2005 Seat Alhambra overheating

Climate control140
the air flow from these vents can be changed vertically and
horizontally
⇒fig. 135.
The rear footwell vents
6are supplied together with vents5.K
Opening/closing vents
Vents3and 4can be opened and closed individually:
Vent closed: knurled wheel to . . . . . . .0
Vent opened: knurled wheel to . . . .
A Ad
dj
ju
us
st
t ddi
ir
re
ec
ct
ti
io
on
n oof
f aai
ir
rf
fl
lo
ow
w
Vertical – move knurled wheel
1upwards or downwards.
Horizontal – move knurled wheel
2to the left or right.K
Air vents in passenger compartment (rear)
V Ve
en
nt
t iin
n ffl
lo
oo
or
r
The vents are in the side trim on the floor of the passenger
compartment at the rear left of the vehicle. Warm air will flow out of
these vents when the interior temperature has been set to the
highest level using button
21. ”HI” will appear in the Climatronic
display.
N No
ot
te
e
Please do not use the area around the vents as stowage space as the vent
openings will be blocked and the additional heat exchanger blower will turn
off due to overheating.
Fig. 135
Fig. 136AL0-116
1
2
AL0-023


Driving153
Safety FirstControls and equipment Tips and Maintenance Technical Data
If the engine does not start, switch the glow plugs on again and try
starting it again as described.
S St
ta
ar
rt
ti
in
ng
g aa wwa
ar
rm
m een
ng
gi
in
ne
e
The glow plug lamp does not come on – the engine can be started
straight away.
K
Starting after running out of fuel
If the tank on vehicles with a diesel engine was empty, starting
after filling with diesel fuel can take longer than normal – up to
one minute. This is because the fuel system must first be freed of
air before starting.
K
S St
to
op
pp
pi
in
ng
g tth
he
e een
ng
gi
in
ne
e
Valid for all engines
C
Ca
au
ut
ti
io
on
n
When the engine has been subjected to a heavy engine load for a long
time, the engine must not be switched off abruptly. Let it idle for about 2
minutes to avoid overheating.
Valid for all versions with catalytic converter*
C Ca
au
ut
ti
io
on
n
Do not switch off the ignition while the vehicle is in motion with a gear
engaged; otherwise unburned fuel may go into the converter, where it
would burn and cause overheating, which would damage the converter.
K
A Af
ft
te
er
r tth
he
e een
ng
gi
in
ne
e hha
as
s bbe
ee
en
n sst
to
op
pp
pe
ed
d tth
he
e ffa
an
n cca
an
n cco
on
nt
ti
in
nu
ue
e rru
un
nn
ni
in
ng
g ffo
or
r aa wwh
hi
il
le
e
( (u
up
p tto
o aab
bo
ou
ut
t 110
0 mmi
in
nu
ut
te
es
s)
) wwi
it
th
h tth
he
e iig
gn
ni
it
ti
io
on
n ssw
wi
it
tc
ch
he
ed
d oof
ff
f.
. IIt
t cca
an
n aal
ls
so
o sst
ta
ar
rt
t tto
o
r ru
un
n aag
ga
ai
in
n ssu
ud
dd
de
en
nl
ly
y aaf
ft
te
er
r aa ssh
ho
or
rt
t tti
im
me
e iif
f
– – tth
he
e cco
oo
ol
la
an
nt
t tte
em
mp
pe
er
ra
at
tu
ur
re
e iin
nc
cr
re
ea
as
se
es
s ddu
ue
e tto
o hhe
ea
at
t bbu
ui
il
ld
d-
-u
up
p
– – wwh
he
en
n tth
he
e een
ng
gi
in
ne
e iis
s hho
ot
t aan
nd
d tth
he
e een
ng
gi
in
ne
e cco
om
mp
pa
ar
rt
tm
me
en
nt
t iis
s hhe
ea
at
te
ed
d
a ad
dd
di
it
ti
io
on
na
al
ll
ly
y bby
y sst
tr
ro
on
ng
g ssu
un
nl
li
ig
gh
ht
t.
.
S Sp
pe
ec
ci
ia
al
l cca
ar
re
e mmu
us
st
t tth
he
er
re
ef
fo
or
re
e bbe
e tta
ak
ke
en
n wwh
he
en
n wwo
or
rk
ki
in
ng
g iin
n tth
he
e een
ng
gi
in
ne
e
c co
om
mp
pa
ar
rt
tm
me
en
nt
t.
.
K
W WA
AR
RN
NI
IN
NG
G

