2006 ACURA CSX wheel alignment

Î
16-22Driveline/Axle
Driveshaft Installation (cont’d)
B
A
K20Z2 engine model:
22x1.5mm
181 N·m
(18.5 kgf·m, 134 lbf·ft)
K20Z3 engine model:
24x1.5mm
245 N·m
(25.0 kgf·m, 180 lbf·ft)
9. Apply small amount of engine oil to the seating surface of new spindle nut (A).
10. Install the spindle nut, then tighten it. After tightening, use a drift to stake the spindle nut
shoulder (B) against the driveshaft.
11. Clean the mating surfaces of the brake disc and the wheel, then install the front wheels.
12. Turn the front wheel by hand, and make sure there is no interference between the driveshaft and
surrounding parts. 13. Refill the transmission with the recommended
transmission fluid:
 5-speed manual transmission (see page 13-5)
 6-speed manual transmission (see page 13-82)
 Automatic transmission (see page 14-232)
14. Lower the vehicle on the lift.
15. Check the wheel alignment, and adjust it if necessary (see page 18-5).
16. Test-drive the vehicle.
Replace.
Replace.
08/08/21 14:51:45 61SNR030_160_0022
ProCarManuals.com
DYNOMITE -2009-



16-28Driveline/Axle
Intermediate Shaft Installation (cont’d)
A
10x1.25mm
39N·m(4.0kgf·m,29lbf·ft)
B
10x1.25mm
39 N·m
(4.0 kgf·m,
29 lbf·ft)
8x1.25mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
4. Install the flange bolt (A) and two shoulder bolts (B).
5. Install the heat shield, and tighten and three bolts.
6. Install the right driveshaft (see page 16-20).
7. Refill the transmission with the recommended transmission fluid:
 5-speed manual transmission (see page 13-5)
 6-speed manual transmission (see page 13-82)
 Automatic transmission (see page 14-232)
8. Check the wheel alignment, and adjust it if necessary (see page 18-5).
9. Test-drive the vehicle.
08/08/21 14:51:48 61SNR030_160_0028
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
Special Tools Required
17-16
Steering
Tie-rod End Ball Joint Boot Replacement
C
D
D
A
B
E A
B
07JAF-SH20330
Bushing base 07JAF-SH20330
1. Disconnect the tie-rod end ball joint from the knuckle (see step 17 on page 17-67).
2. Remove the tie-rod end from the rack end.
3. Remove the tie-rod ball joint boot from the tie-rod end, and wipe the old grease off the ball pin.
4. Pack the lower area of the ball pin (A) with fresh multipurpose grease.
5. Pack the interior of the new tie-rod end ball joint boot (B) and lip (C) with fresh multipurpose grease.
Note these items when installing new grease: Keep grease off the boot mounting area (D) and the tapered section (E) of the ball pin.
 Do not allow dust, dirt, or other foreign materials to enter the boot. 6. Install the new tie-rod end ball joint boot (A) using
the bushing base. The boot must not have a gap at
the boot installation sections (B). After insta lling the
boot, check the ball pin tapered section for grease
contamination, and wipe it if necessary.
7. Install the tie-rod end to the rack end.
8. Connect the tie-rod end ball joint to the knuckle (see step 25 on page 17-76).
9. Check the wheel alignment, and adjust it if necessary (see page 18-5).
08/08/21 14:53:19 61SNR030_170_0017
ProCarManuals.com
DYNOMITE -2009-




(#'

 )
17-17
Gearbox Mount Cushion Replacement
A
B
C
D
E A
B
A
A
1. Remove the steering gearbox (see page 17-65).
2. Position a 34 mm socket wrench (A) on the flange part of the gearbox housing with a washer (B), a
10 x 105 mm flange bolt (C), and a 10 mm nut (D) as
shown.
3. Hold the 10 mm nut with a wrench, and tighten the 10 x 105 mm flange bolt with another wrench.
Remove the gearbox mount cushion (E). 4. Apply a mild soap and water solution to the new
gearbox mount cushion surface (A), then place the
mount cushion on the gearbox mounting cushion
hole.
5. Using a flat-tipped screwdriver, push the edge of the mount cushion (B) until it is about 1/3 of the
way into the gearbox housing.
NOTE: Be careful not to damage the surface of the
mount cushion when pushing it with the flat-tipped
screwdriver.
6. Position a 34 mm socket wrench on the flange part of the gearbox housing with a washer, flange bolt,
and the nut as shown.
7. Install the gearbox mount cushion by tightening the nut until the mount cushion edges (A) contact the
gearbox flange surface.
8. Install the steering gearbox (see page 17-72).
9. Check the wheel alignment, and adjust it if necessary (see page 18-5).
Replace.
08/08/21 14:53:20 61SNR030_170_0018
ProCarManuals.com
DYNOMITE -2009-

