2005 MITSUBISHI 380 Exhaust

INTAKE MANIFOLD PLENUM
INTAKE AND EXHAUST15-6
Required Special Tool:
MD998412: Guide
INSTALLATION SERVICE POINT
.
>>A<< INTAKE MANIFOLD PLENUM INSTALLA-
TION
Use special tool MD998412 to install the intake manifold ple-
num.
REMOVAL STEPS
1. MANIFOLD ABSOLUTE
PRESSURE SENSOR
CONNECTOR
2. CONTROL WIRING HARNESS
AND INJECTOR WIRING
HARNESS COMBINATION
CONNECTOR
3. CRANKSHAFT POSITION
SENSOR CONNECTOR
4. KNOCK SENSOR CONNECTOR
5. POWER STEERING PRESSURE
SWITCH CONNECTOR
6. EVAPORATIVE EMISSION
PURGE SOLENOID CONNECTOR
8. VACUUM HOSE CONNECTION
9. PURGE HOSE
10. POWER STEERING PRESSURE
HOSE CLAMP
11. POWER STEERING PRESSURE
HOSE CLAMP BRACKET
12. INTAKE MANIFOLD PLENUM
STAY, REARSTEERING GEAR AND LINKAGE
PROTECTOR (REFER TO 37,
STEERING GEAR BOX AND
LINKAGE P.37-30)
POWER STEERING OIL PUMP
(REFER TO 37, POWER
STEERING OIL PUMP ASSEMBLY
P.37-43)
15. POWER STEERING OIL PUMP
BRACKET CONNECTING BOLT
16. INTAKE MANIFOLD PLENUM
STAY, FRONT
>>A<<17. INTAKE MANIFOLD PLENUM
18. INTAKE MANIFOLD PLENUM
GASKET
19. VACUUM PIPE
20. EVAPORATIVE EMISSION
PURGE SOLENOID ASSEMBLY
23. HARNESS BRACKET
24. MANIFOLD ABSOLUTE
PRESSURE SENSOR
25. O-RINGREMOVAL STEPS (Continued)

INTAKE MANIFOLD
INTAKE AND EXHAUST15-7
INTAKE MANIFOLD
REMOVAL AND INSTALLATION M1151003000802
Pre-removal Operation
Fuel Discharge Prevention [Refer to GROUP 13B,
On-vehicle Service
Fuel Pump Relay Disconnection
(How to Reduce Pressurized Fuel Lines) 13A-663.]
Intake Manifold Plenum Removal (Refer to P.15-5.)Post-installation Operation
Intake Manifold Plenum Installation (Refer to P.15-5.)
Fuel Leakage Inspection
REMOVAL STEPS
1. INJECTOR CONNECTOR
2. ENGINE MOUNTING STAY
>>C<<3. FUEL HIGH-PRESSURE HOSE
CONNECTION
5. BLOW-BY HOSE
<>6. FUEL RAIL AND INJECTOR
7. PCV HOSE CONNECTION8. TIMING BELT FRONT UPPER
COVER, RIGHT
9. TIMING BELT FRONT UPPER
COVER, LEFT
10. WATER PUMP BRACKET>>B<<11. INTAKE MANIFOLD
>>A<<12. INTAKE MANIFOLD GASKET
13. CONTROL HARNESS CLAMPREMOVAL STEPS (Continued)

INTAKE MANIFOLD
INTAKE AND EXHAUST15-8
REMOVAL SERVICE POINT
.
<> FUEL RAIL AND INJECTOR REMOVAL
Care must be taken when removing the fuel rail not to drop
the injector.
Remove the fuel rail with the injectors attached to it.
INSTALLATION SERVICE POINTS
.
>>A<< INTAKE MANIFOLD GASKET INSTALLA-
TION
Install the gasket with the protrusions in the position illustrated.
.
>>B<< INTAKE MANIFOLD INSTALLATION
1. Coat the intake manifold mounting studs with engine oil.
2. Tighten the intake manifold mounting nuts by the following
procedure.
.
ORDER MOUNTING NUTS TIGHTENING TORQUE
1st Right-bank nuts 6.5
1.5 Nm (58 13 in-lb)
2nd Left-bank nuts 22
1 Nm (16 1 ft-lb)
3rd Right-bank nuts 22
1 Nm (16 1 ft-lb)
4th Left-bank nuts 22
1 Nm (16 1 ft-lb)
5th Right-bank nuts 22
1 Nm (16 1 ft-lb)

INTAKE MANIFOLD
INTAKE AND EXHAUST15-9
>>C<< FUEL HIGH-PRESSURE HOSE
INSTALLATION
Be careful not to allow any engine oil to enter the fuel
rail.
Be careful not to bend the fuel high-pressure hose as it
is made of plastics.
1. When connecting the fuel high-pressure hose to the fuel rail,
apply a small amount of new engine oil to the O-ring and
then insert the fuel high-pressure hose, being careful not to
damage the O-ring.
2. While turning the fuel high-pressure hose to the left and
right, install it to the fuel rail.
3. Check that the injector turns smoothly. If it does not turn
smoothly, the O-ring may be trapped. Remove the fuel
high-pressure hose and then re-insert it into the fuel rail and
check again.
INSPECTIONM1151003100672
Check the following points; replace the part if a problem is
found.
.
Intake Manifold Check
1. Check for damage or cracking of any part.
2. Clogging of the negative pressure (vacuum) outlet port.
3. Using a straight edge and feeler gauge, check for distortion
of the cylinder head installation surface.
Standard value: 0.15 mm (0.006 inch) or less
Limit: 0.20 mm (0.008 inch)

EXHAUST MANIFOLD
INTAKE AND EXHAUST15-10
EXHAUST MANIFOLD
REMOVAL AND INSTALLATION M1151003301055

Pre-removal and Post-installation Operation
Under Cover Removal and Installation (Refer to GROUP
51, Under Cover P.51-13).
Air Duct Removal and Installation (Refer to P.15-4).
REMOVAL STEPS
1. LEFT HEATED OXYGEN SENSOR
CONNECTOR
<> >>A<<2. LEFT BANK HEATED OXYGEN
SENSOR (FRONT)
<> >>B<<3. LEFT BANK HEATED OXYGEN
SENSOR (REAR)
4. HEAT PROTECTOR
5. FRONT EXHAUST PIPE
CONNECTING BOLTS6. FRONT EXHAUST PIPE GASKET
7. EXHAUST MANIFOLD STAY, LEFT
B
8. EXHAUST MANIFOLD
9. EXHAUST MANIFOLD GASKET
10. EXHAUST MANIFOLD STAY, LEFT
A REMOVAL STEPS (Continued)