158Refuelling
C
Ca
au
ut
ti
io
on
n
On vehicles with a catalytic converter, never drive until the fueltank is
completely empty. The irregular fuel supply can cause misfiring. This allows
unburnt fuel into the exhaust system, which can cause overheating and
damage to the catalyst.
K
Releasing tank flap manually
If the central locking system should fail, the flap can be released
manually:
• Open tailgate and – if fitted – fold back the right luggage
compartment trim from side panel.
• Then push the locking rod in front of the white diaphragm
housing backward slightly in direction of arrow
⇒fig. 150.K
P
Pe
et
tr
ro
ol
l
In the chapter “Technical Data” and on the inside of the tank flap
you will find information on the correct octane rating for your
engine.
K
General notes
•Unleaded petrol must comply with DIN EN1)228 and leaded
petrol with DIN 51 600.
•If, in an emergency, the octane rating of the available petrol is
lower than that required by the engine, only drive with medium
engine speeds and low engine loading. H Hi
ig
gh
h een
ng
gi
in
ne
e llo
oa
ad
di
in
ng
g wwi
it
th
h
f fu
ul
ll
l tth
hr
ro
ot
tt
tl
le
e oor
r hhi
ig
gh
h rre
ev
vs
s cca
an
n cca
au
us
se
e een
ng
gi
in
ne
e dda
am
ma
ag
ge
e.
.
Fill tank with
petrol of the correct octane rating as soon as possible.
•Fuel with a higher octane rating than that required by the engine
can be used without limitation. There are, however, no advantages
regarding output and consumption.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
Even one tankful of leaded petrol will detract from the efficiency ofthe
catalytic converter.
N No
ot
te
e
See chapter “Filling the tank”.K
1)European norm
B7M-093CFig. 150

168Your vehicle and the environment
After the running-in period
•On vehicles with a rev counter* the maximum permissible engine
speed is shown by the beginning of the red zone on the rev
counter scale. The needle of the counter must not move into this
zone.
Extremely high engine revs will be automatically governed.
K
C Cl
le
ea
an
ni
in
ng
g tth
he
e eex
xh
ha
au
us
st
t ffu
um
me
es
s
Description
T
Th
he
e ppe
er
rf
fe
ec
ct
t ffu
un
nc
ct
ti
io
on
ni
in
ng
g oof
f tth
he
e ccl
le
ea
an
ni
in
ng
g ssy
ys
st
te
em
m ffo
or
r eex
xh
ha
au
us
st
t ffu
um
me
es
s
is of great importance for the environment-friendly functioning of
your vehicle.
Therefore, keep in mind the following points:
•Versions with a catalytic converter must only use unleaded fuel
⇒"Filling the tank" chapter.
•In vehicles with a catalytic converter never drive until the fuel
tank is completely empty. Irregular fuel supply can cause misfiring,
thus allowing unburned fuel into the exhaust system which can
cause overheating and damage to the catalyst.
•If you experience starting difficulties, loss of power or engine
problems while driving, the cause could be a failure in the ignition.In this case, fuel may be entering the exhaust system without
burning and, in this way being released into the atmosphere.
Furthermore, the catalyst could deteriorate due to overheating.
Reduce speed immediately. Have this problem fixed at the nearest
Technical Service Centre.
•Do not overload the engine with oil
⇒"Engine oil" chapter.
•Do not towstartthe vehicle for more than 50 m
⇒"Tow
start/towing" chapter.
N No
ot
te
e
Even when the cleaning system for exhaust fumes is in perfect working
order, under certain circumstances, the fumes may smell like sulfur.
This depends on the percentage of sulfur in the fuel.
Often it is sufficient to change brands or buy super unleaded.
K
•D Du
ue
e tto
o ppo
os
ss
si
ib
bl
le
e hhi
ig
gh
h tte
em
mp
pe
er
ra
at
tu
ur
re
es
s oof
f tth
he
e cca
at
ta
al
ly
ys
st
t,
, ddo
o nno
ot
t ppa
ar
rk
k iin
n
p pl
la
ac
ce
es
s wwh
he
er
re
e tth
he
e cca
at
ta
al
ly
ys
st
t iis
s eea
as
si
il
ly
y eex
xp
po
os
se
ed
d tto
o iin
nf
fl
la
am
mm
ma
ab
bl
le
e mma
at
te
er
ri
ia
al
l.
.
•D
Do
o nno
ot
t uus
se
e aad
dd
di
it
ti
io
on
na
al
l ppr
ro
ot
te
ec
ct
ti
io
on
n ffo
or
r tth
he
e bbo
od
dy
y oor
r aan
nt
ti
ic
co
or
rr
ro
os
si
iv
ve
e ppr
ro
od
du
uc
ct
ts
s ffo
or
r
s su
um
mp
ps
s aan
nd
d eex
xh
ha
au
us
st
t ppi
ip
pe
es
s,
, c
ca
at
ta
al
ly
yt
ti
ic
c cco
on
nv
ve
er
rt
te
er
rs
s oor
r hhe
ea
at
t ssh
hi
ie
el
ld
ds
s.
.T
Th
he
e
a ab
bo
ov
ve
e mme
en
nt
ti
io
on
ne
ed
d mma
at
te
er
ri
ia
al
l cco
ou
ul
ld
d iig
gn
ni
it
te
e wwh
hi
il
le
e ddr
ri
iv
vi
in
ng
g.
.
W
WA
AR
RN
NI
IN
NG
G

