2006.5 Citroen C4 DAG Owner's Manual

1
5
4
23
6
IN BRIEF
I
20
F R O N T S E A T S
86

1
2
5
4
3
6
IN BRIEF
I
21
F R O N T S E A T S
Manual adjustments Head restraint
To raise, pull upwards. To lower, press on the unlocking but ton and on the head restraint. The
adjustment is correct when the upper edge of the restraint is l evel with the top of your head. The
head restraint is also angle-adjustable.
To remove, press on the unlocking button and pull upwards.
Note: Never drive the vehicle without the head restraints fitted.
Reach
Lift the control bar and adjust to the desired position.
Lumbar supports
Turn the control and adjust to the desired position.
Driver’s seat height
Raise or lower the control the number of times required to obt ain the desired position.
Backrest angle
Use the control A to adjust the backrest angle.
It is possible to recline the backrest to an angle of 45° by tilting it until it locks; press the control to
unlock.
Access to the rear seats
To access or exit the rear seat positions, tilt the control 6 towards the front to fold the front seat
back-rest and slide the front seat forwards.
Afterwards the front seat will revert to its initial position.
Make sure that the seat is securely locked in place.
Note: This control holds the seat belt in position (see preceding page).

12
IN BRIEF
I
22 F R O N T S E A T S
Heated seats
The front seats can be heated
independently. Use the controls
placed on the sides of the seats,
turning them to select one of three
heating levels:
0: Stop.
1: Gentle heat.
2: Medium heat.
3: Strong heat.
The seat temperature will adjust
accordingly.
Note: The heated seats will only
operate when the engine is run-
ning.
Note: The seats can still be moved on a temporary basis:
- when opening one of the front doors.
- after switching off the ignition. Electrically operated
adjustments

Adjustment of seat height,
angle and reach
 Adjustment of backrest
angle and lumbar support
Raise or lower the front of control
1 to make the front of the seat
cushion higher or lower.
Raise or lower the rear of control 1 to make the seat higher or
lower.
Action control 1 to the front or to the rear to move the seat for-
ward or back.
Push the top of control 2 forward or back to adjust the backrest
angle.
Raise or lower control 2 to increase or decrease the lumbar sup-
port.

1
2
M
IN BRIEF
I
23
F R O N T S E A T S
Memorisation of driving positions
You have the possibility to memorise two driving positions, via the buttons M/1 and M/2.
Memorisation using the buttons
To memorise, using the buttons located on the side of the se at:
- turn the ignition key to the drive position (2nd notch),
- adjust your seat and your exterior rear view mirrors,
- press on button M then immediately on button 1 «first driving position» or on button 2 «second driving posi-
tion».
The memorisation is recognised by an audible signal. Memorising o f a new position cancels the previous one.
Recall of a memorised driving position
Vehicle stopped (ignition on or engine running)
- Press briefly on button 1 or 2 to recall the corresponding memorised position.
Note: after five consecutive recalls of a memorised position, this function will b e deactivated until the engine is
started.
Vehicle moving
- Keep button 1 or 2 pressed to recall the corresponding memorised position.

21
IN BRIEF
I
24 Automatic photochromic
interior rear view mirror
This provides an automatic and
progressive changing between
day use and night use.
To avoid causing dazzle, the mirror
automatically becomes darker as
a function of the intensity of light
coming from the rear. It becomes
lighter as soon as brightness
diminishes, thus ensuring optimal
vision.
To operate
Switch on the ignition and press
control
1.
- Warning lamp 2 on: automatic
mode.
- Warning lamp 2 off: automatic
mode stopped. The mirror
remains in its lightest definition.
Note: for optimal vision, the mir-
ror lightens automatically when
reverse gear is engaged.
Manual interior mirror
The lever on the lower edge ena-
bles you to place the rear view
mirror in either of two positions:
Day position:
the lever is not vis-
ible.
Night position (antidazzle): the
lever is visible. Permit holder
The athermic windscreen incorpo-
rates a zone located either side of
the rear view mirror base, to allow
the reading of access cards (e.g.
motorway toll passes).
I N T E R I O R R E A R V I E W M I R R O R

