2006 ACURA CSX maintenance reset

Î
 
(#'



 )
Automatic Transmission Fluid Capacity:
2.9 L (3.1 US qt) at change
6.5 L (6.9 US qt) at overhaul
14-232 Automatic Transmission
ATF Replacement
A
18 x 1.5 mm
49 N·m
(5.0 kgf·m,
36 lbf·ft)
B
ATF
A
NOTE: Keep all foreign particles out of the transmission. 1. Park the vehicle on the level ground.
2. Warm up the engine to normal operating temperature (the radiator fan comes on), and turn
the engine off.
3. Remove the drain plug (A), and drain the automatic transmission fluid (ATF).
4. Reinstall the drain plug with a new sealing washer (B).
5. Refill the transmission with ATF into the dipstick hole to bring the fluid level between the upper
mark and the lower mark of the dipstick. Always
use Acura ATF-Z1 automatic transmission fluid
(ATF). Using a non-Acura ATF can affect shift
quality.
6. Check that the ATF level is between the upper mark
and the lower mark of the dipstick.
7. Insert the dipstick back into the transmission with the letters ‘‘ATF’’ pointing toward the front of the
vehicle. 8. If the maintenance minder required to replace the
ATF, reset the maintenance minder (see page 3-4),
and this procedure is complete. If the maintenance
minder did not require you to replace the ATF, go
to step 9.
9. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
10. Turn the ignition switch to ON (II). Make sure the HDS communicates with the PCM. If it does not, go
to the DLC circuit troubleshooting (see page
11-204).
11. Select BODY ELECTRICAL with the HDS.
12. Select ADJUSTMENT in the GAUGES MENU with the HDS.
13. Select RESET in the MAINTENANCE MINDER MENU with the HDS.
14. Select RESETTING THE ATF with the HDS.
NOTE: If you changed the engine oil at the same
time with the ATF, select RESETTING THE ENGINE
OIL LIFE AND ATF with the HDS instead.
Replace.
08/08/21 14:46:53 61SNR030_140_0234
ProCarManuals.com
DYNOMITE -2009-

Entry Lights Control System
Power Windows
Wipers/Washers
GaugesReminder Systems
Moonroof
Accessory Power Sockets
Seat Heaters
Power Mirrors
Rear Window Defogger
Immobilizer System......................
.......................................... ......................................... ...........................
.............................. ......................
.......................................... ......................................... ...........................
..............................
Component Location Index . 22-202
Circuit Diagram . 22-203
MICU Input Test . 22-204
Ignition Key Switch Test . 22-207
Ignition Key Light Test . 22-207
......................
...................................
............................................ ..........................................
.......................................................... ........
.......................................................... ..................................
........................................................
...................................
............................................ ..........................................
.......................................................... ........
.......................................................... ..................................
..................................
Component Location Index
. 22-208
System Description . 22-209
Resetting the Power Window Control Unit . 22-210
Circuit Diagram . 22-212
Power Window Master Switch Input Test . 22-214
Driver’s Power Window Motor Test . 22-217
Passenger’s Power Window Motor Test . 22-218
Power Window Master Switch Test/Replacement . 22-219
Passenger’s Power Window Switch Test/Replacement . 22-220
......................
.......................................... ................................
......................................... .......................
....................................... .................................... ...............
....................... ........
...............
........................ ................
...................... ......................
.......................................... ................................
......................................... .......................
....................................... .................................... ...............
....................... ........
...............
........................ ................
......................
Component Location Index
. 22-221
Circuit Diagram . 22-223
DTC Troubleshooting . 22-224
MICU Input Test . 22-228
Wiper/Washer Switch Test . 22-231
Wiper Motor Test . 22-231
Washer Motor Test . 22-232
Washer Fluid Level Switch Test . 22-232
Wiper Motor Replacement . 22-233
Wiper/Washer Switch Replacement . 22-234
Washer Reservoir Replacement . 22-234
Wiper Blade Replacement . 22-235
Wiper Arm/Nozzle Adjustment . 22-236
Washer Tube Replacement . 22-237
......................
...........................
.......................................... ................................
................................................
................................................
......................................
..............................................
..................................
.............................................. ......................
...........................
.......................................... ................................
................................................
................................................
......................................
..............................................
..................................
..............................................
Component Location Index
. 22-238
Self-diagnostic Function . 22-241
Circuit Diagram . 22-244
DTC Troubleshooting . 22-262
Gauge Control Module (Tach) Input Test . 22-271
Gauge Control Module (Speedo) Input Test . 22-274
Rewriting the ODO Data and Transferring the Maintenance
Minder Data to a New Gauge
Control Module . 22-276
Replacement . 22-277
Dash Lights Brightness Controller and Odometer Select/Reset Switch
Test/Replacement . 22-278
Outside Air Temperature Indicator Calibration . 22-279 ......................
.......................................... ......................................... ......................
.......................................... .........................................
Component Location Index
. 22-281
Circuit Diagram . 22-282
MICU Input Test . 22-284
...................... ......
.......................................... ...................
......................
......
.......................................... ...................
Component Location Index
. 22-286
Resetting the Moonroof Control Unit . 22-287
Circuit Diagram . 22-288
Moonroof Control Unit Input Test . 22-290
Moonroof Switch Test/Replacement . 22-293
......................
..........................................
..................................
.................................. ......................
..........................................
..................................
..................................
Component Location Index
. 22-294
Circuit Diagram . 22-295
Front Accessory Power Socket Test/Replacement . 22-296
Console Accessory Power Socket Test/Replacement . 22-297
......................
.......................................... .........................
........................................ ......................
.......................................... .........................
........................................
Component Location Index
. 22-298
Circuit Diagram . 22-300
Switch Test/Replacement . 22-302
Seat Heater Test . 22-302
......................
..........................................
..............................................
........................................................ .......
......................
..........................................
..............................................
........................................................ .......
Component Location Index
. 22-304
Circuit Diagram . 22-305
Function Test . 22-306
Power Mirror Switch Test/Replacement . 22-307
Power Mirror Actuator Test . 22-307
Power Mirror Actuator Replacement . 22-308
......................
..........................................
.............................................. ......................................................
..........................................
.............................................. ................................
Component Location Index
. 22-310
Circuit Diagram . 22-311
Function Test . 22-312
Defogger Wire Repair . 22-313
......................
...................................
.......................................... ................................
............................................. ......................
............................................
.................................................. ...................
................................................ ........................................... ......................
...................................
.......................................... ................................
............................................. ......................
............................................
.................................................. ...................
................................................ ...........................................
Component Location Index
. 22-314
System Description . 22-315
Circuit Diagram . 22-316
DTC Troubleshooting . 22-317
Symptom Troubleshooting Information . 22-321
Symptom Troubleshooting . 22-323
System Check . 22-326
Status Log . 22-328
Immobilizer Key Registration . 22-329
Immobilizer-Keyless Control Unit Input Test . 22-330
Immobilizer-Keyless Control Unit Replacement . 22-332
08/08/21 14:22:03 61SNR030_220_0003
ProCarManuals.com
DYNOMITE -2009-

