2005 SUZUKI MARUTI warning

Downloaded from www.Manualslib.com manuals search engine 12383K
EMERGENCY SERVICE
10-2
2) Set the parking brake firmly and shift
into “R” (Reverse).
3) Turn on the hazard warning flasher if
your vehicle is near traffic.
4) Get down all the passengers.
5) Block the front and rear of the wheel
diagonally opposite of the wheel being
lifted.
6) Place the spare wheel near the wheel
being lifted as shown in the illustration
in case that the jack slips.
83K-08-00683K-08-007
CAUTION
Never jack up the vehicle with pas-
sengers inside the vehicle. 7) Position the jack vertically and raise the jack
by turning the jack handle clockwise until the
jack head recess fits the jacking point.
8) Continue to raise the jack slowly and
smoothly until the tyre clears the ground. Do
not raise the vehicle more than necessary.
w ww w
w WARNING
Use the jack only to change wheels
on level, hard ground.
Never jack up the vehicle on an
inclined surface.
Never raise the vehicle with the jack
in a location other than the specified
jacking point (shown in the illustration)
near the wheel to be changed.
Especially, do not raise the vehiclewith a jack at a part of the torsion
beam which is located under the
vehicle body, between rear wheels.
Make sure that the jack is raised at
least 51 mm (2 inches) before it
contacts the suspension arm boss.
Use of the jack when it is within 51
mm (2 inches) of being fully collapsed
may result in failure of the jack.
Never get under the vehicle when it
is supported by the jack.
Never run the engine when the
vehicle is supported by the jack and
never allow passengers to remain in
the vehicle.
V VV V
V
w ww w
w WARNING
V VV V
V
Changing WheelsTo change a wheel, use the following pro-
cedure:
1) Clear all passengers and luggage from
the vehicle.NOTE:
The jack and tools are located under the
spare wheel.2) Remove the jack, tools and spare wheel
from the vehicle.
3) Loosen, but do not remove the wheel
nuts.
4) Jack up the vehicle.
5) Remove the wheel nuts and wheel.
6) Before installing the new wheel, clean
any mud or dirt off from the surface of
83K-08-008

Downloaded from www.Manualslib.com manuals search engine 12483K
EMERGENCY SERVICE
10-3
the wheel and hub with a clean cloth.
Clean the hub carefully; it may be hot
from driving.
7) Install the new wheel and replace the
wheel nuts with their cone shaped end
facing the wheel. Tighten each nut
snugly by hand until the wheel is
securely seated on the hub.
83K-08-009
Tightening torque for wheel nut
85 Nm (8.5 kg-m, 61.5 lb-ft)
8) Lower the jack and fully tighten the nuts
in a crisscross fashion with a wrench as
shown in the illustration.
w ww w
w WARNING
Use Maruti genuine wheel nuts and
tighten them to the specified torque
as soon as possible after changing
V VV V
V
wheels. Incorrect wheel nuts or
improperly tightened wheel nuts may
come loose or fall off, which can
result in an accident. If you do not
have a torque wrench, have the wheel
nut torque checked by a MARUTI
SUZUKI authorized dealer.
w ww w
w WARNING
V VV V
V
Jump Starting Instructions
w ww w
w WARNING
Never attempt to jump start your
vehicle if the battery appears to be
frozen. Batteries in this condition
may explode or rupture if jump
starting is attempted.
When making jump lead connec-
tions, be certain that your hands
and the jump leads remain clear
from pulleys, belts, or fans.
Batteries produce flammable
hydrogen gas. Keep flames and
sparks away from the battery or an
explosion may occur. Never smoke
when working in the vicinity of the
battery.
If the booster battery you use for
jump starting is installed in another
vehicle, make sure the two vehicles
are not touching each other.
V VV V
V
w ww w
w WARNING
V VV V
V
CAUTION
Your vehicle should not be started by
pushing or towing. This starting
method could result in permanent
damage to the catalytic converter and
high pressure fuel pump (diesel). Use
jump leads to start a vehicle with a
weak or flat battery. If your battery discharges repeat-
edly, for no apparent reason, have
your vehicle inspected by a MARUTI
SUZUKI authorized dealer.
To avoid harm to yourself or dam-
age to your vehicle or battery, fol-
low the jump starting instructions
below precisely and in order.
If you are in doubt, contact your
nearest MARUTI SUZUKI authorized
workshop.When Jump Starting Your Vehicle,
Use the Following Procedure:1) Use only a 12 volt battery to jump start
your vehicle. Position the good 12 V
battery close to your vehicle so that the
jump leads will reach both batteries.
When using a battery installed on
another vehicle, DO NOT LET THE