21
IN BRIEF
I
25
D O O R M I R R O R S
Adjustment of rear view
mirrors
Functions with ignition switched
on.
From the driver’s position,
select the rear view mirror via
the control 1, then adjust in the
four directions by moving the
control 2.
Deicing of rear view mirrors is
coupled with electric demisting of
the rear screen. Fold-back of door mirrors
When the vehicle is parked, the
door mirrors can be folded back
either manually or electrically.
Electric fold-back
From the central position, one
press towards the rear on control
1
folds the rear view mirrors back.
To return them to the initial posi-
tion, press again on the control
towards the rear.
Automatic fold-back
Automatic fold-back operates
when you lock the doors with the
remote control.
The opposite movement applies
when you unlock the doors, except
if you operated fold-back before
switching off the ignition.
Note: Automatic fold-back of the
rear view mirrors can be deac-
tivated. Consult your CITROËN
dealer. Adjustment of the indexed
positions for the passenger’s
and driver’s rear view mirrors
With the engine running:
- Select the rear view mirror using
control 1.
- Engage reverse gear, the mirror glass automatically positions
itself to improve your vision of
the pavement.
- If necessary, adjust the mirror to your preference using the elec-
tric control 2.
Deactivation of the rear view
mirror indexing function
To deactivate the function, move
control 1 to the central position.

IN BRIEF
I
26 Electric operation
The driver uses the controls
located on the door to operate the
vehicle’s electric windows.
Note:
the electric windows can
also be operated for a limited
time after the ignition has been
switched off (including after the
front doors have been opened).
Sequential control
An action on the control to the first
notch causes a window move-
ment which stops as soon as the
control is released. An action on
the control to the second notch
causes the window to close or
open fully, a further press on the
control stops the movement.
ALWAYS PAY ATTENTION TO WHERE CHILDREN ARE WHEN OPENING OR CLOSING WINDOWS.
- Always remove the ignition key when leaving the vehicle, even for short
periods.
- If the driver is operating the passenger’s electric window con trol, the driver
should ensure that no passenger is obstructing the window from closing.
- The driver should check that the electric windows are used prope rly by the
passengers.
- Should there be any risk of a person becoming trapped by a win dow clos-
ing, you should immediately reverse the window movement. To do this,
reverse the position of the control concerned.
This prevents the rear windows from being operated, and the re ar
doors from being opened, from the rear seat positions.
It is activated by means of a press on control A located on the
electric windows control panel. The warning lamp in the inst rument
panel lights up for approx. 10 seconds.
Each time the ignition is switched on, the warning lamp comes on for
approx. 10 seconds.
Opening of the doors from the outside and operation of th e rear electric
windows remain possible from the front of the vehicle.
Anti-pinch device
An anti-pinch device stops the window from rising. If it meets a
n obstacle,
it goes back down.
After a battery disconnection or in the event of a malfunctio n, you
have to re-initialise the anti-pinch function:
- Lower the window fully using the control, then close. It will rise only a few
centimetres.
- Press repeatedly on the control until the window is fully clo sed.
Warning: During this operation, the anti-pinch protection does not work.
W I N D O W S
Child safety

1
34A
2
IN BRIEF
I
30 This driving assistance function
allows you to drive at the speed
of your choce without the need to
action the accelerator. It is avail-
able at speeds above 40 km/h
(25 mph), in the higher gears only.
Control
A for cruise control is
located below the lighting/signal-
ling stalk.
Note: Information relating to the
cruise control is displayed in
zone A of the instrument panel.
To select the function
Turn control 1 to position “REG”.
To select a cruising speed
At the time you select the func-
tion via the control 1, there is no
cruise speed previously memo-
rised: Note:
you can use successive
presses to modify the cruise
speed in steps of 1 km/h and a
continuous press to jump in steps
of 5 km/h.
Accelerate to the desired speed,
then press button
2 or button
4 . The cruise speed will then
be memorised and displayed in
zone A on the instrument panel.
You can then release the accel-
erator pedal. The vehicle will
automatically keep to that chosen
speed.
Note: The vehicle speed may vary
slightly from that memorised.
C R U I S E C O N T R O L
Adjustment of the memorised
speed while cruise control is in
operation
To adjust the memorised speed,
displayed in zone A, press on:
- button 4 to increase the speed,
- button 2 to decrease the speed. To exceed the cruise speed
temporarily
While cruise control is in use, it is
always possible to go above the
cruise speed simply by pressing
the accelerator pedal (for exam-
ple to overtake another vehicle).
The speed displayed in zone
A
flashes.
You have only to release the acce-
lator pedal to return to your cruise
speed.
Note: if during cruise control the
system cannot keep to the cruise
speed (e.g. on a steep descent),
then the speed flashes. If neces-
sary, brake to curb your speed.