2006 ACURA CSX ignition

(#'
!)
22-287
Resetting the Moonroof Control Unit
Resetting the moonroof is required when any of the following have occurred: The moonroof was moved manually while the battery was dead or disconnected.
 The moonroof motor was replaced with a new one.
 Any of components related to the moonroof were replaced. – Wind deflector
– Moonroof glass
– Moonroof seal
– Moonroof glass bracket
– Moonroof cables, etc.
To reset the moonroof control unit, do these steps: 1. Close the driver’s door, and keep it closed until the procedure is complete.
2. Turn the ignition switch to LOCK (0).
3. Press and hold the tilt switch, and turn the ignition switch to ON (II).
4. Release the tilt switch, and turn the ignition switch to LOCK (0).
5. Repeat steps 3 and 4 four times.
6. Press and hold the moonroof open switch for 3 additional seconds after the moonroof is fully opened.
7. Press and hold the moonroof close switch for 3 additional seconds after the moonroof is fully closed (tilted).
8. Confirm that the moonroof control unit is reset by using the moonroof AUTO OPEN and AUTO CLOSE function.
08/08/21 14:36:04 61SNR030_220_0289
ProCarManuals.com
DYNOMITE -2009-


(#') ’06-07 models
22-288Moonroof
Circuit Diagram
No. 24
(20 A)
IGNITION SWITCH
BATIG1
WHT
BLU
No. 2 (IG) (50 A)
BATTERY
No. 1 (BAT) (100 A)
(20 A)
D2
G21
E23
K3
K7
YEL
WHT
(CLOSE)
(OPEN) PUR
PUR PUR
LT GRN PUR
5
AUTO
AUTO
MOONROOF CONTROL UNIT
6
10OPEN CLOSE
HALL SENSOR
ECM/PCM
4
BLU GRN
No. 4 (P/W) (40 A)
1
10 7
8
9
7
LT BLU
CPU
MOONROOF SWITCH
BLU
G503 BLK
GRY
5 6
2
9 LT GRN
4
GRN LIGHT
(LED)
TILT
MOTOR
CLOSE
OPEN No. 32
UNDER-HOOD FUSE/RELAY BOX
RIGHT REAR
WINDOW MOTOR
No. 14 (7.5 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
DASH LIGHTS
BRIGHTNESS
CONTROLLER UNDER-DASH
FUSE/RELAY BOX
IG1 HOT in ON (II)
and START (III)
H1
K2
08/08/21 14:36:04 61SNR030_220_0290
ProCarManuals.com
DYNOMITE -2009-


(#'
)
22-290Moonroof
Moonroof Control Unit Input Test
A
B
WHT
GRN
PUR LT BLU
LT GRN
YELBLK
BLU
NOTE: If the moonroof works OK manually, but will not work in AUTO, or r everses frequently (obstacle detection), do
the moonroof calibration (see page 22- 287) before proceeding with the input test.
1. Turn the ignition switch to LOCK (0).
2. Remove the headliner (see page 20-84).
3. Disconnect the 10P connector (A) from the moonroof control unit (B).
4. Inspect the connector and socket terminals to be sure they are all making good contact.  If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
 IftheterminalslookOK,gotostep5.
Wire side of
female terminals
08/08/21 14:36:05 61SNR030_220_0292
ProCarManuals.com
DYNOMITE -2009-

Cavity Wire Test conditionTest: Desired result Possible cause if desired result is
not obtained
22-291
5. Reconnect the connector to the moonroof control unit, and do these input tests at the following connector.
 If any test indicates a problem, find and correct the cause, then recheck the system.
 If all the input tests prove OK, go to step 6.


