Downloaded from www.Manualslib.com manuals search engine 12583K
EMERGENCY SERVICE
10-4
83K-08-010
VEHICLES TOUCH. Apply the parking
brakes fully on both vehicles.
2) Turn off all vehicle accessories, except
those necessary for safety reasons (for
example, headlights or hazard lights).
3) Make jump lead connections as follows:
1. Connect one end of the first jump
lead to the positive (+) terminal of
the flat battery (1).
2. Connect the other end to the positive
(+) terminal of the booster battery (2).
3. Connect one end of the second jump
lead to the negative (–) terminal of
the booster battery (3).
4. Make the final connection to an
unpainted, heavy metal part (i.e.
engine mounting stud/nut (4)) of the
engine of the vehicle with the flat
battery (1).4) If the booster battery you are using is
fitted to another vehicle, start the engine
of the vehicle with the booster battery.
Run the engine at moderate speed.
5) Start the engine of the vehicle with the
flat battery.
6) Remove the jump leads in the exact
reverse order in which you connected them.
TowingIf you need to have your vehicle towed,
contact a Maruti Suzuki authorised dealer
/ service stations.
w ww w
w WARNING
Never connect the jump lead directly
to the negative (–) terminal of the dis-
charged battery, or an explosion may
occur.
CAUTION
To help avoid damage to your vehicle
during towing, proper equipment and
towing procedures must be used.
CAUTION
The steering colum is not strong
enough to withstand shocks trans-
mitted from the front wheels during
towing always unlock the steering
wheel before towing.
Your vehicle may be towed using either of
the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the ground.
Before towing, make sure that the
parking brake is released.
2) From the rear, with the rear wheels lifted
and the front wheels on the ground,provided the steering and drivetrain are
in operational condition. Before towing,
make sure that transmission is in neutral,
the steering wheel is unlocked (the
ignition key should be in the “ACC”
position), and the steering wheel is
secured with a clamping device designed
for towing service.If the Starter Does Not
Operate1) Try turning the ignition switch to the
“START” position with the headlights turned
on to determine the battery condition. If the
headlights go excessively dim or go off, it
usually means that either the battery is flat
or the battery terminal contact is poor.
Recharge the battery or correct battery
terminal contact as necessary.
2) If the headlights remain bright, check the
fuses. If the reason for failure of the
starter is not obvious, there may be a
major electrical problem. Have the vehi-
cle inspected by your MARUTI SUZUKI
authorized dealer.
EXAMPLE

Downloaded from www.Manualslib.com manuals search engine 12683K
EMERGENCY SERVICE
10-5
w ww w
w WARNING
If you see or hear escaping steam,
stop the vehicle in a safe place and
immediately turn off the engine to let
it cool. Do not open the hood when
steam is present. When the steam can
no longer be seen or heard, open the
hood to see if the coolant is still
boiling. If it is, you must wait until it
stops boiling before you proceed.If the Engine is FloodedIf the engine is flooded with Petrol, it may
be hard to start. If this happens, press the
accelerator pedal all the way to the floor
and hold it there while cranking the engine.
(Do not operate the starter motor for more
than 15 seconds).If the Engine OverheatsThe engine could overheat temporarily under
severe driving conditions. If the high engine
coolant temperature warning light comes on
as indication of overheating during driving:
1) Turn off the air conditioner, if equipped.
2) Take the vehicle to a safe place and park.
3) Let the engine run at the normal idle speed
for a few minutes until the high engine
coolant temperature warning light goes off.water pump belt and pulleys are not
damaged or slipping. If any abnormality
is found, contact your Maruti Suzuki
authorized workshop / service station.
2) Check the coolant level in the reservoir.
If it is found to be lower than the “LOW”
line, look for leaks at the radiator, water
pump, and radiator and heater hoses. If
you locate any leaks that may have
caused the overheating, do not run the
engine until these problems have been
corrected and contact your Maruti Suzuki
authorized workshop / service station.
3) If you do not find a leak, carefully add
coolant to the reservoir and then the
radiator, if necessary. (Refer to “Engine
Coolant” in the “INSPECTION AND
MAINTENANCE” section.)
83K-08-011
If the high engine coolant temperature
warning light does not go off:
1) Turn off the engine and check that the
83K-08-012
For Petrol
w ww w
w WARNING
It is hazardous to remove the radia-
tor cap (Petrol) or degassing tank
cap (Diesel) when the water tem-
perature is high, because scalding
fluid and steam may be blown out
under pressure. The cap should only
be taken off when the coolant
temperature has lowered.
To help prevent personal injury,
keep hands, tools and clothing away
from the engine cooling fan and air-
conditioner fan (if equipped). These
electric fans can automatically turn
on without warning.For Diesel

