2005 SUZUKI MARUTI warning

Downloaded from www.Manualslib.com manuals search engine 9583KDrive Belt
w ww w
w WARNING
When the engine is running, keep
hands, hair, clothing, tools, etc. away
from the moving fan and drive belts.
(For Petrol Engine Model)
Make sure the drive belt tension is correct.
If the belt is too loose, insufficient battery
charging, engine overheating, poor power
steering, poor air conditioning, or excessive
belt wear can result. When you press the
belt with your thumb midway between the
pulleys, there should be a deflection
according to the following chart.
The belts should also be examined to
ensure that they are not damaged.
If you need to replace or adjust the belt
have it done by your MARUTI SUZUKI
dealer.
(For Diesel Engine Model)
The drive belts tension is adjusted auto-
matically.
Engine Oil and FilterSpecified Oil(For Petrol Engine Model)
(1) Preferred→: 100 N (10 kg, 22 lbs) press GE: Generator
DEF: Deflection AC: Air conditioner compressor
INSPECTION AND MAINTENANCE
9-6
83K-07-003
(For Diesel Engine Model)
83K-07-005
Be sure that the engine oil you use comes
under the quality classification of ACEA B3.
Select the appropriate oil viscosity according
to the above chart.
The recommended Engine Oil is CG
5W-40, API -CG4 or above.Oil Level Check(For Petrol Engine Model)
83K-07-006
(1) Preferred
83K-07-005
Be sure that the engine oil you use comes
under the quality classification of SG+.
The recommended Engine Oil is SG+
5W-30.

Downloaded from www.Manualslib.com manuals search engine 9683K
INSPECTION AND MAINTENANCE
9-7(For Diesel Engine Model)
83K-07-007
CAUTION
Failure to check the oil level regularly
could lead to serious engine trouble
due to insufficient oil.
(1) MIN
(2) MAX
(3) Engine oil dipstick
It is important to keep the engine oil at the
correct level for proper lubrication of your
vehicle’s engine. Check the oil level with the
vehicle on a level surface. The oil level
indication may be inaccurate if the vehicle
is on a slope. The oil level should be
checked either before starting the engine or
at least 5 minutes after stopping the engine.
The handle of the engine oil dipstick is col-
ored yellow for easy identification. Pull out
the oil dipstick, wipe oil off with a clean cloth,
insert the dipstick all the way into the engine,
then remove it again. The oil on the stick
should be between the upper and lower
limits shown on the stick. If the oil level
indication is near the lower limit, add enough
oil to raise the level to the upper limit.
83K-07-00883K-07-009
Refilling (Petrol)
Refilling (Diesel)Remove the oil filler cap and pour oil slowly
through the filler hole to bring the oil level
to the upper limit on the dipstick. Be careful
not to overfill. Too much oil is almost as
bad as too little oil. After refilling, start the
engine and allow it to idle for about a
minute. Stop the engine, wait about 5 min-
utes and check the oil level again.
Changing Engine Oil and FilterDrain the engine oil while the engine is still
warm.
83K-07-010
The engine oil temperature may be
high enough to burn your fingers
when the drain plug is loosened. Wait
until the drain plug is cool enough to
touch with your bare hands.
w ww w
w WARNING
1) Remove the oil filler cap.
2) Place a drain pan under the drain plug.
3) Using a wrench, remove the drain plug
and drain out the engine oil.

Downloaded from www.Manualslib.com manuals search engine 9783K
INSPECTION AND MAINTENANCE
9-8
83K-07-011
EXAMPLE For Petrol
For Diesel
EXAMPLETightening torque for drain plug (1):
Petrol Engine
35 Nm (3.5 kg-m, 25.5 lb-ft)
Diesel Engine
20 Nm (2.0 kg-m, 14.5 lb-ft)
NOTE:
Washer (2) should be replaced every time
when opened.
w ww w
w WARNING
New and used oil can be hazardous.
Children and pets may be harmed by
swallowing new or used oil. Keep new,
used oil and used oil filters away from
children and pets.
Continuous contact with used engine
oil may cause (skin) cancer.
Brief contact with used oil may irritate
skin.
To minimize your exposure to used
oil, wear a long-sleeve shirt and
moisture-proof gloves (such as dish-
washing gloves) when changing oil. If
oil contacts your skin, wash thor-
oughly with soap and water.
Launder any clothing or rags if wet
with oil.
Recycle or properly dispose of used
oil and filters.
4) Reinstall the drain plug and gasket.
Tighten the plug with a wrench to the
specified torque.Replace the Oil Filter1) Using an oil filter wrench, turn the oil fil-
ter counterclockwise and remove it.
2) Using a clean rag, wipe off the mount-
ing surface on the engine where the new
filter will be seated.3) Smear a little engine oil around the rub-
ber gasket of the new oil filter.
4) Screw on the new filter by hand until the
filter gasket contacts the mounting sur-
face.
(For Petrol Engine Model)
83K-07-012
83K-07-013
(1) Loosen
(2) Tighten
Tightening (viewed from filter top)
83K-07-014
(1) Oil filter
(2) 3/4 turn

