2006 ACURA CSX radio

Î
Î

Î

Unit Check (Quick Check)Display
Radio
23-305
ReturnReturn
ReturnSelect Check Units Display Radio Hard Key
Yaw Sensor DVD
GPS
ECU Info.
Rear Camera
PC Card Info Aircon
HFL
XM Display
OK
OK
Connection
Version
040423
Radio OK
Connection
OK
0.2dBuV
Electric Field Intensity
7150
CD Mech. Version
Some of the tests and screens that are displayed under
the Unit Check are different from the more detailed
checks listed in other areas of this service manual.
To start the test, select the item you want to check.
Display
Radio
GPS
ECUInfo.
 Rear Camera
 PC Card Info.
 Hard Key
 Yaw Sensor
DVD
 Aircon
HFL
XM This performs additional checks on the communication
bus between the navi CPU and the navigation display.
In addition, this test checks the internal electronic
functions
If the connection is NG, replace the navigation unit.
 Connection verifies internal communications.
 Version represents the software version for the display.
This diagnostic screen checks the internals of the radio
(AM and FM) and CD player. If NG, replace the
navigation unit.
(cont’d)
08/08/21 14:16:41 61SNR030_230_0308
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'#
)
´
µ
µ
µ
µ µ
µ
µ
µ
No picture is displayed
YES
NO
YES
NO YES
NO
YES
NO
23-338Navigation System
Symptom Troubleshooting
NAVIGATION UNIT CONNECTOR A (24P)
BBACKUP(WHT)
NAVIGATION UNIT CONNECTOR A (24P) ACC RADIO (PUR)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft code.
1. Check the No. 23 (10 A) fuse in the under-hood fuse/relay box and the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box, and reinstall the fuse if
it is OK.
Go to step 2.
Replace the fuse and recheck.
2. Turn the ignition switch to ON (II).
3. Operate the radio and listen to the audio.
Go to step 4.
Refer to audio system troubleshooting.
4. Turn the ignition switch to LOCK (0).
5. Remove the navigation unit (see page 23-355). 6. Measure the voltage between navigation unit
connector A (24P) terminal No. 24 and body ground.
Go to step 7.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
7. Turn the ignition switch to ON (II).
8. Measure the voltage between navigation unit connector A (24P) terminal No. 14 and body ground.
Go to step 9.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
Wire side of female terminals
Wire side of female terminals
IsthefuseOK? Can y ou hear t he aud i o? Is there battery voltage?
Is there battery voltage?
08/08/21 14:17:50 61SNR030_230_0341
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'#
)

µ
µ µ
µ
µ
µ
µ
µ
YES
NO Diagnostic Test: Monitor Check
YES
NO
YES
NO
YES
NO
Picture has lines/rolls/other issues or is an
odd color
23-33923-339
NAVIGATION UNIT CONNECTOR A (24P) RADIO GND (BLK)
NAVIGATION UNIT CONNECTOR C (8P) GND (BLK)
9. Measure the voltage between navigation unitconnector A (24P) terminal No. 12 and body ground,
and between navigation unit connector C (8P)
terminal No. 4 and body ground.
Replace the navigation unit (see page 23-355).
Repair open in the wire between the
navigation unit and body ground (G 504) (see page
22-30), (G505) (see page 22-32). NOTE:
 Check the vehicle battery condition frist.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the navigation screen settings for brightness, contrast, black level and the color screen for map
color and menu color.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft codes.
1. Check for electronic aftermarket accessories (possibly hidden) mounted near the navigation unit.
Disable the accessories, and recheck.
Go to step 2.
2. Turn the ignition switch to ON (II).
3. Start up the navigation picture.
Go to step 5.
Go to step 4.
4. Go into the Detail Information & Settings, select Monitor Check, and use RGB Color diagnostic
under Monitor Check (see page 23-302).
Go to step 5.
Replace the navigation unit (see page 23-355).
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is t her e l ess t han 0.1 V ? Ar e t her e any el ect r oni c accessor i es?
Is the picture scrolling horizontally (lef t to right orright to left)?
Ar e t he r ed , gr een, and bl ue col or ed ci r cl esshow n?
08/08/21 14:17:50 61SNR030_230_0342
ProCarManuals.com
DYNOMITE -2009-