µ
µ
HDS Inputs and Commands
Input:System Menu Data List Data List Indication
22-88Multiplex Integrated Control System
System Description (cont’d)
Certain inputs happen so quickly that the HDS cannot update fast enough. Hold the switch that is being tested while monitoring the Data List.
This should give the HDS time to update the signal on the Data List.
Because the HDS software is updated to support the release for newer vehicles it is not uncommon to see system function tests that are not
supported.
Make sure that the most current software is loaded.
Gauges Cruise Control Main Switch OFF/ON Cruise Control Set Switch OFF/ON
Cruise Control Resume Switch OFF/ON
Washer Fluid Level Switch OFF/ON
VSA/TCS Off Switch OFF/ON
Gauge Select/Reset Switch OFF/ON
Parking Brake Switch OFF/ON
Brake Fluid Level Switch OFF/ON
Illumination Volume Plus Switch OFF/ON
Illumination Volume Minus Switch OFF/ON
Km/h mph Select Switch OFF/ON
Fuel Sending Unit Input 1 deg
Fuel Sending Unit Input 2 VOLTAGE
VSA/TCS Active Indicator OFF/ON
VSA/TCS Indicator (Warning) OFF/ON
ABS Indicator OFF/ON
Cruise Control Main Switch Indicator OFF/ON
MIL Indicator OFF/ON
Washer Fluid Level Indicator OFF/ON
DRL Indicator OFF/ON
Low Oil Pressure Indicator OFF/ON
Charging System Indicator OFF/ON
Cruise Main Switch ON Indicator OFF/ON
Maintenance Minder Indicator OFF/ON
High Beam Indicator OFF/ON
Parking Light ON Indicator OFF/ON
Low Fuel Warning Indicator OFF/ON
Security Indicator OFF/ON
Fog Light Indicator OFF/ON
Seat Belt Indicator OFF/ON
Speed Indicator (km/h) 0 249 km/h, over 250 km/h, Fail
Speed Indicator (mph) 0 154 mph, over 155 mph, Fail
Low Tire Pressure Indicator OFF/ON
TPMS Indicator OFF/ON
A/TGearPositionSwitch(R) OFF/ON
A/TGearPositionSwitch(P) OFF/ON
08/08/21 14:24:09 61SNR030_220_0090
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#'
)
22-238Gauges
Component Location Index
OIL PRESSURE SWITCH
ECM/PCMBRAKE FLUID LEVEL SWITCH
FUEL GAUGE SENDING UNIT
GAUGE CONTROL MODULE
(TACH) ODOMETER SELECT/RESET SWITCHDASH LIGHTS BRIGHTNESS CONTROLLER
GAUGE CONTROL MODULE
(SPEEDO)
PARKING BRAKE SWITCH
Test, page 8-9
Test, page 19-11
Test, page 11-340
Self-diagnostic Function, page 22-241
Input Test, page 22-271
Rewriting the ODO Data and Transferring Maintenance
Minder Data to a New Gauge
Control Module,
page 22-276
Replacement, page 22-277
Outside Air Temperature Indicator Calibration, page 22-279 Test/Replacement, page 22-278Test/Replacement, page 22-278
Input Test, page 22-274
Replacement, page 22-277
Test, page 19-11
08/08/21 14:28:53 61SNR030_220_0240
ProCarManuals.com
DYNOMITE -2009-