1 GRN Under all
conditions Measure the voltage to ground:
There should be battery voltage. Blown No. 24 (20 A) fuse in the
under-dash fuse/relay box
An open in the wire
5 PUR Ignition switch ON (II) Measure the voltage to ground:
There should be battery voltage. Blown No. 32 (20 A) fuse in the
under-dash fuse/relay box
An open in the wire
10 BLK Under all conditions Measure the voltage to ground:
There should be less than 0.5 V. Poor ground (G503)
An open in the wire
6 WHT Moonroof switch in AUTO OPEN or
AUTO CLOSE
position Measure the voltage to ground:
There should be battery voltage.
Faulty moonroof switch
Blown No. 32 (20 A) fuse in the
under-dash fuse/relay box
Blown No. 23 (10 A) fuse in the
under-hood fuse/relay box
Faulty under-dash fuse/relay
box
An open in the wire
7 LT GRN Moonroof switch in TILT position Measure the voltage to ground:
There should be battery voltage. Faulty moonroof switch
Blown No. 32 (20 A) fuse in the
under-dash fuse/relay box
Blown No. 23 (10 A) fuse in the
under-hood fuse/relay box
Faulty under-dash fuse/relay
box
An open in the wire
8 YEL Moonroof switch in CLOSE position Measure the voltage to ground:
There should be battery voltage. Faulty moonroof switch
Blown No. 32 (20 A) fuse in the
under-dash fuse/relay box
Blown No. 23 (10 A) fuse in the
under-hood fuse/relay box
Faulty under-dash fuse/relay
box
An open in the wire
9 LT BLU Moonroof switch in OPEN position Measure the voltage to ground:
There should be battery voltage. Faulty moonroof switch
Blown No. 32 (20 A) fuse in the
under-dash fuse/relay box
Blown No. 23 (10 A) fuse in the
under-hood fuse/relay box
Faulty under-dash fuse/relay
box
An open in the wire
1: ’06-07 models
2: ’08-09 models
(cont’d)
12
1 2
1 2
1 2
08/08/21 14:36:05 61SNR030_220_0293
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
µ
µ
22-295
Circuit Diagram
(15 A) No. 29
BLU
G503BLK
PUR
(80 A) *1
(60 A) *2
BLK
G503
G601 YEL
BLK
1
2 PUR
GRN No. 28
(15 A) No. 2
(OPTION)
No.1(BAT)(100A) No.2(IG)(50A)
BATTERY UNDERHOOD FUSE/RELAY BOX
PUR2 1
G502 BLK
WHT (7.5 A) No. 35
RED ACC
BAT WHT
IGNITION
SWITCH
ACC HOT in ACC (I)
and ON (II)
UNDER-DASH
FUSE/RELAY
BOX
CONSOLE
ACCESSORY
POWER SOCKET
RELAY FRONT
ACCESSORY
POWER
SOCKET
CONSOLE
ACCESSORY
POWER
SOCKET FRONT
ACCESSORY
POWER SOCKET
RELAY
H1
G1
G19 C2
E35 K8 Q14
2 4
1 3 24
1
3
WHT*1
RED*2 *1: ’06 07 models
*2: ’08 09 models
MICU
08/08/21 14:36:07 61SNR030_220_0297
ProCarManuals.com
DYNOMITE -2009-




(#'


)
22-296 Accessory Power Sockets
Front Accessory Power Socket Test/Replacement
BLK
WHT
A B
A
A
NOTE: If both of the front and console accessory power
sockets do not work, check the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box. 1. Remove the center panel.  With audio:– ’06-08 models (see page 23-80)
– ’09 model (see page 23-256)
 With navigation: – ’06-08 models (see page 23-155)
– ’09 model (see page 23-355)
2. Disconnect the 2P connector (A) from the front accessory power socket (B).
3. Inspect the connector terminals to be sure they are all making good contact.
 If the terminals are bent, loose, or corroded, repair them as necessary and recheck the system.
 IftheterminalslookOK,gotostep4.
4. Turn the ignition switch to ACC (I).
5. Measure the voltage between front accessory power socket 2P connector terminal No. 1 and body
ground. There should be battery voltage.
 If there is battery voltage, go to step 6.
 If there is no voltage, check for: – Blown No. 29 (15 A) fuse in the under-dash fuse/relay box.
– Faulty front accessory power socket relay.
– Poor ground (G 503).
– Anopeninthewire. 6. Check for continuity between front accessory
power socket 2P connector terminal No. 2 and body
ground. There should be continuity.
 If there is continuity, replace the power socket; go to step 7.
 If there is no continuity, check for: – Poor ground (G 502).
– Anopeninthewire.
7. Remove the socket (A).
8. Remove the housing (A) from the panel.
9. Install the front accessory power socket in the reverse order of removal.
Wire side of
female terminals
08/08/21 14:36:08 61SNR030_220_0298
ProCarManuals.com
DYNOMITE -2009-

