2005 Peugeot 307 SW Dag Owner's Manual

151Practical information-
28-02-2005
Parking the vehicle
F As far as possible, park the vehicle
on level, stable and non-slippery
ground.
F Apply the handbrake, switch off
the ignition and engage irst or
reverse gear (position P for the
automatic gearbox). Access to the spare wheel
F
Open the boot.
F Open the lap using the lug to re-
lease the winch and gain access
to its control nut.
F Unscrew the nut fully, using the
wheelbrace 1, to unroll the winch
cable.
CHANGING A WHEEL
Tools
The following tools are located:
- in the right-hand trim of the boot,
1. Wheelbrace.
2. Removable towing eye.
3. Sockets for anti-theft bolts.
- in the holder in the centre of the spare wheel,
4. Jack with handle.
5. Centralising tool.
6. Bolt cover tool.

Practical information152 -
28-02-2005
153Practical information-
28-02-2005
F Detach the wheel/holder assem-
bly from the rear of the vehicle.
F Take out the notched hook to re-
lease the wheel, as shown in the
illustration. Removing the wheel
F
Slide the holder cover to gain
access to the tools.
F If necessary, place a chock under
the wheel diagonally opposite to
the one to be changed.
F Remove the trim, using the wheel-
brace 1, pulling at the valve pas-
sage hole (for vehicles itted with
steel wheels).
F Loosen the wheel bolts (see §
"Special features of alloy wheels"
for vehicles itted with alloy wheels).
Note: you can use the other end
of the tool 6 to unscrew the wheel
bolts. F
Place the jack 4 in contact with one
of the four locating points A on the
sub-frame, the one which is clos-
est to the wheel to be changed.
F Extend the jack 4 until its base is
in contact with the ground. Ensure
that the centre line of the base of
the jack is straight above the lo-
cating point A used.
F Raise the vehicle
F Remove one bolt and install the
centralising tool 5 in its place.
F Unscrew the other bolts and
remove the wheel.

Practical information152 -
28-02-2005
153Practical information-
28-02-2005
Fitting a wheel
F Position the wheel using the
centralising tool 5 to assist you.
F Tighten the bolts by hand and
remove the centralising tool 5.
F Partly tighten the bolts using the
wheelbrace 1.
F Fold the jack 4 and remove it.
F Fully tighten the bolts using the
wheelbrace 1.
F Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.
F Put the corresponding tools in the
holder and secure its cover.
F Place the holder on the ground
and align the spare wheel on it.
F Pass the notched hook into the
holder cover.
F Reit the wheel under the vehicle
tightening the winch control nut
using the wheelbrace 1.
F Fully tighten and check that
the wheel is horizontally lush
against the rear loor .
F Close the lap using the lug to lock
the winch.
F Store the rest of the tools in the
right-hand trim of the boot. For your safety, always
change the wheel:
-
on level, stable, non-slippery ground,- with the handbrake on and the igni- tion switched off,
-
with irst or reverse gear engaged (po-
sition P for the automatic gearbox),
- with the vehicle chocked.
Never go underneath a vehicle
that is supported only by a jack
(use a ramp).
Never reit the holder under the
vehicle without the spare wheel.
Do not use a screwdriver in place
of the wheelbrace to unwind or
wind the winch. Recommendations when using
the temporary spare wheel*
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, have it replaced as quickly
as possible.
Observe the following instructions in
order to avoid altering the behaviour
of the vehicle:
- do not exceed
50 mph (80 km/h) ,
- do not it a wheel trim,
- drive with care,
- check the tyre pressure indicated on the label.
* According to model and country.
After changing the wheel:
- have the correct positioning of the
punctured wheel, the tightening
of the bolts and the tyre pressure
checked by a PEUGEOT dealer as
soon as possible,
- have the punctured tyre repaired and reit it to the vehicle as soon as
possible,
-
have the correct positioning of the
spare wheel checked by a PEUGEOT
dealer.

Practical information154 -
28-02-2005
155Practical information-
28-02-2005
Special features of alloy
wheels
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool 6 to remove the
trims before slackening the bolts. Fitting the spare wheel
If your vehicle is itted with a steel
spare wheel, when itting it, it is
normal
when tightening the bolts to
notice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
Anti-theft bolts
If your wheels are fitted with an anti-
theft bolt (one per wheel), the chrome
trim and then the plastic cover must
be removed using
yellow tool 6,
before unscrewing the bolt using one
of the two anti-theft sockets and the
wheelbrace.
Note:
these two anti-theft sockets
were given to you on delivery of your
vehicle along with the duplicate keys
and the confidential card. M
ake a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain duplicate sockets from a
PEUGEOT dealer.
Fitting snow tyres
If you it snow tyres mounted on steel
wheels onto your vehicle, it is
es-
sential to use special bolts available
from your PEUGEOT dealer.