´µ

The Indicator Drive Circuit Check
Switch Input Check
The Beeper Drive Circuit Check
The LCD Segment Check
The Gauge Drive Circuit Check
22-242Gauges
Self-diagnostic Function (cont’d)
OFF ON
OFF ON
OFF ON
OFF ON
Gauge needles
Beeper
5sec.
Self-diagnostic
mode
SEL/RESET
SWITCH
When entering the self-diagnostic mode, the following indicators blink:
A/T gear position indicator, ABS indicator, brake system indicator, charging system indicator, cruise control indicator,
cruise main indicator, door indicator, DRL indicator, EPS indicator, fog light indicator , high beam indicator,
immobilizer indicator, lights-on indicator, low fuel indicator, low oil pressure indicator, low tire pressure indicator ,
maintenance minder indicator, malfunction indicator lamp (MIL), REV limit indicator (TYPE S model), seat belt
reminder indicator, security indicator, side airbag cutoff indicator, SRS indicator, TPMS indicator , trunk indicator,
VSA activation indicator , VSA indicator , and washer fluid level indicator.
1: ’07 TYPE S and ’08-09 models
2: ’08-09 models
3: TYPE S and ’08 Premium and ’09 models
At the initial stage of the self-diagnostic function, the beep sounds intermittently, the beeper sounds continuously
when any of the following switch inputs are switched from OFF to ON:
Cruise control main, dash lights brightness controller volume ( ), ( ) button, mph km/h switch, parking brake switch,
SEL/RESET switch, SET, RESUME, CANCEL switches, and VSA OFF switch . : ’07 TYPE S and ’08-09 models
When entering the self-diagnostic mode, the beeper sounds five times.
When entering the self-diagnostic mode, all the segments blink five times.
When entering the self-diagnostic mode, the tachometer needle sweeps from the minimum position to maximum
position, then returns to the minimum position.
NOTE:
After the beeper stops sounding and the gauge needle returns to the minimum position, pushing the SEL/RESET
switch starts the Beeper Drive Circuit Check (one beep) and the Gauge Drive Circuit Check again.
The check cannot be started again until the gauge needle returns to the minimum position.
If the needle fails to sweep, or the beeper does not sound, replace the gauge control module (tach).
3 2
2
11
The needle sweeps from the
minimum position to the
maximum position, then return
to the minimum position.
08/08/21 14:35:12 61SNR030_220_0244
ProCarManuals.com
DYNOMITE -2009-

Î
µ´µ
22-247
G5014
3 6
7
1
2
5
BLK
PUR
7
BLU 6
YEL 5
4
BRN
GRY
RED MAIN CIRCUIT
D
INDICATOR DRIVE CIRCUIT E
MAINTENANCE
MINDER
INDICATOR
(LED) SIDE
AIRBAG
CUTOFF
INDICATOR
(LED)
ILLUMI
() ILLUMI
()SEL/
RESET km/h
mph
LIGHTS
(LED)
GAUGE CONTROL
MODULE (TACH) No. 14 (7.5 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX) SEAT BELT
REMINDER
INDICATOR
(LED)
SRS
INDICATOR
(LED)
DASH LIGHTS BRIGHTNESS CONTROLLER and
ODOMETER SELECT/RESET SWITCH
WASHER
FLUID LEVEL
INDICATOR
(LED)
GAUGE CONTROL MODULE (TACH)
DRL
INDICATOR
(LED)
(cont’d)
08/08/21 14:35:14 61SNR030_220_0249
ProCarManuals.com
DYNOMITE -2009-

Î
µ´µ
22-254Gauges
Circuit Diagram - Gauge Control Module (Tach) (cont’d)
GAUGE CONTROL MODULE (TACH)
D
MAIN CIRCUIT
INDICATOR DRIVE CIRCUIT
DRL
INDICATOR
(LED)
DOOR
INDICATOR
(LED)TRUNK
INDICATOR
(LED)
MAINTENANCE
MINDER
INDICATOR
(LED) *
LOW TIRE
PRESSURE
INDICATOR
(LED) TPMS
INDICATOR
(LED)
G5014
3 6
7
1
2
5
BLK
PUR
7
BLU 6
YEL 5
4
BRN
GRY
RED ILLUMI
()
ILLUMI
()SEL/
RESETkm/h
mph
LIGHTS
(LED)
GAUGE CONTROL
MODULE (TACH) No. 14 (7.5 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
DASH LIGHTS BRIGHTNESS CONTROLLER and
ODOMETER SELECT/RESET SWITCH
C
08/08/21 14:35:16 61SNR030_220_0256
ProCarManuals.com
DYNOMITE -2009-