2005 SUBARU LEGACY ECO mode

1-18
Seat, seatbelt and SRS airbags
!
Expectant mothers
Expectant mothers also need to use the seatbelts.
They should consult their doctor for specific recom-
mendations. The lap belt should be worn securely and
as low as possible over the hips, not over the waist. ! Emergency Locking Retractor (ELR)
The driver’s seatbelt has an Emergency Locking Re-
tractor (ELR).
The emergency locking retractor allows normal body
movement but the retractor locks automatically during
a sudden stop, impact or if you pull the belt very quick-
ly out of the retractor. !
Automatic/Emergency Locking Retrac- tor (A/ELR)
Each passenger’s seatbelt has an Automatic/Emer-
gency Locking Retractor (A/ELR). The Automatic/
Emergency Locking Retractor normally functions as
an Emergency Locking Retractor (ELR). The A/ELR
has an additional locking mode “Automatic Locking
Retractor (ALR) mode” intended to secure a child re-
straint system. When the seatbelt is once drawn out
completely and is then retracted even slightly, the re-
tractor locks the seatbelt in that position and the seat-
belt cannot be extended. As the belt is rewinding,
clicks will be heard which indicate the retractor func-
tions as ALR. When the seatbelt is retracted fully, ALR
mode is released.
When securing a child restraint system on the passen-
gers’ seats, the seatbelt must be changed over to the
Automatic Locking Retractor (ALR) mode.
When the child restraint system is removed, make
sure that the retractor is restored to the Emergency
Locking Retractor (ELR) function by allowing the seat-
belt to retract fully.
For instructions on how to convert the retractor to the
ALR mode and restore it to the ELR mode, see the “Child restraint systems” section in this chapter.
HS1107AA

1-20
Seat, seatbelt and SRS airbags
seconds later (21 seconds after turning ON the ignition
switch), the warning lights will alternate between flash-
ing and steady illumination at 15-second intervals, and
the chime will sound while the warning light(s) is/are
flashing.
Alternate flashing and steady illumination of the warn-
ing lights and sounding of the chime will continue until
both driver and front passenger fasten their seatbelts.
NOTE "
If the driver and/or front passenger unfasten(s)
the seatbelt(s) after fastening, the seatbelt warn-
ing device operates as follows according to the
vehicle speed. "At speeds lower than approximately 9 mph (15
km/h)The warning light(s) for unfastened seatbelt(s)
will alternate between flashing and steady illu-
mination at 15-second intervals. The chime will
not sound. " At approximately 9 mph (15 km/h) or higher
speeds The warning light(s) for unfastened seatbelt(s)
will alternate between flashing and steady illu-
mination at 15-second intervals and the chime
will sound while the warning light(s) is/are flash-
ing.
" It is possible to cancel the warning operation that follows the 6-second warning after turning ON
the ignition switch by unfastening and refastening
the driver’s seatbelt. When the ignition switch is
turned ON next time, however, the complete se-
quence of warning operation resumes. For further
details about canceling the warning operation,
please contact your SUBARU dealer.
If there is no passenger on the front passenger’s seat,
the seatbelt warning device for front passenger’s seat
will be deactivated. The front passenger’s occupant
detection system monitors whether or not there is a
passenger on the front passenger’s seat.
Observe the following precautions. Failure to do so
may prevent the device from functioning correctly or
cause the device to fail. "
Do not install any accessory such as a table or TV
onto the seatback. " Do not store a heavy load in the seatback pocket.
" Do not allow the rear seat occupant to place his/her
hands or legs on the front passenger’s seatback, or al-
low him/her to pull the seatback. " Do not use front seats with their backward-forward
position and seatback not being locked into place se-
curely. If any of them are not locked securely, adjust
them again. For adjusting procedure, refer to the
“Manual seat” in the front seats section in Chapter 1 in
this owner’s manual. (Models equipped with manual