Downloaded from www.Manualslib.com manuals search engine 9983K
INSPECTION AND MAINTENANCE
9-10
(For Diesel Engine Model)
83K-07-018
CAUTION
To avoid damaging your cooling system:
Always use a high quality ethylene
glycol base non-silicate based
coolant diluted with distilled water
at the correct mixture concentration.
Make sure that the proper mix is 50/
50 coolant to distilled water (Diesel)
and 30/70 (For petrol). Concen-
trations other than this may cause
overheating conditions.
Neither use 100% coolant nor 100%
plain water.
Do not add extra inhibitors or addi-
tives. They may not be compatible
with your cooling system.
Do not mix different types of base
coolants. Doing so may result in
accelerated seal wear and/or the
possibility of severe overheating and
extensive engine damage.Coolant Level CheckCheck the coolant level at the reservoir
tank, not at the radiator. With the engine
cool, the coolant level should be between
the “FULL” and “LOW” marks.
Selection of CoolantTo maintain optimum performance and
durability of your engine, use MARUTI
Genuine Coolant or equivalent.
This type of coolant is best for your cooling
system as it:
Helps maintain proper engine tempera-
ture.
Gives proper protection against freezing
and boiling.
Gives proper protection against corrosion
and rust.
Failure to use the proper coolant can dam-
age your cooling system. Your MARUTI
SUZUKI authorized dealer can help you
select the proper coolant.
w ww w
w WARNING
It is hazardous to remove the reservoir
tank cap (degassing tank cap) for Diesel
engine when the water temperature is
high, because scalding fluid and steam
may be blown out under pressure. Wait
until the coolant temperature has
lowered before removing the cap.
Adding Coolant(For Petrol Engine Model)
If the coolant level is below the “LOW”
mark, more coolant should be added.Remove the reservoir tank cap and add
coolant until the reservoir tank level reaches
the “FULL” mark. Never fill the reservoir
tank above the “FULL” mark.
(For Diesel Engine Model)
If the coolant level is below the “LOW”
mark, more coolant should be added. When
the engine is cool, remove the degassing
tank cap by turning it anticlockwise slowly
to release any pressure. And add coolant
until the degassing tank level reaches the
“FULL” mark. Never fill the degassing tank
above the “FULL” mark.
The mixture you use should contain
50% concentration of antifreeze.
If the lowest ambient temperature in
your area is expected to be – 35°C
(–31°F) or below, use higher
concentrations up to 60% following
CAUTION
V VV V
V

Downloaded from www.Manualslib.com manuals search engine 10083K
INSPECTION AND MAINTENANCE
9-11
CAUTION
the instructions on the antifreeze
container.
When putting the cap on the reser-
voir tank, line up the arrow on the
cap and the arrow on the tank. Fail-
ure to follow this can result in cool-
ant leakage.
Engine coolant is harmful or fatal if
swallowed or inhaled. Do not drink
antifreeze or coolant solution. If swal-
lowed, do not induce vomiting. Imme-
diately contact a poison control center
or a physician. Avoid inhaling mist or
hot vapors; if inhaled, remove to fresh
air. If coolant gets in eyes, flush eyes
with water and seek medical attention.
Wash thoroughly after handling.
Solution can be poisonous to animals.
Keep out of the reach of children and
animals.
w ww w
w WARNING
V VV V
V
Coolant ReplacementCoolant Replacement work requires tech-
nical skill. Do not replace the coolant by
yourself. Trust this job to Maruti Suzuki
authorised Dealer Workshop or Service
Station.
Air Cleaner(For Petrol Engine Model)
83K-07-01983K-07-020
(For Diesel Engine Model)
If the air cleaner is clogged with dust, there
will be greater intake resistance, resultingin decreased power output and increased
fuel consumption.
Unclamp the side clamps or loosen the
screws, and remove the element from the
air cleaner case. If it appears to be dirty,
replace it with a new one.
Spark Plugs
83K-07-021

