2005 TOYOTA AVENSIS recognition code

Room Lamp Output
Normal wave of UNLOCK switchUnmatching recognition code
No diagnosis outputs ON
OFF
T1: 0.25 sec. Wave is being received ON
OFF
OFF T1 T1 T1 T2 Normal wave of LOCK switch
ON
OFF
T1 T2
Normal wave of luggage door (back door)
unlock switch
ON
OFF
T2
T2
T2: 0.5 sec. Room Lamp Output
Room Lamp OutputRoom Lamp Output
Room Lamp Output
± DIAGNOSTICSWIRELESS DOOR LOCK CONTROL SYSTEM
05±1579
AVENSIS REPAIR MANUAL (RM1018E)
6 CHECK BY SELF±DIAGNOSTIC MODE
(a) Inspect the diagnosis outputs when the door control transmitter switch is held down (The diagnosis
outputs can be checked with the outputs of the room lamp).
HINT:

In the case of a reception of the normal wave of the door LOCK, UNLOCK switch or luggage door (back
door) unlock switch (room lamp blinking), go to step A.

In the case of an unmatching recognition code (room lamp ON), go to step B.

In the case of no diagnosis outputs (room lamp OFF), go to step C.
A REPLACE INSTRUMENT PANEL JUNCTION
BLOCK ASSY
C Go to step 8
B

05±1580
± DIAGNOSTICSWIRELESS DOOR LOCK CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
7 REGISTER RECOGNITION CODE
(a) Check that the system can switch to rewrite mode or add mode and whether a recognition code can
be registered.
NG Go to step 16
OK
NORMAL (CARRY OUT INSPECTION OF FUNCTIONS)
8 SIMPLY CHECK TRANSMITTER BATTERY
(a) After replacing the transmitter battery with a new or normal one, check that the doors can lock and
unlock using the transmitter LOCK/UNLOCK switch.
NG REPLACE TRANSMITTER SUB±ASSY MODULE
SET DOOR CONTROL
OK
REPLACE TRANSMITTER BATTERY
9 CHECK RESPONSE OF DOOR CONTROL RECEIVER
(a) When a new or normal door control transmitter switch for the same type vehicle is held down, check
that a diagnosis of unmatching recognition code is output.
NG Go to step 13
OK
REPLACE TRANSMITTER SUB±ASSY MODULE SET DOOR CONTROL
10 CONFIRM INPUT METHOD OF SELF±DIAGNOSTIC MODE
(a) When the method for switching the system to self±diagnostic mode works, proceed to A.
(b) When the method for switching the system to self±diagnostic mode does not work, proceed to B.
B Go to step 6
A

730EY±02
± THEFT DETERRENT & DOOR LOCKTRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL73±21
AVENSIS REPAIR MANUAL (RM1018E)
REGISTRATION
1. REGISTER RECOGNITION CODE
HINT:

Register the recognition code when replacing the door control transmitter or the door control receiverr.

The add mode is used to register new recognition codes while still retaining codes already registered.
This mode is used when a new transmitter is added. If the number of registered codes exceeds 4, the
previously registered codes will be erased in order, starting from the first registered code.

The rewrite mode is used to erase all the previously registered recognition codes in order to register
new recognition codes. This mode is used when the transmitter or the door control receiver is ex-
changed for a new one.

The confirmation mode is used to confirm how many recognition codes have already been registered
before an additional registration of a recognition codes.

The all clear mode is used to erase all the registered codes and disables the wireless door lock func-
tion. This mode is used when the transmitter is lost.

All the following registration procedures must be performed in order continuously.

Within 5 sec.
Within 40 sec.
Continued on next page 1.
2.
3.
4.
5.
6.Insert key into ignition key cylinder, then pull it out.
Close and open driver side door twice.
Close and open driver side door twice.
Insert key into ignition key cylinder and close all doors.
START
Insert key into ignition key cylinder, then pull it out.
Insert key into ignition key cylinder, then pull it out.
Flow Chart of Recognition Code Registration
Within 40 sec.
Within 40 sec.Make sure that the following conditions are met.


No key in ignition key cylinder.

Driver side door is open (Other doors are closed).


Driver side door is unlocked. 73±22
± THEFT DETERRENT & DOOR LOCKTRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL
AVENSIS REPAIR MANUAL (RM1018E)

Continued from previous page
Integration relay automatically performs power door LOCK±UNLOCK operation to inform
which mode has been selected.
Response to selected mode (Power door lock operation):
UNLOCKLOCK
LOCK±UNLOCK operation: 1 time Add Mode
Rewrite Mode
Confirmation Mode
All Clear Mode
T1T1: Approx. 1 sec.
T1 T1
T2
T2
T1 T1
LOCK±UNLOCK operation: 2 times
LOCK±UNLOCK operation: The number of registered codes (1 ± 5 times)
LOCK±UNLOCK operation: 5 timesUNLOCKLOCK
UNLOCKLOCK
UNLOCKLOCK
Continued on next page
Registration procedures are completed.
HINT:

In the confirmation mode, when LOCK±UNLOCK operation is performed twice, the
number of registered recognition codes is 2.