1-72
Seat, seatbelt and SRS airbags
seat, activating the front passenger’s SRS frontal air-
bag even though that seat is occupied by a child."
Do not place any article on the seat other than the
child occupant and a child restraint system." Do not place more than one child on the seat.
" Do not install any accessory such as a table or TV
onto the seatback." Do not store a heavy load in the seatback pocket.
" Do not allow the rear seat occupant to place his/her
hands or legs on the front passenger’s seatback, or al-
low him/her to pull the seatback. " If the front passenger’s frontal airbag ON indi-
cator illuminates and the OFF indicator extin-
guishes even when an infant or a small child is
in a child restraint system (including booster
seat)
Turn the ignition switch to the “OFF” position if the
front passenger’s frontal airbag ON indicator illumi-
nates and the OFF indicator extinguishes even when
an infant or a small child is in a child restraint system
(including booster seat). Remove the child restraint
system from the seat. By referring to the child restraint
manufacturer’s recommendations as well as the child
restraint system installation procedures in the “Child
restraint systems” section in this chapter, correctly in-
stall the child restraint system. Turn the ignition switch
to the “ON” position and make sure that the front pas- senger’s frontal airbag ON indicator goes out and the
OFF indicator comes on.
If still the ON indicator illuminates while the OFF indi-
cator extinguishes, take the following actions. "
Ensure that no article is placed on the seat other
than the child restraint system and the child occupant. " Ensure that there is no article left in the seatback
pocket. " Ensure that the backward-forward position and
seatback of front passenger’s seat are locked into
place securely by moving the seat back and forth.
(Models equipped with manual seats only)
If the ON indicator still illuminates while the OFF indi-
cator extinguishes after taking relevant corrective ac-
tions described above, relocate the child restraint sys-
tem to the rear seat and immediately contact your
SUBARU dealer for an inspection.
NOTE
When a child who has outgrown a child restraint
system or a small adult is seated in the front pas-
senger’s seat, the Subaru advanced frontal airbag
system may or may not activate the front passen-
ger’s SRS frontal airbag depending on the occu-
pant’s seating posture. If the front passenger’s
SRS frontal airbag is activated (the ON indicator il-
luminates while the OFF indicator extinguishes),

1-80
Seat, seatbelt and SRS airbags
struck from side or from behind, or if it rolls onto its
side or roof, or if it is involved in a low-speed frontal
collision.
A) First impact
B) Second impact
In an accident where the vehicle is impacted more
than once, the driver’s and/or front passenger’s SRS
frontal airbag(s) will deploy only once on the first im-
pact.
Example: In the case of a double collision, first with an-
other vehicle, then against a concrete wall in immedi-
ate succession, once either or both of the driver’s and
front passenger’s SRS frontal airbags is/are activated on the first impact, it/they will not be activated on the
second impact. !
SRS side airbag and SRS curtain air- bag
The SRS side airbag is stored in the door side of each
front seatback, which bears an “SRS AIRBAG” label.
In a moderate to severe side impact collision, the SRS
side airbag on the impacted side of the vehicle de-
ploys between the occupant and the door panel and
supplements the seatbelt by reducing the impact on
the occupant’s chest.
The SRS curtain airbag on each side of the cabin is
stored in the roof side (between the front pillar and a
point over the rear seat). An “SRS AIRBAG” mark is lo-
cated at the top of each center pillar.
In a moderate to severe side impact collision, the SRS
curtain airbag on the impacted side of the vehicle de-
ploys between the occupant and the side window and
supplements the seatbelt by reducing the impact on
the occupant’s head.
The SRS side airbag and SRS curtain airbag are
designed as only a supplement to the primary
protection provided by the seatbelt. It does not
B
A
US1559BB

2-25
Keys and doors
– CONTINUED –
6. Briefly press the “ ” button (for less than two sec-
onds). All doors (and the rear gate on the Station wag-
on) will lock, an electronic chirp will sound one time,
the turn signal lights will flash one time and the indica-
tor light starts flashing slowly (approximately twice ev-
ery two seconds).
The system will then be armed for surveillance after a
standby time of approximately 30 seconds.
If any of the doors, (rear gate or trunk lid) is not fully
closed, an electronic chirp sounds five times, the turn
signal lights flash five times to alert you that the doors
(or the rear gate) are not properly closed. When you
close the door, the system will automatically arm and doors will automatically lock.
NOTE "
The system can be armed even if the engine
hood, the windows and/or moonroofs are opened.
Always make sure that they are fully closed before
arming the system. " The 30-second standby time can be eliminated if
you prefer. Have it performed by your SUBARU
dealer. " If your vehicle is a Sedan and you unlock the
trunk using the remote transmitter’s “ ” but-
ton with the alarm system armed, the system will
be temporarily placed in a standby state. The sys-
tem will go back to the surveillance state upon
locking the trunk. " The system is in the standby mode for a 30-sec-
ond period after locking the doors with the remote
transmitter. The security indicator light will flash
at short intervals during this period. " If any of the following actions is done during the
standby period, the system will not switch to the
surveillance state. "Doors are unlocked using the remote trans-
mitter." Any door (including the rear gate of a Station
wagon or the trunk of a Sedan) is opened. " Ignition switch is turned to the “ON” position.
UB7507KA