µÎ

(#'#
)
µ
µ
µ
µ
YES
NO
YES
NO
System always comes up in in-line
diagnostic mode
23-34723-347
In Line Diag
123
456
789
0
Navi ECU
Display XXXXCorrect PIN
GPS Antenna
RR Camera RadioXM
HFL
A/C
Exit Diag
Start Diag
BACK
Delete Done
KA
2. Turn the ignition switch to ON (II).
3. Select the Self-Diagnosis mode.
4. Check for error code in the Error History.
Refer to the Hard Error Code
troubleshooting.
Go to step 5.
5. Substitute a known-good climate control unit. Reconnect all connectors, and retest.
Replace the original climate control unit
(see page 21-75).
Replace the navigation unit (see page 23-355). 1. When a navigation unit is powered up for the first
time at the factory, the factory diagnosis screen (In
Line Diag) appears. Normally the factory performs
the steps necessary to verify proper operation, and
terminate the factory diagnostic. Until the proper
confirmation sequence is performed, the screen
will appear every time the vehicle is started.
2. Follow the steps to prevent the screen from showingupinthefuture:
 Hold down the buttons (Menu, Map/Guide, and Cancel) for about 5 seconds. The Select
Diagnosis Items screen appears.
 Hold down the Map/Guide button for 5 10 seconds. A screen with a Complete button,
appears.
 Touch Complete, and then the Return button (the system may re-boot).
 Restart the vehicle, and confirm normal operation by completing the PDI of the
navigation system Service Bulletin.
Are there any Hard Error Code stored?
Does t he sy mpt om go aw ay ?
08/08/21 14:17:52 61SNR030_230_0350
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Navigation display stays on with ignition
switch in LOCK (0) Navigation cannot control audio system
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
23-34923-349
NOTE:
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code, then write down the audio presets.
 After troubleshooting, re-enter the anti-theft code, and re-initialize the navigation system, then enter the
audio presets.
 Check for aftermarket accessories that use the same power circuit. A feedback can cause this problem.
1. Remove the key from the ignition.
Go to step 2.
The system is OK at this time.
2. The vehicle may have been used as a demonstration vehicle at an event like an auto
show. In these events, power is often jumpered to
the navigation system so that the ignition key is not
needed in the vehicle. At the end of the show, the
jumper wire may not have been removed. Check
the navigation unit connector A (24P) for a non-
factory jumper wire in series with the factory cable.
Remove the jumper wire, and re-test. Return
the jumper wire to Tech Line.
Go to step 3.
3. Check if the audio unit works.
Troubleshoot the ACC circuit for a short to
power with another circuit.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic mode and use
Version (see page 23-316).
 Check for connectors for poor connections loose terminals.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
 Make sure that the correct navigation DVD color and version are installed.
 Inspect the navigation DVD for dirt or damage.
 Check any official Honda service website for more service information about the navigation system.
1. Make sure the anti-theft code for the navigation system is entered.
2. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-297).
Do the troubleshooting for the voice
guidance cannot be heard (see page 23-341).
Go to step 3.
3. Substitute a known-good navigation unit (see page 23-355), and recheck.
Replace the navigation unit (see page 23-355).
Do the audio system troubleshooting.
Does t he nav i gat i on scr een st ay on?
Is t her e a j umper w i r e?Does the audio unit work with the ignition switchoff? Is the Radio icon red?
Can t he nav i gat i on cont r ol aud i o?
08/08/21 14:17:52 61SNR030_230_0352
ProCarManuals.com
DYNOMITE -2009-

(#'#
)