Practical information154 -
28-02-2005
155Practical information-
28-02-2005
F Turn the protective cover corre-
sponding to the faulty bulb a quarter
of a turn to the left and remove it.
F Disconnect the connector.
F Press the end of the securing clip
to free it. Change the bulb.
When itting the new bulb, ensure
that the direction notches are po-
sitioned correctly and the secur-
ing clip is ixed properly.
F Reconnect the connector.
F Reit the protective cover, posi-
tioning it with the arrow upwards,
then turn it a quarter of a turn to
the right.
The headlamps are itted with poly-
carbonate glass with a protective
coating. Do not clean them with a
dry or abrasive cloth, nor with a
detergent or solvent product. Use
a sponge and soapy water. 4. Side lights (W 5 W).
F
Pull the socket rearwards, remove
the bulb and change it.
5. Direction indicators (PY 21 W amber).
F Turn the bulb holder a quarter of a
turn and remove it.
F Change the bulb.
Note: in certain climatic conditions
(low temperature, humidity), conden-
sation inside the headlamp glass is
normal ; it disappears a few minutes
after the lights are switched on.
CHANGING A BULB
Front lights
Handle the bulbs with a dry cloth.
1. Dipped beam headlamps (H7-55 W).
2. Main beam headlamps (H1-55 W).
3. Front fog lamps (H1-55 W).

Practical information156 -
28-02-2005
157Practical information-
28-02-2005
Direction indicator side repeaters
(WY 5 W amber).
F Push the repeater forwards and
release the assembly.
F Hold the connector and turn the
lens a quarter of a turn.
F Change the bulb.
Amber coloured bulbs (di-
rection indicators and side
repeaters), must be re-
placed with bulbs of identi-
cal speciication and colour.Rear lights
1. Brake lights (P 21 W).
2. Side lights (R 5 W).
3. Direction indicators (P 21 W).
4. Reversing light (P 21 W), right side.
Fog lamp (P 21 W), left side.
These 5 bulbs are changed by
removing the light:
F Remove the corresponding boot
side trim to access the light,
F Remove the light ixing nut inside
the boot,
F Remove the light ixing nut out-
side the boot,
F Remove the light,
F Unclip the harness, F
Remove the bulb holder pressing
on the tabs A,
F Change the faulty bulb.
Note: if necessary, use the wheel-
brace to remove the nuts.
When reitting, take care to position
the bulb holder and the light cor-
rectly.
Number plate lights (W 5 W)
F Insert a thin screwdriver into one
of the external holes of the lens.
F Push it outwards to unclip it.
F Remove the lens.
F Change the faulty bulb.

Practical information156 -
28-02-2005
157Practical information-
28-02-2005
Direction indicator side repeaters
(WY 5 W amber).
F Push the repeater forwards and
release the assembly.
F Hold the connector and turn the
lens a quarter of a turn.
F Change the bulb.
Amber coloured bulbs (di-
rection indicators and side
repeaters), must be re-
placed with bulbs of identi-
cal speciication and colour.Rear lights
1. Brake lights (P 21 W).
2. Side lights (R 5 W).
3. Direction indicators (P 21 W).
4. Reversing light (P 21 W), right side.
Fog lamp (P 21 W), left side.
These 5 bulbs are changed by
removing the light:
F Remove the corresponding boot
side trim to access the light,
F Remove the light ixing nut inside
the boot,
F Remove the light ixing nut out-
side the boot,
F Remove the light,
F Unclip the harness, F
Remove the bulb holder pressing
on the tabs A,
F Change the faulty bulb.
Note: if necessary, use the wheel-
brace to remove the nuts.
When reitting, take care to position
the bulb holder and the light cor-
rectly.
Number plate lights (W 5 W)
F Insert a thin screwdriver into one
of the external holes of the lens.
F Push it outwards to unclip it.
F Remove the lens.
F Change the faulty bulb.

Practical information156 -
28-02-2005
157Practical information-
28-02-2005
Third brake light:
4 W 5 W bulbs.
F Remove the tailgate upper trim
carefully by unclipping it on either
side, perpendicular to its direction
of engagement.
F Insert a screwdriver into the two
outer holes B to press on the two
tabs C.
F Push the light unit outwards while
maintaining the pressure on the
tabs.
F Pull the light unit outwards while
tilting it.
F Change the faulty bulb.
F When reitting, ensure that the
light unit tabs are engaged cor-
rectly and that the tailgate upper
trim has been put back in place
correctly.