2005 SUZUKI GRAND VITARA warning

YH4
GRAND
VITARA
1. Buckle tongue
2. Buckle catch
10A-4 SEAT BELT
INSPECTION
Seat belts and attaching parts can affect the vital components and
systems of a vehicle. Therefore, they should be inspected carefully
and replaced with genuine parts only.
Seat belt

The seat belt webbing or strap should be free from damage.

Fully extend the seat belt to make sure there are no twists or tears
in it.
Retractor assembly
Let the seat belt retract fully to confirm its easy retraction.

The retractor assembly should lock webbing when pulled quickly.

The retractor assembly should lock webbing even when tilted
(approx. 15) toward the fore and aft or right and left directions.
Anchor bolt

Inspect all seat belt anchor bolts to verify that they are secure.

All anchor bolts should be secure and torqued to specification.
Belt latch

Belt latch should be secure when latched.

Inspect the seat belt buckle, ensuring that it locks and unlocks
easily.

After buckling the seat belt, tug sharply on the belt, checking that
the buckle remains locked.
Warning system
Check driver side seat belt strap switch for continuity by using ohm-
meter.
Without inserted buckle tongue to buckle catch:
Terminal ªAº and ªBº: Continuity
With inserted buckle tongue to buckle catch:
Terminal ªAº and ªBº: No continuity (

)
As to seat belts with ALR (other than driver side seat belt), check
them as follows in addition to above check.

With vehicle at stop, pull seat belt all the way out, let it retract a
little and try to pull it. It should not be pulled out, that is, it should
be locked where retracted.

Let seat belt retract to its original state. Next, pull it half way out,
let it retract a little and try to pull it again. It should be pulled out
smoothly, that is it should not be locked at this time.

YH4
GRAND
VITARA
10A-6 SEAT BELT
1. Upper anchor
2. Lower anchor
3. Retractor assembly
4. Buckle: If equipped* *
REAR SEAT BELT
WARNING:
Be sure to read ªService Precautionsº before starting to work and observe every precaution during
work.
REMOVAL
Refer to the figure below to remove rear seat belts.
INSPECTION
Check the rear seat belt in the same way as when inspecting front seat belt. (Refer to page 10A-4.)
INSTALLATION
Install the rear seat belt observing the same precautions as when installing front seat belt. (Refer to page 10A-5.)
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Upper and lower anchor bolt353.525.5
Retractor assembly bolt353.525.5
Retractor assembly screw5.50.554.0
Buckle bolt353.525.5

YH4
GRAND
VITARA
10B
AIR BAG SYSTEM 10B-1
GENERAL DESCRIPTION10B- 3 . . . . . . . . . . . . .
System Components and Wiring
Location View and Connectors 10B- 4. . . . . . .
System Wiring Diagram 10B- 5. . . . . . . . . . . . . .
DIAGNOSIS10B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Codes 10B- 6. . . . . . . . . . . .
Use of Special Tools 10B- 6. . . . . . . . . . . . . . . . .
Intermittent and Poor Connections 10B- 8. . . . .
Air Bag Diagnostic System Check 10B-10. . . . .
Air bag diagnostic system check
flow table 10B-11. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code (DTC) check 10B-12.
Diagnostic trouble code (DTC)
clearance 10B-13. . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code table 10B-14. . . . . . . .
Table A - ªAIR BAGº warning lamp
comes ªONº steady 10B-16. . . . . . . . . . . . . . .
Table B - ªAIR BAGº warning lamp
does not come ªONº 10B-18. . . . . . . . . . . . . .
Table C - ªAIR BAGº warning lamp
flashes 10B-20. . . . . . . . . . . . . . . . . . . . . . . . . .
Table D - SDM cannot communicate
through the serial data circuit 10B-22. . . . . . . Code 15 - Passenger air bag initiator
circuit resistance high 10B-24. . . . . . . . . . . . .
Code 16 - Passenger air bag initiator
circuit resistance low 10B-26. . . . . . . . . . . . . .
Code 18 - Passenger air bag initiator
circuit short to ground 10B-28. . . . . . . . . . . . .
Code 19 - Passenger air bag initiator
circuit short to power circuit 10B-30. . . . . . . .
Code 21 - Driver air bag initiator
circuit resistance high 10B-32. . . . . . . . . . . . .
Code 22 - Driver air bag initiator
circuit resistance low 10B-34. . . . . . . . . . . . . .
Code 24 - Driver air bag initiator
circuit short to ground 10B-36. . . . . . . . . . . . .
Code 25 - Driver air bag initiator
circuit short to power circuit 10B-38. . . . . . . .
Code 31 - Power source voltage high 10B-40
Code 32 - Power source voltage low 10B-42.
Code 41 - Driver pretensioner initiator
circuit resistance high 10B-44. . . . . . . . . . . . .
Code 45 - Passenger pretensioner
initiator circuit resistance high 10B-44. . . . . .
Code 42 - Driver pretensioner initiator
circuit resistance low 10B-46. . . . . . . . . . . . . .
SECTION 10B
AIR BAG SYSTEM
WARNING:

Service on or around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in this section before performing service on or around the air bag system components or
wiring. Failure to follow WARNINGS could result in unintended activation of the system or could ren-
der the system inoperative. Either of these two conditions may result in severe injury.