Î
Î
(#'#
)
´µ
µ
µ
µ µ
µ
µ
µ
Navigation cannot control XM radio Navigation frequently asks for anti-theft
code and/or needs GPS initialization
YES
NO
YES
NO YES
NO
YES
NO
23-35023-350Navigation System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR A (24P)
BBACKUP(WHT)
NAVIGATION UNIT CONNECTOR A (24P) ACC RADIO (PUR)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
1. Start the vehicle.
2. Make sure the anti-theft code for the navigation system is entered.
3. Go into the Diagnostic mode, and use the System Links diagnosis (see page 23- 297).
Do the troubleshooting for the voice
guidance cannot be heard (see page 23-341).
Go to step 4.
4. Substitute a known-good navigation unit (see page 23-355).
Replace the navigation unit (see page 23-355).
Replace the XM receiver (see page 23-258). NOTE:
 This is often caused by a loss of battery power, a low or poor battery condition, or a poor ground.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
1. Measure the voltage between navigation unit connector A (24P) terminal No. 24 and body ground.
Go to step 2.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
2. Turn the ignition switch to ON (II).
3. Measure the voltage between navigation unit connector A (24P) terminal No. 14 and body ground.
Go to step 4.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
Wire side of female terminals
Wire side of female terminals
Is the X M icon red? Can t he nav i gat i on sy st em cont r ol X M r ad i o? Is there battery voltage?
Is there battery voltage?
08/08/21 14:17:52 61SNR030_230_0353
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'#
)
µ
µ µ
µ
YES
NO YES
NO
OPEN/CLOSE function of the display does
not work
23-35123-351
NAVIGATION UNIT CONNECTOR A (24P)
RADIO GND (BLK)
NAVIGATION UNIT CONNECTOR C (8P) GND (BLK)
4. Measure the voltage between navigation unitconnector A (24P) terminal No. 12 and body ground,
and between navigation unit connector C (8P)
terminal No. 4 and body ground.
Replace the navigation unit (see page 23-355).
Repair open in the wire between the
navigation unit and body ground (G 504, G505).NOTE:
 Check the vehicle battery condition first.
 If the display’s Open/Close button does not work, you must manually open the display to obtain the client’s
navigation DVD, audio CD, and PC card (see page
23-269).
1. Press the OPEN/CLOSE button.
The system is OK at this time.
Replace the navigation unit (see page 23-355).
Wire side of female terminals
Wire side of female terminals
Is t her e l ess t han 0.1 V ? Does t he d i spl ay open and / or cl ose nor mal l y ?
08/08/21 14:17:53 61SNR030_230_0354
ProCarManuals.com
DYNOMITE -2009-


(#'
")
Pre-operation Check Set-up After Replacing Front Passenger’s Seat
Component(s)
24-28SRS
ODS Unit Operation Check
A
Check the ODS operation after any of these actions.
 Replacement of front passenger’s seat component(s) (except ODS unit and/or weight sensors)
 After a vehicle collision
 SRS unit replacement
 Make sure all the components of the front passenger’s seat are correctly installed.
 Position the front passenger’s seat to the rearmost position.
 Adjust the seat-back to the forwardmost position.
 Do not move the seat from this position.
 Make sure nothing is on or under the front passenger’s seat.
 Make sure there is nothing in the front passenger’s seat-back pocket.
 Keep the windows and moonroof closed.
 Do all calibration procedures, except test-driving, in the service bay.
 Make sure the vehicle is on level gr ound.
 Turn the heater and the A/C off.
 Do not touch the front passenger’s seat during the calibration, unless you are prompted to or until you
have completed the operation check.
 Do not expose the front passenger’s seat to sudden temperature changes.
 Make sure all aftermarket devices such as amplifiers, fluorescent lights, air purifies, CB or HAM radios, etc.
are turned off. 1. Make sure the ignition switch is in LOCK (0).
2. Connect the HDS to the data link connector (DLC)
(A).
3. Turn the ignition switch to ON (II).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
5. Drive the vehicle, accelerate to 20 mph (36 km/h), then stop on level ground.
6. From the HDS Main Menu, select SRS, then Inspection. In the HDS Inspection Menu, select
SEAT OUTPUT CHK and follow the prompts until
the ODS unit operation check is complete.
08/08/21 13:54:23 61SNR030_240_0028
ProCarManuals.com
DYNOMITE -2009-