2005 NISSAN X-TRAIL sunroof

LT-132
INTERIOR ROOM LAMP

INTERIOR ROOM LAMPPFP:26410
System DescriptionEKS003BQ
POWER SUPPLY AND GROUND
Power is supplied at all times

through 10A fuse [No. 28, located in fuse block (J/B)]

to key switch terminal 1, and

to time control unit terminal 1,

through 10A fuse [No. 26, located in fuse block (J/B)]

to interior room lamp terminal 1

to luggage room lamp terminal 1, and

to map lamp terminal 1 (with sunroof).
When the key is removed from ignition key cylinder, power is interrupted

through key switch terminal 2

to time control unit terminal 18.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 5, located in fuse block (J/B)]

to time control unit terminal 17.
Ground is supplied

to time control unit terminal 16

through grounds M27 and M70.
When the driver’s door is opened, ground is supplied

to time control unit terminal 30

through front door switch (driver side) terminal 2

through front door switch (driver side) terminal 3

through grounds B8 and B18.
When the door (except driver’s door) is opened, ground is supplied

to time control unit terminal 31

through front door switch (passenger side) terminal 1

through case ground of front door switch (passenger side),

through rear door switch LH and RH terminal 1

through case ground of rear door switch LH and RH, and

through back door switch terminal 1

through back door switch terminal 3

through ground D53.
When the driver’s door is unlocked, the time control unit receives a ground signal

to time control unit terminal 28

through front door lock actuator (driver side) terminal 5

through front door lock actuator (driver side) terminal 2

through grounds M27 and M70.
When a signal, or combination of signals is received by the time control unit, ground is supplied

to interior room lamp terminal 2, and

to map lamp terminal 3 (with sunroof)

through time control unit terminal 26.
With power and ground supplied, the interior room lamp and map lamp (with sunroof) illuminates.
SWITCH OPERATION
When interior room lamp switch is ON, ground is supplied

to interior room lamp

through case grounds of interior room lamp.

INTERIOR ROOM LAMP
LT-133
C
D
E
F
G
H
I
J
L
MA
B
LT

When map lamp switch is ON, ground is supplied (with sunroof)

to map lamp terminal 2

through ground M27 and M70.
INTERIOR ROOM LAMP TIMER OPERATION
When interior room lamp and map lamp (with sunroof) switch is in the DOOR position, the time control unit
keeps the interior room lamp and map lamp (with sunroof) illuminated for about 30 seconds when

unlock signal is supplied from driver's door unlock sensor while all doors are closed and key is out of igni-
tion key cylinder

key is removed from ignition key cylinder while all doors are closed

driver's door is opened and then closed while key is out of the ignition key cylinder. (However, if the
driver's door is closed with the key inserted in the ignition key cylinder after the driver's door is opened
with the key removed, the timer is operated.)
The timer is canceled when

driver's door is locked,

driver's door is opened, or

ignition switch is turned ON.
ON-OFF CONTROL
When the driver’s door, passenger’s door, rear LH door or rear RH door is opened, the interior room lamp and
map lamp (with sunroof) turns on while the interior room lamp and map lamp (with sunroof) switch is in the
DOOR position.

LT-150
INTERIOR LAMP

Bulb ReplacementEKS00OMA
MAP LAMP (WITHOUT SUNROOF)
1. Remove the lens using a clip driver or a suitable tool.
2. Remove the shade mounting screw and remove the shade from
the map lamp.
3. Remove the bulb.
4. Installation is the reverse order of removal.
MAP LAMP (WITH SUNROOF)
1. Remove the lens using a clip driver or a suitable tool.
2. Remove the bulb.
3. Installation is the reverse order of removal.
READ LAMP
1. Remove the read lamp. Refer to LT- 1 5 0 , "Removal and Installa-
tion" .
2. Remove the lens mounting screw.
3. Release four clips and remove the lens.
4. Remove the bulb.
Removal and InstallationEKS00OMB
REMOVAL
Map Lamp (Without sunroof)
1. Using a clips driver or a suitable tool, press and remove the
metal clip of the map lamp.
2. Disconnect the map lamp connector.Map lamp (Without sunroof) : 12V - 8W
PKIA5761E
Map lamp (Without sunroof) : 12V - 10W
SKIA0065E
Read lamp : 12V - 8W
PKIC1036E
PKIA0472E

INTERIOR LAMP
LT-151
C
D
E
F
G
H
I
J
L
MA
B
LT

Map Lamp (With sunroof)
1. Using a clips driver or a suitable tool, press and remove the
metal clip of the map lamp.
2. Disconnect the map lamp connector.
Read Lamp
1. Take out the read lamp while pushing the metal clip using a clip
remover.
2. Disconnect the connector to release the read lamp.
INSTALLATION
Installation is the reverse order of removal.
SKIA0066E
PKIC1037E

LT-152
BULB SPECIFICATIONS

BULB SPECIFICATIONSPFP:26297
HeadlampEKS003GS
Exterior LampEKS003GT
Interior Lamp/IlluminationEKS003GU
Item Wattage (W)
Xenon typeLow 35 (D2R)
High 55 (H1)
Conventional type High/Low 60/55 (H4)
Driving lamp65 (H1R1)
Item Wattage (W)
Front combination lamp Clearance lamp 5
Front turn signal lamp21 (amber)
Side turn signal lamp5
Fog lampFront fog lamp 55 (H11)
Rear fog lamp 21
Rear combination lampStop/Tail lamp 21/5
Rear turn signal lamp 21
Back-up lamp 21
License plate lamp5
High-mounted stop lamp5
Item Wattage (W)
Interior room lamp10
Map lampWithout sunroof 8
With sunroof 10
Luggage room lamp10
Ste p lamp2.7
Ashtray illumination lamp1.4