The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above condi-
tions are not followed, parts or system damage could result.
CONTENTS

YH4
GRAND
VITARA
10B-2 AIR BAG SYSTEM
Code 46 - Passenger pretensioner
initiator circuit resistance low 10B-46. . . . . . .
Code 43 - Driver pretensioner initiator
circuit short to ground 10B-48. . . . . . . . . . . . .
Code 47 - Passenger pretensioner
initiator circuit short to ground 10B-48. . . . . .
Code 44 - Driver pretensioner initiator
circuit short to power circuit 10B-50. . . . . . . .
Code 48 - Passenger pretensioner
initiator circuit short to power circuit 10B-50.
Code 51 - Frontal crash detected
(System activation command is
outputted) 10B-52. . . . . . . . . . . . . . . . . . . . . . .
Code 61 -ªAIR BAGº warning lamp
circuit failure 10B-53. . . . . . . . . . . . . . . . . . . . .
Code 71 - Internal SDM fault 10B-54. . . . . . . .
ON-VEHICLE SERVICE10B-55 . . . . . . . . . . . . . . .
Service Precautions 10B-55. . . . . . . . . . . . . . . . .
Service and diagnosis 10B-55. . . . . . . . . . . . . .
Disabling air bag system 10B-56. . . . . . . . . . . .
Enabling air bag system 10B-56. . . . . . . . . . . .
Handling and storage 10B-57. . . . . . . . . . . . . .
Disposal 10B-62. . . . . . . . . . . . . . . . . . . . . . . . . .
Repairs and Inspections Required
after an Accident 10B-63. . . . . . . . . . . . . . . . . . .
Accident with deployment
- component replacement 10B-63. . . . . . . . . . Accident with or without deployment
- component inspections 10B-64. . . . . . . . . . .
Driver Air Bag (Inflator) Module 10B-66. . . . . . . .
Contact Coil and Combination Switch
Assembly 10B-66. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Pretensioner 10B-66. . . . . . . . . . . . . . .
ªAIR BAGº Warning Lamp 10B-66. . . . . . . . . . . .
SDM 10B-67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Passenger Air Bag (Inflator) Module 10B-69. . .
AIR BAG (INFLATOR) MODULES
DISPOSAL10B-71 . . . . . . . . . . . . . . . . . . . . . . . . . .
Deployment Outside Vehicle 10B-71. . . . . . . . . .
Deployment Inside Vehicle 10B-78. . . . . . . . . . . .
SEAT BELT PRETENSIONERS
DISPOSAL10B-83 . . . . . . . . . . . . . . . . . . . . . . . . . .
Activation Outside Vehicle 10B-83. . . . . . . . . . . .
Activation Inside Vehicle 10B-89. . . . . . . . . . . . . .
DEPLOYED AIR BAG (INFLATOR)
MODULES DISPOSAL10B-93 . . . . . . . . . . . . .
ACTIVATED SEAT BELT PRETENSIONERS
DISPOSAL10B-94 . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS10B-95 . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS10B-95 . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
WIRE HARNESS COLOR
B : Black
B/W : Black/White
Bl : Blue
Bl/B : Blue/Black
Bl/R : Blue/Red
Br : BrownG : Green
Gr : Gray
G/R : Green/Red
Lg : Lightgreen
P : Pink
V : VioletY : Yellow
Y / G : Yellow/Green
Y/R : Yellow/Red
W : White
W/B : White/Black
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B
4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin
7. To ECM (or PCM), ICM (if equipped) and ABS
controller (if equipped)
8. To data link connector (DLC)
9. ªAIR BAGº monitor coupler
10. SDM
11. Contact coil assembly
12. Driver air bag (inflator) module
13. Driver seat belt pretensioner (if equipped)
14. Passenger air bag (inflator) module
15. Passenger seat belt pretensioner (if equipped)
16. Pretensioner harness (if equipped)
17. Ground for air bag system
TERMINAL
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A13 A11
A12
A14
A15
A16
Passenger air bag (inflator) moduleLow
High
CIRCUIT
Data link connector (DLC)
Low
High
Low
High
Low
High ªAIR BAGº warning lamp
Driver air bag (inflator) module
Diagnosis switch
±±±±±±±±±
Ground
Passenger pretensioner
Driver pretensioner
Ignition switch (power source)±±±±±±±±±
±±±±±±±±±
CONNECTOR ªAº (SDM connector) TERMINAL ARRANGEMENT OF SDM
(VIEWED FROM HARNESS SIDE)
L1
L2Connection detection pin
: Shorting bar
: Air bag harness
ªAº
ªHº : Connector
AIR BAG SYSTEM 10B-5
SYSTEM WIRING DIAGRAM

YH4
GRAND
VITARA
(A)(A)
(A)
10B-6 AIR BAG SYSTEM
DIAGNOSIS
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
DIAGNOSTIC TROUBLE CODES
The ªAir Bag Diagnostic System Checkº must always be the starting point of any air bag system diagnosis. The
ªAir Bag Diagnostic System Checkº checks for proper ªAIR BAGº warning lamp operation and checks for air bag
diagnostic trouble codes using the Tech-1 (scan tool) or on-board diagnosis function.