Downloaded from www.Manualslib.com manuals search engine 10283K
INSPECTION AND MAINTENANCE
9-13
CAUTION
fied for your vehicle. For the specified
spark plugs, refer to the “SPECIFI-
CATIONS” section at the end of this
book. It is recommended to trust this
job on your MARUTI SUZUKI dealer.
83K-07-026
NOTE:
If your engine is equipped with the high-
tension cord type ignition wiring and you
experience some firing problem of spark
plugs, such as, hard engine-starting, misfire
etc., the cause may be located not only on
spark plugs but also on deteriorated ignition
wirings (generally, used for more than 80000
km or five years). If spark plug replacement
does not solve the problem, have theEXAMPLEV VV V
V
ignition wiring and other ignition system
inspected by your MARUTI SUZUKI dealer.Gear OilTransmission OilWhen adding gear oil, use gear oil with the
appropriate viscosity and grade.
We highly recommend you use:
API GL-4 SAE 75W-90.
83K-07-027
Gear Oil Level Check
(1) Oil filler and level plug
(for petrol engine model)
(2) Oil filler and level plug
(for diesel engine model)
To check the gear oil level, use the follow-
ing procedure:
1) Park the vehicle on a level surface withthe parking brake applied. Then, stop the
engine.
2) Remove the oil filler plug.
3) Feel the inside of the hole with your fin-
ger. If the oil level comes up to the bot-
tom of the plug hole, the oil level is
correct. If so, reinstall the plug.
4) If the oil level is low, add gear oil
through the oil filler plug hole (1) until
the oil level reaches the bottom of the
filler hole, then reinstall the plug.
Tightening torque (1):
21 Nm (2.1 kg-m, 15.5 lb-ft)
w ww w
w WARNING
After driving the vehicle, the trans-
mission oil temperature may be high
enough to burn your skin. Wait until
the oil filler plug is cool enough to
touch with your bare hands before
inspecting transmission oil.
CAUTION
When tightening the plug, apply the
following sealing compound or
equivalent to the plug threads to pre-
vent oil leakage.
Manual transmission sealant:
SUZUKI Bond No. “1217G”

Downloaded from www.Manualslib.com manuals search engine 10483K
hot weather, or if the vehicle has been
pulling a trailer. Wait until the fluid cools
down (about 30 minutes), or the fluid level
indication will not be correct.
83K-07-029A
INSPECTION AND MAINTENANCE
9-152) Park your vehicle on level ground.
3) Apply the parking brake and then start
the engine in “P” (Park). Let it idle for
two minutes and keep it running during
the fluid level check.
4) With your foot on the brake pedal, move
the gearshift lever through each range,
pausing for about three seconds in each
range. Then move it back to the “P”
(Park) position.Be sure to depress the brake pedal
when moving the gearshift lever, or
the vehicle can move suddenly.
w ww w
w WARNING
83K-07-029B
5) The handle of the A/T fluid dipstick is
colored red or orange for easy identi-
fication.
Remove the dipstick, clean it and push
it back in until the cap seats. Then pull
out the dipstick.
6) Check both sides of the dipstick, and
read the lowest level. The fluid level
should be between the two marks in the
“HOT” range on the dipstick.(1) FULL HOT
(2) LOW HOT
(3) The lowest point = Fluid level
7) Add just enough specified fluid through
the dipstick hole to fill the transaxle to
the proper level.
83K-07-029C
EXAMPLE
NOTICE
After checking or adding oil, be sure
to insert the dipstick securely.Changing OilSince special procedures, materials, and
tools are required to change the automatic
transaxle oil, it is recommended that you
trust this job to your authorized d MARUTI
SUZUKI dealer.
EXAMPLE
EXAMPLE

Downloaded from www.Manualslib.com manuals search engine 10683K
INSPECTION AND MAINTENANCE
9-17BrakesBrake FluidCheck the brake fluid level by looking at the
reservoir in the engine compartment. Check
that the fluid level is between the “MAX”
and “MIN” lines. If the brake fluid level is
near the “MIN” line, fill it up to the “MAX”
line with Maruti Genuine brake fluid.
83K-07-031
EXAMPLEFailure to follow the guidelines below
can result in personal injury or seri-
ous damage to the brake system.
If the brake fluid in the reservoir
drops below a certain level, the
brake warning light on the instru-
ment panel will come on (the engine
must be running with the parking
w ww w
w WARNING
V VV V
V
w ww w
w WARNING
V VV V
Vbrake fully disengaged). If the light
comes on, immediately contact your
MARUTI SUZUKI dealer to inspect
the brake system.
A rapid fluid loss indicates a leak in
the brake system which should be
inspected by your MARUTI SUZUKI
dealer immediately.
Brake fluid can harm your eyes and
damage painted surfaces. Use cau-
tion when refilling the reservoir.
Do not use any fluid other than
specified brake fluid. Do not use
reclaimed fluid or fluid that has
been stored in old or open contain-
ers. It is essential that foreign parti-
cles and other liquids are kept out
of the brake fluid reservoir.
V VV V
V
Brake fluid is harmful or fatal if swal-
lowed, and harmful if it comes in con-
tact with skin or eyes. If swallowed,
do not induce vomiting. Immediately
contact a poison control center or a
physician. If brake fluid gets in eyes,
flush eyes with water and seek medi-
cal attention. Wash thoroughly after
handling. Solution can be poisonous
w ww w
w WARNING
V VV V
Vto animals. Keep out of the reach of
children and animals.NOTE:
With disc brakes, the fluid level can be
expected to gradually fall as the brake pads
wear.Brake PedalCheck if the brake pedal stops at the regu-
lar height without “spongy” feeling when you
depress it. If not, have the brake system
inspected by your MARUTI SUZUKI dealer.
If you doubt the brake pedal for the regular
height, check it as follows:
83K-07-032
Pedal to wall minimum distance “a”:
85 mm (3.3 in.)
w ww w
w WARNING