Page 1679 of 2893
(#'
)
20-920-9
Front Door Outer Handle
Replacement
A B
62 mm (2.44 in.)
A
B C
B
A
10. Install the door panel in the r everse order of
removal, and note these items:
If the clips are damaged or stress-whitened, replace them with new ones.
Replace any damaged cable fasteners with new ones.
The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
Make sure the connectors are plugged in properly, and the cables are connected securely.
Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel and inner handle (see page 20-7).
3. Disconnect the power door lock actuator connector (A).
4. Remove the plug caps (B), then remove the plastic cover (C), as needed.
5. Detach the rod fastener (A).
(cont’d)
08/08/21 14:58:59 61SNR030_200_0011
ProCarManuals.com
DYNOMITE -2009-
Page 1684 of 2893
(#'
)
20-14 Doors
Front Door Glass and Regulator Replacement
E
D
A B
EF B
D
C
Fastener Locations :Bolt,2
A
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) A
B
C
D
E
E
D
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) Fastener Locations
:Bolt,2
D:Bolt,2 E
(Black) (Gold)
NOTE: Put on gloves to protect your hands.
1. Remove the door panel (see page 20-7).
2. Disconnect the power door lock actuator connector (A) and remove the plug caps (B).
3. Pass the cables (C) and the harnesses (D) through the slits (E) in the plastic cover (F), then remove the
plastic cover.
4. Carefully raise the glass (A) until you can see the bolts, then remove them. Carefully pull the glass
out through the window slot. Take care not to drop
the glass inside the door. 5. Disconnect the connector (A), and detach the
harness clip (B) from the regulator (C).
6. Remove the bolts (D), and loosen the bolts (E), then remove the regulator through the hole in the door.
08/08/21 14:59:02 61SNR030_200_0016
ProCarManuals.com
DYNOMITE -2009-
Page 1685 of 2893
(#'
)
20-1520-15
Front Door Glass Outer
Weatherstrip Replacement
A A B
B
A
A
7. Apply multipurpose grease to all the sliding surfaces of the regulator (A) where shown.
8. Install the glass and regulator in the reverse order of removal, and note these items:
Roll the glass up and down to verify it moves freely without binding.
Make sure that there is no clearance between the glass and glass run channel when the glass is
closed.
Adjust the position of the glass as necessary (see page 20-28).
When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
Check for water leaks (see step 9 on page 20-29).
Make sure the power door locks, the windows and the power mirror operate properly.
Test-drive and check for wind noise and rattles. NOTE:
Put on gloves to protect your hands.
Take care not to scratch the door.
1. Lower the glass fully.
2. Release the front hook (A) from inside of the door, then pull up the front door glass outer weatherstrip
(B).
3. Starting at the front, slowly pull up the front door glass outer glass weatherstrip (A).
(cont’d)
08/08/21 14:59:02 61SNR030_200_0017
ProCarManuals.com
DYNOMITE -2009-
Page 1686 of 2893
(#'
)
20-1520-15
Front Door Glass Outer
Weatherstrip Replacement
A A B
B
A
A
7. Apply multipurpose grease to all the sliding surfaces of the regulator (A) where shown.
8. Install the glass and regulator in the reverse order of removal, and note these items:
Roll the glass up and down to verify it moves freely without binding.
Make sure that there is no clearance between the glass and glass run channel when the glass is
closed.
Adjust the position of the glass as necessary (see page 20-28).
When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
Check for water leaks (see step 9 on page 20-29).
Make sure the power door locks, the windows and the power mirror operate properly.
Test-drive and check for wind noise and rattles. NOTE:
Put on gloves to protect your hands.
Take care not to scratch the door.
1. Lower the glass fully.
2. Release the front hook (A) from inside of the door, then pull up the front door glass outer weatherstrip
(B).
3. Starting at the front, slowly pull up the front door glass outer glass weatherstrip (A).
(cont’d)
08/08/21 14:59:02 61SNR030_200_0017
ProCarManuals.com
DYNOMITE -2009-
Page 1689 of 2893
(#'
)
Special Tools Required
20-17
Rear Door Panel Removal/Installation
A
B
C
Fastener Locations :Screw,1 :Clip,1
AFa
stener Location
:Clip,1
A B
C
D
B
A
Fastener Location :Screw,1
KTC trim tool set SOJATP2014
NOTE: Use the appropriate tool from the KTC trim tool
s
et to avoid damage when removing components.
1. Raise the glass fully.
2. Pry out on the rear portion of the inner handle cap (A) with the appropriate trim tool, then release the
hooks (B, C).
3. Remove the screw and clip securing the inner handle (A). 4
. Remove the power window switch panel (A).
–1 Pry up on the rear edge of the switch panel with the appropriate trim tool, then release the
rear clip.
–2 Pull out along the edge of the panel to release the hooks (B).
–3 Pull the switch panel rearward to release the front hook (C).
–4 Disconnect the power window switch connector (D).
5. Remove the screw.
(cont’d)
08/08/21 14:59:04 61SNR030_200_0019
ProCarManuals.com
DYNOMITE -2009-
Page 1691 of 2893
(#'
)
20-1920-19
Rear Door Outer Handle
Replacement
A B
62 mm (2.44 in.) A
B
C
D C
A
10. Install the door panel in the r everse order of
removal, and note these items:
If the clips are damaged or stress-whitened, replace them with new ones.
Replace any damaged cable fasteners with new ones.
The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
Make sure the connector is plugged in properly, and the cables are connected securely.
Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Detach the harness clip (A), and disconnect the power door lock actuator connector (B).
4. Remove the plug caps (C), then remove the plastic cover (D), as needed.
5. Remove the latch mounting screws, then lower the latch (see step 4 on page 20-21).
6. Detach the rod fastener (A).
(cont’d)
08/08/21 14:59:06 61SNR030_200_0021
ProCarManuals.com
DYNOMITE -2009-
Page 1692 of 2893
(#'
)
20-1920-19
Rear Door Outer Handle
Replacement
A B
62 mm (2.44 in.) A
B
C
D C
A
10. Install the door panel in the r everse order of
removal, and note these items:
If the clips are damaged or stress-whitened, replace them with new ones.
Replace any damaged cable fasteners with new ones.
The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
Make sure the connector is plugged in properly, and the cables are connected securely.
Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Detach the harness clip (A), and disconnect the power door lock actuator connector (B).
4. Remove the plug caps (C), then remove the plastic cover (D), as needed.
5. Remove the latch mounting screws, then lower the latch (see step 4 on page 20-21).
6. Detach the rod fastener (A).
(cont’d)
08/08/21 14:59:06 61SNR030_200_0021
ProCarManuals.com
DYNOMITE -2009-
Page 1698 of 2893
20-24
Doors
Rear Door Glass and Regulator Replacement (cont’d)
A
B C
D
E
B
A B A
A A
B
B
A
6. Pull the glass run channel (A) away as needed. Pull
the rear lower channel (B) forward from the quarter
glass seal (C) then release the upper hook (D) from
the door. Remove the rear lower channel from the
rear door glass (E), then pull the channel up to
remove it.
7. Remove the rear lower channel (A) from the glass run channel (B). 8. Carefully remove the glass (A) out through the
window slot. Take care not to drop the glass inside
the door.
9. Remove the quarter glass (A). Take care not to damage the outer weatherstrip (B).
08/08/21 14:59:09 61SNR030_200_0026
ProCarManuals.com
DYNOMITE -2009-
