2005 SAAB 9-2X oil dipstick

11 - 1 0Maintenance and service
26 December 2003
Engine oil"Checking the oil levelCheck the engine oil level at each fuel stop.
1. Park the vehicle on a level surface and stop the en-
gine.
2. Pull out the dipstick, wipe it clean, and insert it
again.
3. Be sure the dipstick is correctly inserted until it
stops with the graphic symbol on its top appear-
ing as shown in the illustration.
1) Notch
2) Upper level
3) Lower level4. Pull out the dipstick again and check the oil level on
it. If it is below the lower level, add oil to bring the level
up to the upper level.!Use only engine oil with the recommended
grade and viscosity.
!Be careful not to spill engine oil when adding
it. If oil touches the exhaust pipe, it may causea bad smell, smoke, and/or a fire.
UG9032CA
1
2
3
UGB082BB
ProCarManuals.com

11 -1 3
Maintenance and service
– CONTINUED –
11
18 February 2004
Non-turbo models7. Remove the oil filter with an oil filter wrench.
8. Before installing a new oil filter, apply a thin coat of
engine oil to the seal.
9. Clean the rubber seal seating area of the bottom of
engine and install the oil filter by hand turning. Be
careful not to twist or damage the seal.
10.Tighten the oil filter by the amount indicated below
after the seal makes contact with the bottom of engine.
Please see your Saab dealer for correct oil filter infor-
mation for your vehicle.
Never over tighten the oil filter because that canresult in an oil leak.
11.Reinstall under cover (for Turbo).
12.Pour engine oil through the filler neck.Oil capacity (guideline):
4.2 US qt (4.0 liters, 3.5 Imp qt)
The oil quantity indicated above is only guideline.
The necessary quantity of oil depends on the quantity
of oil that has been drained. The quantity of drained oil
differs slightly depending on the temperature of the oil
and the time the oil is left flowing out. After refilling the
engine with oil, therefore, you must the dipstick to con-
firm that the level is correct.
13.Start the engine and make sure that no oil leaks ap-
pear around the filter’s rubber seal and drain plug.
14.Run the engine until it reaches the normal operat-
ing temperature. Then stop the engine and wait a few
minutes to allow the oil to drain back. Check the oil lev-
el again and if necessary, add more engine oil.
UGB057EA
ProCarManuals.com

11 - 2 8Maintenance and service
18 February 2004
Manual transmission oil"Checking the oil levelNon-turbo model
1) Yellow handleTurbo model
1. Park the vehicle on a level surface and stop the en-
gine.
2. Pull out the dipstick, wipe it clean, and insert it
again.
1
UG9032EB
UGB095BA
ProCarManuals.com

11 -2 9
Maintenance and service
– CONTINUED –
11
26 December 2003
1) Upper level
2) Lower level3. Pull out the dipstick again and check the oil level on
it. If it is below the lower level, add oil through the dip-
stick hole to bring the level up to the upper level."Recommended grade and viscosityEach oil manufacturer has its own base oils and addi-
tives. Never use different brands together.Oil grade:
API classification GL-5SAE viscosity No. and applicable temperature
L
F
F L
1
21
2
USB526BB
-30 -20 -10 0 10 20 30 40
-20 0 6020
80W
75W/9080 100 40
85W90
HSB036BA
ProCarManuals.com

11 - 3 2Maintenance and service
26 December 2003
el on the “COLD” range. If it is below that range, add
fluid up to the upper level. Be careful not to overfill."Recommended fluid“Dexron III” Type Automatic Transmission Fluid
Front differential gear oil (AT vehi-cles)"Checking the oil level1) Yellow handle1. Park the vehicle on a level surface and stop the en-
gine.
2. Pull out the dipstick, wipe it clean, and insert it
again.
UG9032GB
1
ProCarManuals.com

11 -3 3
Maintenance and service
– CONTINUED –
11
26 December 2003
1) Upper level
2) Lower level3. Pull out the dipstick again and check the oil level on
it. If it is below the lower level, add oil to bring the level
up to the upper level."Recommended grade and viscosityEach oil manufacturer has its own base oils and addi-
tives. Never use different brands together.Oil grade:
API classification GL-5SAE viscosity no. and applicable temperature
L
F
1
2
HSB040BB
-30 -20 -10 0 10 20 30 40
-20 0 6020
80W
75W/9080 100 40
85W90
HSB036BA
ProCarManuals.com