HARNESS
PG-67
C
D
E
F
G
H
I
J
L
MA
B
PG

NATS BL Nissan Anti-Theft System
NAVI AV Navigation System
NONDTC AT Non-Detective Items
OVRCSV AT Overrun Clutch Solenoid Valve
P/SCKT WW Power Socket
PGC/V EC EVAP Canister Purge Volume Control Solenoid Valve
PHASE EC Camshaft Position Sensor (PHASE)
PHONE AV Telephone (Pre-wire)
PNP/SW AT Park/Neutral Position Switch
PNP/SW EC Park/Neutral Position Switch
PNPSW1 EC Park/Neutral Position Switch
POS EC Crankshaft Position Sensor (CKPS) (POS)
POWER PG Power Supply Routing
PRGVLV EC EVAP Canister Purge Volume Control Solenoid Valve
PRWIRE BL Theft Warning System (Pre-wire)
PS/SEN EC Power Steering Pressure Sensor
PST/SW EC Power Steering Oil Pressure Switch
R/FOG LT Rear Fog Lamp
ROOM/L LT Interior Room Lamp
RP/SEN EC Refrigerant Pressure Sensor
RRO2 EC Rear Heated Oxygen Sensor
RRO2/H EC Rear Heated Oxygen Sensor Heater
S/LOCK BL Power Door Lock - Super Lock
S/SIG EC Start Signal
S/WARN SB Seat Belt Warning System
SEAT SE Power Seat
SEN/PW EC Sensor Power Supply
SHIFT AT A/T Shift Lock System
SROOF RF Sunroof
SRS SRS Supplemental Restraint System
SSV/A AT Shift Solenoid Valve A
SSV/B AT Shift Solenoid Valve B
START SC Starting System
STEP/L LT Step Lamp
STOP/L LT Stop Lamp
TAIL/L LT Parking, License and Tail Lamps
TCC/V EC Turbocharger Boost Control Solenoid Valve
TCCSV EC Turbocharger Boost Control Solenoid Valve
TCV AT Torque Converter Clutch Solenoid Valve
TPS AT Throttle Position Sensor
TPS1 EC Throttle Position Sensor (Sensor 1)
TPS2 EC Throttle Position Sensor (Sensor 2)
TPS3 EC Throttle Position Sensor
TURN LT Turn Signal and Hazard Warning LampCode Section Wiring Diagram Name

MA-4
DESCRIPTION

DESCRIPTIONPFP:00000
Pre-Delivery Inspection ItemsELS000Y5
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
Install vehicle protection kit
Fit all accessories ordered (if applicable) (e.g. towbar, audio, navigation, air conditioner, styling kit)
UNDER HOOD — engine off
Check coolant level and cooling system for leaks
Charge battery and check terminals for condition
Check drive belts tension (diesel only)
Check fuel filter for water or dust (diesel only) and fuel system for leaks
Check engine oil level and for oil leaks
Check brake and clutch fluid levels and fluid lines for leaks
Check and top up washer reservoirs
Check power steering fluid level and fluid lines for leaks (if applicable)
Check air conditioning system for gas leaks (if applicable)
ON INSIDE AND OUTSIDE
Install transit fuse if removed for vehicle storage
Check instruments, gauges, lamps, horn and accessories for operation
Check wipers and washers for operation and adjustment
Check interior and door mirrors and sun visors for operation
Set radio code and set clock
Check parking brake adjustment
Check clutch pedal adjustment
Check steering lock operation
Check seat adjusters and seat belts for operation
Check all windows for operation and alignment
Check mouldings, trim and fittings for fit and alignment
Check weatherstrips for fit and adhesion
Check hood, trunk lid, door panels and fuel lid for fit and alignment
Check latches, keys, remote key, door locks and remote trunk lid and fuel lid release for operation
Check wheel nut torques
Check tyre pressure (incl. spare tyre)
Check tool kit and jack for operation
Check automatic transmission/transaxle starter inhibitor (if applicable)
Check sunroof for operation and alignment (if applicable)
UNDER BODY
Check manual transmission/transaxle, differential and transfer box for oil level and oil leaks
Tighten bolts and nuts steering linkage and gear box, axle/suspension parts, propeller and exhaust system
Check brake and clutch lines, and oil/fluid reservoirs for leaks
Remove front suspension spacer blocks (if applicable)
Check body mounting torque (if applicable)

MA-48
CHASSIS AND BODY MAINTENANCE

Checking Body CorrosionELS000C0
Visually check body panels for collision damage (scratches, chipping, rubbing, etc.) or damage to the anti-cor-
rosion materials. In particular, check the following locations.
HEMMED PANELS
Hood front end, door lower end, trunk lid rear end, etc.
PANEL JOINT
Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut tower in engine com-
partment, etc.
PANEL EDGE
Trunk lid opening, sunroof opening, fender wheel-arch flange, fuel filler lid flange, around holes in panel, etc.
PARTS CONTACT
Waist moulding, windshield moulding, bumper, etc.
PROTECTORS
Damage or condition of mudguard, fender protector, chipping protector, etc.
ANTI-CORROSION MATERIALS
Damage or separation of anti-corrosion materials under the body.
DRAIN HOLES
Condition of drain holes at door and side sill. When repairing corroded areas, refer to the Corrosion Repair
Manual.