2005 MITSUBISHI 380 key

SWS DIAGNOSIS
SIMPLIFIED WIRING SYSTEM (SWS)54B-24
SUNROOF
PULSE CHECK
M1549015100562
1. The input signals (signals other than SWS
communication line signals), which are
compatible with the SWS monitor by using the
diagnostic tool MB991958 (MUT-III Sub
Assembly) or voltmeter, can be confirmed by the
Pulse Check.2. Use the diagnostic tool MB991958 (MUT-III Sub
Assembly) or voltmeter to check the following
input signals.
NOTE: If a problem is found in the Pulse Check,
refer to Input Signal Chart P.54B-61.
Switches and their conditions, which are applicable
for Pulse CheckITEM ITEM NO. INPUT SIGNAL DISPLAY ON
DIAGNOSTIC TOOLNORMAL CONDITION
SUNROOF
OPE.30 Ignition switch
(IG1)IG SW (IG1) (ETACS ECU) ON
72 Response by the
sunroof-ECUS/R ECU ACK (SUNROOF
ECU)INPUT CHECK (only
momentarily when switch is
operated)
INPUT SIGNAL REQUIREMENTS FOR SOUNDING TONE
ALARM
Key reminder switch When the ignition key is pulled out
Hazard warning lamp switch When the switch is turned from off to on
Door switches A door is opened when all the doors are
closed
Door lock key cylinder switch When a door is locked or unlocked by a key
cylinder
Door lock actuators Move the door lock knob from lock position
to unlock position or vice versa
Door lock switch (incorporated in the power window main
switch and front power window sub switch)When a door is locked or unlocked by a door
lock switch
Keyless entry transmitter When the switch is turned from off to on
Interior lamp loaded signal Illuminates the interior lamps

SYMPTOM CHART
SIMPLIFIED WIRING SYSTEM (SWS)54B-57
SYMPTOM CHARTM1549000801159
ECU COMMUNICATION SYSTEM
FUNCTION SYSTEM
SYMPTOM INSPECTION
PROCEDUREREFERENCE
PA G E
Communication with the SWS monitor kit is not possible. A-1
P.54B-63
Communication with the column switch (column-ECU) is not possible. A-2
P.54B-68
Communication with the ETACS-ECU is not possible. A-3
P.54B-74
Communication with the front-ECU is not possible. A-4
P.54B-80
Communication with the sunroof-ECU is not possible. A-5
P.54B-87
SYSTEM SYMPTOM INSPECTION
PROCEDUREREFERENCE
PA G E
Tone alarm General description concerning the tone alarm
P.54B-94
Light reminder tone alarm function does not work
normally.B-2
P.54B-98
Seat belt tone alarm function does not work
normally.B-3
P.54B-101
Door ajar warning buzzer function does not work
normally.B-4
P.54B-106
The multi center display does not sound normally
when it is operated. B-5
P.54B-112
Turn-signal lamp buzzer function does not work
normally.B-6
P.54B-116
Central door locking
systemGeneral description concerning central door
locking system
P.54B-118
The central door locking system does not work at
all.C-1
P.54B-122
Some doors do not lock or unlock. C-2
P.54B-129
All the doors do not lock or unlock with just the
door lock switch operation.C-3
P.54B-142
All the doors do not lock or unlock with just the
door lock key cylinder key operation.C-4
P.54B-143
Forgotten key prevention function does not work
normally.C-5
P.54B-144