SymptomProbable cause
17-78EPS Components
Steering Gearbox Removal and Installation (cont’d)
34. Install the steering wheel (see page 17-8).
35. With the tires raised off the ground (vehicle on a
lift), check for the following symptoms by turning
the steering wheel fully to the right and left several
times.
Rubbing sound
coming from the
lower steering
column area. Steering column joint
is contacting the cover.
Grating sound from
the lower steering
column area, or a
rough feeling during
steering. Poor engagement of
the pinion shaft
serrations.
Noise from around
the steering wheel
during steering. Poor engagement of
the SRS cable reel with
the steering wheel, or a
damaged cable reel.
36. Install the air cleaner housing (see page 11- 345).
37. Install the under cowl panel and cowl cover (see page 20-163). 38. Do the battery terminal reconnection procedure
(see page 22-68), and do these tasks:
 Turn the ignition switch to ON (II) and check that the SRS indicator comes on for about 6 seconds
and then goes off.
 Make sure the horn and turn signal switches work properly.
 Make sure the steering wheel switches work properly.
39. After installation, do the following checks:  Check the steering wheel spoke angle. If steeringspoke angles to the right and left are not equal
(steering wheel and rack are not centered),
correct the engagement of the joint/pinion shaft
splines.
 Set the steering column to the center tilt position, and to the center telescopic position, then check
the wheel alignment and adjust (see page 18-5).
 Make sure the steering wheel spokes are centered.
 Start the engine, and let it idle. Turn the steering wheel from lock-to-lock several times. Check that
the EPS indicator does not come on.
 Do the memorizing for the torque sensor neutral position (see page 17-22).
08/08/21 14:55:18 61SNR030_170_0079
ProCarManuals.com
DYNOMITE -2009-

(#'

/)
Suspension
Front and Rear Suspension
Front Suspension
Rear Suspension............................................. .............................................
TPMS (Tire Pressure Monitoring System)
(’08-09 Models) . 18-47
................................................................
........................................
......................................................... ...........................
...........................................
............................................
...................................................... ...................
................................................................
........................................
......................................................... ...........................
...........................................
............................................
...................................................... ...................
Special Tools . 18-2
Component Location Index . 18-3
Wheel Alignment . 18-5
Wheel Bearing End Play Inspection . 18-9
Wheel Runout Inspection . 18-9
Wheel Bolt Replacement . 18-10
Ball Joint Removal . 18-12
Ball Joint Boot Inspection/Replacement . 18-13
...............
................................... ............................... ..........................
........................................ .................
................................... ...............
................................... ............................... ..........................
........................................ .................
...................................
Knuckle/Hub/Wheel Bearing Replacement . 18-14
Lower Ball Joint Replacement
. 18-20
Lower Arm Removal/Installation . 18-22
Stabilizer Link Removal/Installation . 18-25
Stabilizer Bar Replacement . 18-25
Damper/Spring Removal and Installation . 18-26
Damper/Spring Disassembly, Inspection, and Reassembly . 18-28
...................
............................... ............................. ..........................
........................................
.................................................
.................................................... ...................
............................... ............................. ..........................
........................................
.................................................
....................................................
Knuckle/Hub Bearing Unit Replacement
. 18-31
Upper Arm Removal/Installation . 18-35
Trailing Arm Removal/Installation . 18-36
Stabilizer Link Removal/Installation . 18-37
Stabilizer Bar Replacement . 18-38
Damper Replacement . 18-39
Spring Replacement . 18-42
08/08/21 14:56:38 61SNR030_180_0001
ProCarManuals.com
DYNOMITE -2009-