Downloaded from www.Manualslib.com manuals search engine 12883K
Certain cargos such as chemicals, fertiliz-
ers, cleaners, salts, etc. are extremely cor-
rosive by nature. These products should be
transported in sealed containers. If a spill
or leak does occur, clean and dry the area
immediately.APPEARANCE CAREStore your vehicle in a dry, well-venti-
lated area
Do not park your vehicle in a damp, poorly
ventilated area. If you often wash your
vehicle in the garage or if you frequently
drive it in when wet, your garage may be
damp. The high humidity in the garage may
cause or accelerate corrosion. A wet vehicle
may corrode even in a heated garage if the
ventilation is poor.
w ww w
w WARNING
Do not apply additional undercoating
or rust preventive coating on or
around exhaust system components
such as the catalytic converter,
exhaust pipes, etc. A fire could be
started if the undercoating substance
becomes overheated.
Vehicle Cleaning
83K-09-001
When cleaning the interior or exterior
of the vehicle, NEVER USE flammable
solvents such as lacquer thinners,
petrol, benzene or cleaning materials
such as bleaches or strong household
detergents. The materials could cause
personal injury or damage to the
vehicle.
w ww w
w WARNING
Cleaning the InteriorVinyl upholstery
Prepare a solution of soap or mild deter-
gent mixed with warm water. Apply the
solution to the vinyl with a sponge or soft
cloth and let it soak for a few minutes to
loosen dirt.Rub the surface with a clean, damp cloth
to remove dirt and the soap solution. If
some dirt still remains on the surface,
repeat this procedure.
Fabric upholstery
Remove loose dirt with a vacuum cleaner.
Using a mild soap solution, rub stained
areas with a clean damp cloth. To remove
soap, rub the areas again with a cloth
dampened with water. Repeat this until the
stain is removed, or use a commercial fab-
ric cleaner for tougher stains. If you use a
fabric cleaner, carefully follow the manu-
facturer’s instructions and precautions.
Seat belts
Clean seat belts with a mild soap and water.
Do not use bleach or dye on the belts. They
may weaken the fabric in the belts.
Vinyl floor mats
Ordinary dirt can be removed from vinyl with
water or mild soap. Use a brush to help
loosen dirt. After the dirt is loosened, rinse
the mat thoroughly with water and dry it in
the shade.
Carpets
Remove dirt and soil as much as possible
with a vacuum cleaner. Using a mild soap
solution, rub stained areas with a clean
damp cloth. To remove soap, rub the areas
again with a cloth dampened with water.
Repeat this until the stain is removed, or
11-2

Downloaded from www.Manualslib.com manuals search engine 12983K
APPEARANCE CARE
CAUTION
It is important that your vehicle be
kept clean and free from dirt. Failure
to keep your vehicle clean may result
in fading of the paint or corrosion to
various parts of the vehicle body. use a commercial carpet cleaner for tougher
stains. If you use a carpet cleaner, carefully
follow the manufacturer’s instructions and
precautions.Cleaning the Exterior
Washing
Never attempt to wash and wax your
vehicle with the engine running.
When cleaning the underside of the
body and fender, where there may
be sharp-edged parts, you should
wear gloves and a long sleeved
shirt to protect your hands and
arms from being cut.
After washing your vehicle, carefully
test the brakes before driving to
make sure they have maintained
their normal effectiveness.
w ww w
w WARNING
83K-09-002
When washing the vehicle, park it where
direct sunlight does not fall on it and follow
the instructions below:
1) Flush the underside of body and wheel
housings with pressurized water to remove
mud and debris. Use plenty of water.
CAUTION
When washing the vehicle, avoid
directing steam or hot water of more
than 80°C (176°F) on plastic parts.
To avoid damaging engine compo-
nents, do not use pressurized water
in the engine compartment.
2) Rinse the body to loosen the dirt.
Remove dirt and mud from the body
exterior with running water. You may usea soft sponge or brush. Do not use hard
materials which can scratch the paint or
plastic. Remember that the headlight
covers or lenses are made of plastic in
many cases.
CAUTION
To avoid damage to the paint or plas-
tic surface, do not wipe the dirt off
without ample water. Be sure to fol-
low above procedure.
3) Wash the entire exterior with a mild
detergent or car wash soap using a
sponge or soft cloth. The sponge or
cloth should be frequently soaked in the
soap solution.
CAUTION
When using a commercial car wash
product, observe the cautions speci-
fied by the manufacturer. Never use
strong household detergents or soaps.
4) Once the dirt has been completely
removed, rinse off the detergent with
running water.
5) After rinsing, wipe off the vehicle body
with a wet chamois or cloth and allow
it to dry in the shade.
6) Check carefully for damage to painted
surfaces. If there is any damage, “touch-
11-3