2-26
Keys and doors
"
The alarm system is triggered when the ignition
switch is turned to the “ON” position during sur-
veillance. However, this does not occur if the vehi-
cle is equipped with an immobilizer and the key
used for turning the ignition switch has been reg-
istered. " If your vehicle is not equipped with an immobi-
lizer, the engine does not start even when the igni- tion switch is turned to the “START” position once
the alarm system has been triggered. ! Disarming the system
Briefly press the “ ” button (for less than two sec-
onds) on the remote transmitter. The driver’s door will
unlock, an electronic chirp will sound twice, the turn
signal lights will flash twice and the indicator light will
go off.
To unlock all other doors and the rear gate (Station
wagon), briefly press the “ ” button a second time.
NOTE
If the interval between the first and second press-
es of the “ ” button (for unlocking of all of the
doors and the rear gate) is extremely short, the
system may not respond.
Or the system can be disarmed by the following method, too. "
Insert the key in the door lock of the driver’s
door and turn it to the unlock position." Cycle the ignition switch from the “LOCK” to the
“ON” position three times within 5 seconds (only
vehicle without immobilizer). ! Emergency disarming
If you cannot disarm the system using the transmitter
(i.e. the transmitter is lost, broken or the transmitter
battery is too weak), you can disarm the system with-
out using the transmitter.
Vehicle with immobilizer
The system can be disarmed if you turn the ignition
switch from the “LOCK” to the “ON” position with a reg-
istered key.
Vehicle without immobilizer
1. Unlock the door with the key and then open the
door.
2. Insert the key into the ignition switch and cycle it
from the “LOCK” to the “ON” position three times with-
in 5 seconds .
All models
Insert the key in the door lock of the driver’s door and
turn it to the unlock position.

2-27
Keys and doors
– CONTINUED –
!Valet mode
When you choose the valet mode, the alarm system
does not operate. In valet mode, the remote transmit-
ter is used only for locking and unlocking the doors
and rear gate (Station wagon) and panic activation.
To enter the valet mode, change the setting of your ve-
hicle’s alarm system for deactivation mode. (Refer to
“Activating and deactivating the alarm system” in this
section.) The security indicator light will continue to
flash once every three seconds indicating that the sys-
tem is in the valet mode (only vehicle with an immobi- lizer).
To exit valet mode, change the setting of your vehi-
cle’s alarm system for activation mode. (Refer to “Ac-
tivating and deactivating the alarm system” in this sec- tion.)
NOTE
If your vehicle is not equipped with an immobiliz-
er, the security indicator light does not flash dur-
ing the valet mode. ! Passive arming
When passive arming mode has been programmed by
the dealer, arming of the system is automatically ac-
complished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLYLOCKED. !
To enter the passive mode
If you wish to program the passive arming mode, have
it done by your SUBARU dealer. ! Arming the system
In passive mode, the system will automatically
activate the alarm but WILL NOT automatically
lock the doors. In order to lock the doors you
must either lock them as indicated in step 4 be-
low or with the key once they have been closed.
Failure to lock the doors manually will result in
a higher security risk.
1. Turn the ignition switch to the “ON” position.

3-10
Instruments and controls
the “ON” position within 10 seconds of illumination of
the odometer/trip meter. !
Double trip meter
This meter display two trip meters when the ignition
switch is in the “LOCK”, “ACC” or “ON” position.
The trip meter shows the distance that the vehicle has
been driven since you last set it to zero.
To change the mode indication, briefly push the knob.
Each press of the knob changes the mode indication
alternately. To set the trip meter to zero, select the A trip or B trip
meter by pushing the knob and keep the knob pushed
for more than 2 seconds.
If you press the trip knob when the ignition switch is in
the “LOCK” position, the odometer/trip meter will light
up. It is possible to switch between the A trip meter
and B trip meter indications while the odometer/trip
meter is lit up. If you do not press the trip knob within
10 seconds of illumination of the odometer/trip meter,
the odometer/trip meter will go off. Also, if you open
and close the driver’s door within 10 seconds of illumi-
nation of the odometer/trip meter, the odometer/trip
meter will go off.
To ensure safety, do not attempt to change the
function of the indicator during driving, as an
accident could result.
UB3524AA
A trip meter
B trip meter