SYMPTOM CHART
SIMPLIFIED WIRING SYSTEM (SWS)54B-58
Power windows General description concerning the power
windowsP.54B-148
Power windows do not work at all. D-1
P.54B-151
The power window timer function does not work
normally.D-2
P.54B-161
Only the front door window (LH) does not work by
operating power window main switch.D-3
P.54B-164
Power windows do not work normally by operating
the front passenger's or rear passenger's sub
switches.D-4
P.54B-167
Front or rear passenger's power windows do not
work at all by operating the power window main
switch.D-5
P.54B-187
Keyless entry system General description concerning the keyless entry
system
P.54B-187
Keyless entry system does not operate. E-1
P.54B-191
The dome lamp, the turn-signal lamps and the
horn do not operate through the answerback
function.E-2
P.54B-193
Encrypted code cannot be registered. E-3
P.54B-202
The trunk is not opened when the keyless entry
transmitter "TRUNK" button is operated.E-4
P.54B-205
Sunroof General description concerning the sunroof
P.54B-209
Sunroof does not operate. F-1
P.54B-210
Any of the sunroof switch positions is defective. F-2
P.54B-219
Sunroof timer function does not work normally. F-3
P.54B-220
Windshield wiper and
washerGeneral description concerning the windshield
wiper and washer
P.54B-223
The windshield wiper do not work at all. G-1
P.54B-226
The windshield wipers do not work when the
windshield wiper switch is at "INT" or "MIST"
position or the windshield washer switch is at "ON"
position. However, the wipers work at low speed
when the windshield wiper switch is at "LO" or "HI."G-2
P.54B-234
All of the windshield wiper switch positions are
defective.G-3
P.54B-236
Windshield wipers does not stop at the
predetermined park position.G-4
P.54B-240
The windshield intermittent wiper interval cannot
be adjusted by using the variable intermittent wiper
control switch.G-5
P.54B-246
The windshield intermittent wiper interval is not
changed according to the vehicle speed.G-6
P.54B-248
The windshield washer does not work. G-7
P.54B-251 SYSTEM SYMPTOM INSPECTION
PROCEDUREREFERENCE
PA G E

SYMPTOM CHART
SIMPLIFIED WIRING SYSTEM (SWS)54B-60
Interior lamp General description concerning the interior lampP.54B-355
The dome lamp do not illuminate and go out
normally.K-1
P.54B-359
The front dome lamp, rear dome lamp or trunk
lamp do not illuminate or go out normally.K-2
P.54B-366
Dome lamp dimming function does not work
normally.K-3
P.54B-376
The ignition key hole illumination lamp does not
illuminate or go out normally.K-4
P.54B-381
The interior lamp automatic shutoff function does
not work normally.K-5
P.54B-389
The door ajar indicator lamps do not illuminate or
go out normallyK-6
P.54B-394
The seat belt warning lamp do not illuminate or go
out normallyK-7
P.54B-398
Can not customize the functions by operating the multi center display . L-1
P.54B-402 SYSTEM SYMPTOM INSPECTION
PROCEDUREREFERENCE
PA G E

INPUT SIGNAL CHART
SIMPLIFIED WIRING SYSTEM (SWS)54B-62
DIAGNOSTIC TOOL OR VOLTMETER
If a problem is found in the Pulse Check, observe the
table below.
SYMPTOM INSPECTION
PROCEDUREREFERENCE
PA G E
ETACS-ECU does not receive any signal from the key reminder switch. N-1
P.54B-432
ETACS-ECU does not receive any signal from the hazard warning lamp
switch.N-2
P.54B-436
ETACS-ECU does not receive any signal from any of the door switches. N-3
P.54B-440
ETACS-ECU does not receive any signal from the door lock key cylinder
switch.N-4
P.54B-446
ETACS-ECU does not receive any signal from the front door lock actuator. N-5
P.54B-451
ETACS-ECU does not receive any signal from the door lock switch
(incorporated in the power window main switch and front power window
sub switch).N-6
P.54B-460
ETACS-ECU does not receive any signal from the trunk lid latch assembly. N-7
P.54B-469
Transmitter ETACS-ECU does not receive any signal from the lock,
unlock, trunk or panic switch.N-8
P.54B-472
ETACS-ECU does not receive any interior lamp loaded signal. N-9
P.54B-474

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-95
Light reminder tone alarm function
When the taillights or headlamps is the ON position, if the igni-
tion key is removed and the driver's door is opened, a tone
alarm will sound continuously to warn that the lamps are on.
However, if the taillights or headlamps have been turned off by
the headlamp automatic-shutoff function, the tone alarm will not
sound.
Seat belt tone alarm function