Current diagnostic trouble code ± Malfunction that are presently being detected.

History diagnostic trouble code ± All malfunction detected since the last time the history memory was cleared.
USE OF SPECIAL TOOLS
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
You should be familiar with the tools listed under ªSpecial Toolsº in this section. You should be able to measure
voltage and resistance. You should be familiar with proper use of a scan tool such as the Tech-1 Diagnostic Com-
puter, Driver/Passenger Load Tool, Connector Test Adapter Kit and the Digital Multimeter.
Special Tool (Connector Test Adapter Kit)
(A): 09932-76010
This must be used whenever a diagnostic procedure requests
checking or probing a terminal.
Using the appropriate adapter in the special tool will ensure that no
damage to the terminal will occur from the multimeter probe, such
as spreading or bending.
The adapter will also give an idea of whether contact tension is suffi-
cient, helping to find an open or intermittent open due to poor termi-
nal contact.

YH4
GRAND
VITARA
10B-10 AIR BAG SYSTEM
AIR BAG DIAGNOSTIC SYSTEM CHECK
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
CAUTION:
The order in which diagnostic trouble codes are diagnosed is very important. Failure to diagnose the
diagnostic trouble codes in the order specified may result in extended diagnostic time, incorrect diag-
nosis and incorrect parts replacement.
The diagnostic procedures used in this section are designed to find and repair air bag system malfunctions.
To get the best results, it is important to use the diagnostic flow tables and follow the sequence listed below.
A. PERFORM THE ªAIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLEº
The ªAir Bag Diagnostic System Check Flow Tableº must be the starting point of any air bag system diagnostics.
The ªAir Bag Diagnostic System Check Flow Tableº checks for proper ªAIR BAGº warning lamp operation, the
ability of the SDM to communicate through ªAIR BAGº warning lamp and whether air bag diagnostic trouble
codes exist.
B. REFER TO THE PROPER DIAGNOSTIC TABLE AS DIRECTED BY THE ªAIR BAG DIAGNOSTIC SYSTEM
CHECK FLOW TABLEº.
The ªAir Bag Diagnostic System Check Flow Tableº will lead you to the correct chart to diagnose any air bag
system malfunctions. Bypassing these procedures may result in extended diagnostic time, incorrect diagnosis
and incorrect parts replacement.
C. REPEAT THE ªAIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLEº AFTER ANY REPAIR OR DIAGNOS-
TIC PROCEDURES HAVE BEEN PERFORMED.
Performing the ªAir Bag Diagnostic System Check Flow Tableº after all repair or diagnostic procedures will en-
sure that the repair has been made correctly and that no other malfunctions exist.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-11
AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE
STEPACTIONYESNO
11) Make sure that battery voltage is about
11V or higher.
2) Note ªAIR BAGº warning lamp as ignition
switch is tuned ON.
3) Does ªAIR BAGº warning lamp flash
6 times when ignition switch is tuned ON?Go to step 2.ªAIR BAGº warning lamp
does not come ªONº
Proceed to ªTable Bº
on p.10B-18.
2Does ªAIR BAGº warning lamp keep flashing
(indicating DTC) when ignition switch is
turned ON ?ªAIR BAGº warning
lamp flashes
Proceed to ªTable Cº
on p.10B-20.Go to step 3.
3After flashing 6 times then does
ªAIR BAGº warning lamp turn OFF?Go to step 4.Go to step 5.
41) Check DTC, referring to ªDiagnostic
Trouble Code (DTC) Checkº on
p.10B-12.
2) [Using SUZUKI scan tool]
Is ªNO CODESº displayed ?
NOTE:
If SDM cannot communicate through
serial data circuit, proceed to ªTable
Dº on p.10B-22.
[Not using SUZUKI scan tool]
Is DTC 12 indicated ?Air bag system is in
good condition.NOTE:
As execution of the ªDiag-
nostic Trouble Code (DTC)
Clearanceº will clear all
DTCs, be sure to record all
DTCs before servicing.
An intermittent trouble has
occurred at some place.
Check the connector
harness, etc. related to the
sensed DTC (Refer to
ªIntermittent and Poor
Connectionsº in this section.).
Then clear DTC (Refer to
p.10B-13.) and repeat this
table.
51) Check DTC, referring to ªDiagnostic
Trouble Code (DTC) Checkº on
p.10B-12.
2) [Using SUZUKI scan tool]
Is ªNO CODESº displayed ?
NOTE:
If SDM cannot communicate through
serial data circuit, proceed to ªTable
Dº on p.10B-22.
[Not using SUZUKI scan tool]
Is DTC 12 indicated ?ªAIR BAGº warning
lamp come ªONº
steady
Proceed to ªTable Aº on
p.10B-16.NOTE:
As execution of the ªDiag-
nostic Trouble Code (DTC)
Clearanceº will clear all
DTCs, be sure to record all
DTCs before servicing.
Check and repair according
to Flow Table corresponding
to that DTC.