. Monitor the OBD STATUS for P0712 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 20,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for
intermittent short to body ground in the wire
between the ATF temperature sensor and the PCM.
If the PCM was updated, substitute a known-good
PCM(seepage11-7),thengotostep19.IfthePCM
was substituted, go to step 1. If the HDS indicates
NOT COMPLETED, go to step 19.
Is DTC P0712 indicated?
Does the HDS ind icate PASSED? Is DTC P0712 indicated?
Does the HDS ind icate PASSED?
08/08/21 14:41:03 61SNR030_140_0101
ProCarManuals.com
DYNOMITE -2009-
Î Î
µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
14-101
SG2 (GRN/BLK)
JUMPER WIRE
SHIFT SOLENOID WIRE HARNESS CONNECTOR
PCM CONNECTOR B (44P) SG2 (GRN/BLK) PCM CONNECTOR B (44P)
TATF (RED/YEL)
SHIFT SOLENOID
WIRE HARNESS
CONNECTOR
TATF
(RED/YEL)
12. Turn the ignition switch to LOCK (0).
13. Jump the SCS line with the HDS.
14. Disconnect PCM connector B (44P).
15. Connect shift solenoid wire harness connector terminal No. 7 and body ground with a jumper wire.
16. Check for continuity between PCM connector terminal B33 and body ground.
Go to step 27.
Repair open in the wire between PCM
connector terminal B33 and the ATF temperature
sensor,thengotostep21. 17. Turn the ignition switch to LOCK (0).
18. Jump the SCS line with the HDS.
19. Disconnect PCM connector B (44P).
20. Check for continuity between PCM connector
terminal B27 and shift solenoid wire harness
connector terminal No. 6.
Go to step 27.
Repair open in the wire between PCM
connector terminal B27 and the ATF temperature
sensor,thengotostep21.
21. Reconnect all connectors.
22. Turn the ignition switch to ON (II).
23. Clear the DTC with the HDS.
24. Start the engine with the shift lever in P, and wait for at least 20 seconds.
25. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the ATF temperature sensor and
thePCM,thengotostep1.
Go to step 26.
(cont’d)
Wire side of female terminals
Terminal side of female terminals Wire side of
female terminals
Terminal side of
female terminals
Is there continuity? Is there continuity?
Is DTC P0713 indicated?
08/08/21 14:41:04 61SNR030_140_0103
ProCarManuals.com
DYNOMITE -2009-