(#'") ¶
Pre-Alignment Checks
Caster Inspection
Tire size (’06-08 models):Except Type S model:Front/Rear: P205/55R16 89H
Type S model: Front/Rear: P215/45R17 87V
Tire size (’09 model): Front/Rear: P215/45R17 87V
Tire Pressure (’06-08 models) (at cold): Except Type S model:Front/Rear: 220 kPa (2.2 kgf/cm , 32 psi)
Type S model: Front/Rear: 230 kPa (2.3 kgf/cm , 33 psi)
Tire Pressure (’09 model) (at cold): Front/Rear: 230 kPa (2.3 kgf/cm , 33 psi) Caster angle: 7 ° 00 ’ 1 °
2
2
2
18-5
Wheel Alignment
The suspension can be adjusted for front camber, front
toe, and rear toe. However, each of these adjustments
are related to each other. For example, when you adjust
camber, the toe will change. Therefore, you must adjust
the front wheel alignment whenever you adjust camber
or toe.
For proper inspection and adjustment of the wheel
alignment, do these checks: 1. Release the parking brake to avoid an incorrect measurement.
2. Make sure the suspension is not modified.
3. Make sure the fuel tank is full, and that the spare tire, the jack, and the tools are in place on the
vehicle.
4. Check the tire size and tire pressure.
5. Check the runout of the wheels and tires (see page 18-9). 6. Check the suspension ball joints (Hold a tire with
your hands, and move it up and down and right and
left to check for movement).
7. Before doing alignment inspections, be sure to remove all extra weight from the vehicle, and no
one should be inside the vehicle (driver or
passengers).
8. Bounce the vehicle up and down several times to stabilize the suspension.
9. Check that the steering column is set at the center tilt and telescopic position.
Use commercially available computerized four wheel
alignment equipment to measure wheel alignment
(caster, camber, toe, and turning angle). Follow the
equipment manufacturer’s instructions. 1. Check the caster angle.
 If the measurement is within specifications,measure the camber angle.
 If the measurement is not within specifications, check for bent or damaged suspension
components.
(cont’d)
08/08/21 14:56:45 61SNR030_180_0005
ProCarManuals.com
DYNOMITE -2009-




¶
µ
µ
´ µ
´ µ
Camber Inspection Front Camber Adjustment
Camber angle:
Front: 0 ° 00 ’ 30 ’
(Maximum difference between the front right and left
side: 0 ° 35 ’) Rear (without ‘‘C’’ marks on the upper arm):1°30’
Rear (with ‘‘C’’ marks on the upper arm): 0°45’
1° 05 ’ 0° 45 ’
1° 05 ’ 0° 45 ’
18-6Front and Rear Suspension
Wheel Alignment (cont’d)
A
Damper pinch bolt Adjusting bolt set:
P/N 04512-SNA-305
A
14x1.5mm
90 N·m
(9.2 kgf·m,
67 lbf·ft)
Use commercially available computerized four wheel
alignment equipment to measure wheel alignment
(caster, camber, toe, and turning angle). Follow the
equipment manufacturer’s instructions.1. Check the camber angle. NOTE: There are two types of rear upper arms. Those that are marked with ‘‘C’’ (A), and those with no
marks. Be sure to use the correct alignment
specifications.
 If the measurement is within specification, measure the toe-in.
 If the measurement for the front camber is outside the specification, go to front camber
adjustment.
 If the measurement for the rear camber is outside the specification, check for bent or damaged
suspension components. The front camber can be adjusted by exchanging one or
both of the damper pinch bolts with a smaller diameter
adjusting bolt. The difference between the adjusting
bolt diameter and the pinch bolt hole diameter allows
for a small range of adjustment.
1. Raise the front of the vehicle, and support it with safety stands in the proper locations (see page
1-11).
2. Remove the front wheels.
3. Loosen the damper pinch bolts (A), and adjust the camber angle by moving the bottom of the damper
within the range of the damper pinch bolt free play.
4. Tighten the damper pinch bolts to the specified torque.
5. Clean the mating surfaces of the brake disc and the inside of the wheel, then install the front wheels.
6. Lower the vehicle to the ground, and bounce the front of the vehicle up and down several times to
stabilize the suspension.
Replace.
08/08/21 14:56:45 61SNR030_180_0006
ProCarManuals.com
DYNOMITE -2009-