In the confirmation mode, when 0 codes are registered, LOCK±UNLOCK operation
is automatically performed 5 times.T2: Approx. 2 sec.
Confirmation Mode and
All Clear ModeAdd Mode or
Rewrite Mode Within
3 sec.
Within
40 sec.
1st time 2nd time
73±24± THEFT DETERRENT & DOOR LOCKTRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL
AVENSIS REPAIR MANUAL (RM1018E)

Continued from previous page
Press either LOCK or UNLOCK switch on transmitter once. 9.
Within 40 sec.
Proceed to flow chart to finish
registration.
Press the same switch again.
LOCK±UNLOCK Occurs Once
Registration of recognition code has
been completed. Response to registration completion:
T1: Approx. 1 sec. LOCK±UNLOCK Occurs Twice
Registration of recognition code has failed. 10.
LOCK
UNLOCK
T1
LOCK
UNLOCKT1 T1
Within
40 sec.
If other transmitter is to be registered. Within
3 sec.
Registration of recognition codes (add mode and rewrite mode) is completed.
Integration relay automatically performs power door LOCK±UNLOCK operation to show
whether registration has been completed correctly or not.
HINT:
4 recognition codes can be registered
at once. HINT:
If LOCK±UNLOCK operation is performed twice, registration of recognition code has
failed. Perform registration procedures by beginning once again.
Within
3 sec.

Open a door.

Insert key into ignition key cylinder. Perform either of the following.
± THEFT DETERRENT & DOOR LOCKTRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL73±25
AVENSIS REPAIR MANUAL (RM1018E)

730EV±02
±
THEFT DETERRENT & DOOR LOCK WIRELESS DOOR LOCK CONTROL SYSTEM
73±15
AVENSIS REPAIR MANUAL (RM1018E)
ON±VEHICLE INSPECTION
1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
HINT:

The switch described in this text is a switch for transmitting signals (LO\
CK switch, UNLOCK switch and
luggage door (back door) unlock switch) which is built in the door control t\
ransmitter.

All the functions listed below must be checked in comparison with the re\
mote control operational area.
(a)Put the vehicle under the conditions that allow the wireless control fun\
ction to be operated (See PRE-
CAUTION on page 73±14).
(b) Check the basic function. (1) Check whether the LED of the transmitter lights up 3 times when each switch i\
s pressed 3 times.
HINT:
If the LED does not light up when the switch has been pressed 3 times or more, it may have a dead bat\
tery.
(2) Check that all the doors including the luggage door (back door) lock when t\
he LOCK switch ispressed (However, this will not happen when any door is open).
(3) w/ Double locking system: Check that the double locking system is set when the LOCK switch is pressed within 5 seconds
after the above step (However, the double locking system is not applicable to the luggage door
(back door)).
CAUTION:
Never activate the double locking system when there are people in the vehicle, because all the doors
cannot be opened from inside the vehicle with the system on. If you lock\
the doors by accident, push
UNLOCK switch of the door control transmitter. (4) Check that all the doors including the luggage door (back door) unlock when\
the UNLOCK switchis pressed. Also, check that the double locking system is canceled at th\
e same time.
(5) Check that the luggage door (back door) unlocks when the luggage door (bac\
k door) unlock
switch is pressed.
HINT:
The UNLOCK switch and luggage door (back door) unlock switch can unlock t\
he doors even when any door
is open.
(c) Check the chattering prevention function. (1) Check that the corresponding operation occurs only once, and not repeated continuously whilethe switch is held down. However, when the switch is operated repeatedly at 1 second intervals,
check that the corresponding operation is carried out.
(d) Check the automatic locking function. (1) Check that all the doors including the luggage door (back door) lock automatically as long asnone of them have been opened or locked within approx. 30 seconds after they\
are unlocked
by pressing the switch.
(2) Check that the automatic locking function does not operate when any door incl\
uding the luggage
door (back door) has been opened or all of them have been locked within ap\
prox. 30 seconds
after they are unlocked by pressing the switch.
(e) Check the switch operation fail±safe function. (1) Check that the doors can not be locked by the switch while the key is in the \
ignition key cylinder.
However, this does not apply when the system is in the recognition code registra\
tion mode.
(f) Check the repeat function. (1) Check that all the doors attempt to automatically lock once again 1 second af\
ter the LOCK switchhas been pressed while the movement of the driver side door control knob, which is in the un-
locked state, is being restricted.