171 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
Suggestion 6. Avoid short drives
The engine and the catalytic converter must
reach its optimum functioning temperature in order to effectively
reduce consumption and toxic gas emissions.
The fuel consumption of a cold engine of a normal vehicle right
after the start is about 30-40 liters per 100 km. After about one
kilometer the consumption decreases to 20 liters. After about
f fo
ou
ur
r
kilometers the engine has warmed up and the consumption is
normal. For this reason, it is important to avoid short drives and
heating the vehicle’s engine when the vehicle is not moving. Drive
on quickly!
The ambient temperature also counts. The illustration shows the
difference in consumption (l/100km) for the same distance (km) at
+20°C and –10°C. Your vehicle’s consumption is higher in the
summer than in the winter
⇒fig. 153.K
Suggestion 7. Check the tyre pressure
Make sure that the tyres have always adequate pressure. Even half
a bar less increases the level of fuel consumption by 5 percent. If
the pressure is not correct, the tyres wear out faster due to an
excessive deformation and overheating which, in turn, will
decrease the driving performance.
Always check the tyre pressure when the tyre is cold.
In addition, do not drive year round with winter tyres. They make
more noise and increase fuel consumption by 10 percent. Change
to summer tyres on time.
K
Suggestion 8. Avoid unnecessary weight
Apart from driving habits and periodic revisions of your vehicle,
there are other ways to reduce fuel consumption:
A Av
vo
oi
id
d uun
nn
ne
ec
ce
es
ss
sa
ar
ry
y wwe
ei
ig
gh
ht
t
Every kilogram increases fuel consumption. For this reason, it is
worth checking your boot to avoid unnecessary weight.
Frequently, the roof rack will stay on the roof even though it is no
longer needed. Due to greater air resistance, an unloaded roof
rack at a speed of 100-120 km/h increases the consumption by
approx. 12%.
K
5+20°C –10°C
15 25km
30
l/100km
B45-356PFig. 153

190Checking and refilling
C
Ca
au
ut
ti
io
on
n
• Only our G12+ (purple colour) should be used as an antifreeze additive.
Observe the notice on the container. The cooling liquid may be purchased in
Technical Services.
• The antifreeze additive G12+ can be mixed with other additives (G11 and
G12).
• The additive G12 (red colour) should never be mixed with G11.
K
Checking coolant level
The level can only be checked properly when the engine is not
running.
The coolant level must be between the
m ma
ax
xand m
mi
in
nmarks on the
expansion tank when engine is cold and can be slightly above the
m ma
ax
xmark when it is warm.K
Coolant losses
Coolant loss normally indicates leaks in the system. In this case
the cooling system should be checked by a Technical Service
Center without delay. It is not sufficient merely to add coolant.
In a sealed system losses can only occur if the boiling point of the
coolant is exceeded as a result of overheating, and coolant is
forced out of the system.
K
Topping up coolant
Switch engine off and let it cool down. Then cover expansion tank
cap with a cloth and turn cap carefully anti-clockwise and remove.
No other coolant may be used if
G G1
12
2+
+is not available. In this
case only water can be used and the correct mixture concentration
must be restored with the specified coolant additive (see previous
page) as soon as possible.
Fig. 160
N Ne
ev
ve
er
r oop
pe
en
n tth
he
e bbo
on
nn
ne
et
t iif
f yyo
ou
u cca
an
n sse
ee
e sst
te
ea
am
m oor
r cco
oo
ol
la
an
nt
t lle
ea
av
vi
in
ng
g tth
he
e een
ng
gi
in
ne
e
c co
om
mp
pa
ar
rt
tm
me
en
nt
t –– RRi
is
sk
k oof
f ssc
ca
al
ld
di
in
ng
g!
! WWa
ai
it
t uun
nt
ti
il
l nno
o mmo
or
re
e sst
te
ea
am
m oor
r cco
oo
ol
la
an
nt
t cca
an
n
b be
e sse
ee
en
n.
.
W
WA
AR
RN
NI
IN
NG
G
D Do
o nno
ot
t rre
em
mo
ov
ve
e eex
xp
pa
an
ns
si
io
on
n tta
an
nk
k cca
ap
p wwh
he
en
n een
ng
gi
in
ne
e iis
s hho
ot
t –– dda
an
ng
ge
er
r oof
f
s sc
ca
al
ld
di
in
ng
g:
:
S Sy
ys
st
te
em
m iis
s uun
nd
de
er
r ppr
re
es
ss
su
ur
re
e.
.
W
WA
AR
RN
NI
IN
NG
G

AL0-046