Î


(#'



)
22-297
Console Accessory Power Socket Test/Replacement
BLK
YEL
A
B
A
A
NOTE: If both of the front and console accessory power
sockets do not work, check the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box. 1. Remove the center console (see page 20-95).
2. Disconnect the 2P connector (A) from the console accessory power socket (B).
3. Inspect the connector terminals to be sure they are all making good contact.
 If the terminals are bent, loose, or corroded, repair them as necessary and recheck the system.
 IftheterminalslookOK,gotostep4.
4. Turn the ignition switch to ACC (I), and measure the voltage between console accessory power socket
2P connector terminal No. 1 and body ground.
There should be battery voltage.
 If there is battery voltage, go to step 5.
 If there is no voltage, check for: – Blown No. 28 (15 A) fuse in the under-dash fuse/relay box.
– Faulty console accessory power socket relay.
– Poor ground (G 503).
– Anopeninthewire. 5. Check for continuity between console accessory
power socket 2P connector terminal No. 2 and body
ground. There should be continuity.
 If there is continuity, replace the power socket; go to step 6.
 If there is no continuity, check for: – Poor ground (G 601).
– Anopeninthewire.
6. Remove the socket (A).
7. Remove the housing (A) from the panel.
8. Install the console accessory power socket in the reverse order of removal.
Wire side of
female terminals
08/08/21 14:36:08 61SNR030_220_0299
ProCarManuals.com
DYNOMITE -2009-

Î(#'"
)
22-300Seat Heaters
Circuit Diagram
Q16
IG2 HOT in ON (II) G19 C3
M5
LT GRN
GRN/RED LT GRN
OFF 1
2
GRN/RED LT GRN
6
5
3
BLU
BLK HIGH
LOW
4
LT BLU GRY
LT GRN
DRIVER’S SEAT HEATER
3
YEL
BLK
BLK BLK CUSHION
1
2
2
1
BACK
BR TH DRIVER’S SEAT HEATER RELAY BOX
BLU/YEL
BRN
ORN
BLK RED
RED
RED No. 5 (15 A)
No.36(HAC)(10A)
G601
G601 IGNITION SWITCH
IG2
BAT
ORN
WHT
UNDER-HOOD FUSE/RELAY BOX
No. 2 (IG) (50 A)
No. 1 (BAT) (100 A)
BATTERY UNDER-DASH FUSE/RELAY BOX
SEAT
HEATER
RELAY
(HIGH) SEAT
HEATER
RELAY
(LOW)
No.14(7.5A)FUSE
(UNDER-DASH
FUSE/RELAY BOX)
DASH LIGHTS
BRIGHTNESS
CONTROLLER LIGHT
(LED)
INDICATOR
(LED)DRIVER’S SEAT
HEATER SWITCH
INDICATOR
(LED)
H1
G1
1 4
2 343
1 5
2
No. 2 (OP) (80 A) *1
(60 A) *2 WHT*1
RED*2
BLU
BLU*1
ORN*2 GRN*1
BRN*2 MICU
08/08/21 14:36:48 61SNR030_220_0302
ProCarManuals.com
DYNOMITE -2009-