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-98
54B
INSPECTION PROCEDURE B-2: Tone Alarm: Light Reminder Tone Alarm Function does not Work
Normally.
NOTE: This troubleshooting procedure requires the
use of diagnostic tool MB991958 and SWS monitor
kit MB991813. For details on how to use the SWS
monitor, refer to "How to connect SWS monitor
P.54B-13."
.
CIRCUIT OPERATION
The ETACS-ECU operates the light reminder tone
alarm function according to the following signals:
Ignition switch (IG1): OFF
Ignition key reminder switch: ON
Front door switch (RH): ON
Taillamp switch: ON
Headlamp switch: ON
The ETACS-ECU operates the lamp reminder tone
alarm function under the following conditions:
Ignition switch: "LOCK" (OFF) position
Ignition key: Removed from the ignition key cylin-
der
Driver’s door: open
Taillamps or headlamps: ON
.
TECHNICAL DESCRIPTION (COMMENT)
If the function does not work normally, the input cir-
cuit system from the switches or the ETACS-ECU
may be defective (refer to "CIRCUIT OPERATION").
.
TROUBLESHOOTING HINTS
Trouble in input signal system
The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
The ETACS-ECU may be defective
Refer to circuit diagrams GROUP-90
Refer to configuration diagrams GROUP-80
DIAGNOSIS
Required Special Tools:
MB991223: Harness Set
MB991958: diagnostic tool (MUT-III Sub Assembly)
MB991824: Vehicle Communication Interface (V.C.I.)
MB991827: MUT-III USB Cable
MB991910: MUT-III Main Harness A
MB991813: SWS Monitor Kit
MB991806: SWS Monitor Cartridge

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-100
STEP 2. Check the input signal by using "FUNCTION
DIAG." menu of the SWS monitor.
Check the input signals from the following switches:
Ignition switch: OFF (key removed)
Lighting switch: TAIL or HEAD
Driver’s door: open
Front passenger's door: closed
(1) Operate diagnostic tool MB991958 according to the
procedure below to display "LGT MONI. ALRM."
a. Select "Interactive Diagnosis."
b. Select "System Select."
c. Select "SWS."
d. Select "SWS MONITOR."
e. Select "Function Diag."
f. Select "BUZZER."
g. Select "LGT MONI. ALRM."
(2) Check that normal conditions are displayed for the items
described in the table below.
NOTE: diagnostic tool MB991958 display changes when
the driver's or the front passenger's door is opened. If any of
the doors is open, the system cannot be checked correctly.
Q: Does diagnostic tool MB991958 display "HEADLAMP
SW", "TAILLAMP SW", "IG SW IG1", "FRONT DOOR
SW", "H/L AUTO-CUT" and "BUZZER" as normal
condition?
Normal conditions are displayed for all the items :
Replace the ETACS-ECU. The lamp reminder tone
alarm function should now work normally.
Normal condition is not displayed for "HEADLIGHT SW"
: Refer to Inspection Procedure M-5 "ETACS-ECU
does not receive any signal from the headlamp switch
P.54B-420."
Normal condition is not displayed for "TAILLIGHT SW" :
Refer to Inspection Procedure M-5 "ETACS-ECU
does not receive any signal from the taillamp switch
P.54B-420."
Normal condition is not displayed for "IG SW (IG1)" :
Refer to Inspection Procedure M-2 "ETACS-ECU
does not receive any signal from the ignition switch
(IG1) P.54B-408." ITEM NO. ITEM NAME NORMAL CONDITION
ITEM 00 HEADLAMP SW Either of items is ON
ITEM 01 TAILLAMP SW
ITEM 30 IG SW IG1 OFF
ITEM 32 FRONT DOOR SW ON
ITEM 35 H/L AUTO-CUT OFF
ITEM 43 BUZZER ON