2005 MERCEDES-BENZ SPRINTER service schedule

Full synthetic oils, such as Mobilt1 0W-40, is
required if the ASSYST Oil Service Reminder is fol-
lowed. Use of a lower quality oil on this service
schedule may cause severe engine damage.
DESCRIPTION - AUTOMATIC TRANSMISSION
FLUID - NAG1
NOTE: Refer to Service Procedures in this group for
fluid level checking procedures.
Shellt3403 Automatic Transmission Fluid is the
recommended fluid for the NAG1 DaimlerChrysler
automatic transmission.
Dexron II fluid IS NOT recommended. Clutch
chatter can result from the use of improper
fluid.
MopartATF+4, Automatic Transmission Fluid, or
other fluids meeting MS-9602, may be used if Shellt
3403 Automatic Transmission Fluid is not available.
Shellt3403 Automatic Transmission Fluid when
new is red in color. The ATF is dyed red so it can be
identified from other fluids used in the vehicle such
as engine oil or antifreeze. The red color is not per-
manent and is not an indicator of fluid condition. As
the vehicle is driven, the ATF will begin to look
darker in color and may eventually become brown.
This is normal.
FLUID ADDITIVES
DaimlerChrysler strongly recommends against the
addition of any fluids to the transmission, other than
those automatic transmission fluids listed above.
Exceptions to this policy are the use of special dyes
to aid in detecting fluid leaks.
Various ªspecialº additives and supplements exist
that claim to improve shift feel and/or quality. These
additives and others also claim to improve converter
clutch operation and inhibit overheating, oxidation,
varnish, and sludge. These claims have not been sup-
ported to the satisfaction of DaimlerChrysler and
these additivesmust not be used.The use of trans-
mission ªsealersº should also be avoided, since they
may adversely affect the integrity of transmission
seals.
OPERATION - AUTOMATIC TRANSMISSION
FLUID
The automatic transmission fluid is selected based
upon several qualities. The fluid must provide a high
level of protection for the internal components by
providing a lubricating film between adjacent metal
components. The fluid must also be thermally stable
so that it can maintain a consistent viscosity through
a large temperature range. If the viscosity stays con-
stant through the temperature range of operation,transmission operation and shift feel will remain con-
sistent. Transmission fluid must also be a good con-
ductor of heat. The fluid must absorb heat from the
internal transmission components and transfer that
heat to the transmission case.
FLUID CAPACITIES
SPECIFICATIONS - FLUID CAPACITIES
DESCRIPTION SPECIFICATION
ENGINE COOLANT
10 Liters 10.5 Quarts
ENGINE OIL
9.0L with Filter
Replacement9.5 Quarts with Filter
Replacement
AUTOMATIC TRANSMISSION
Service Fill - NAG1 5.0 L (10.6 pts.)
O-haul Fill - NAG1 7.7 L (16.3 pts.)
Dry fill capacity Depending on type and size of
internal cooler, length and inside diameter of cooler
lines, or use of an auxiliary cooler, these figures may
vary. (Refer to appropriate 21 - TRANSMISSION/
AUTOMATIC/FLUID - STANDARD PROCEDURE).
REAR AXLE   .03L (1 oz.)
8 1/2 1.8 L (4.0 pts.)
FUEL TANK
Primary 100 L (26.4 gal.)*
Reserve 10.5 L (2.8 gal.)*
*Nominal refill capacities are shown. A variation may
be observed from vehicle to vehicle due to
manufacturing tolerance and refill procedure
POWER STEERING SYSTEM
Power steering fluid capacities are dependent on
engine/chassis options as well as steering gear/cooler
options. Depending on type and size of internal
cooler, length and inside diameter of cooler lines, or
use of an auxiliary cooler, these capacities may vary.
Refer to 19, Steering for proper fill and bleed
procedures.
FLUID FILL/CHECK
LOCATIONS
INSPECTION - FLUID FILL/CHECK LOCATIONS
The fluid fill/check locations and lubrication points
are located in each applicable group.
0 - 4 LUBRICATION & MAINTENANCEVA
FLUID TYPES (Continued)

If the Engine is Damaged
For towing distances up to 30 miles (about 50
km)
²Shift selector lever in ªNº position.
²Do not exceed a towing speed of 30 m.p.h. (50
km/h).
For towing distances greater than 30 mile
(about 50 km)
²Remove the propeller shafts leading to the drive
axles. The vehicle can be towed without restriction.
If the Transmission is Damaged
²Remove the propeller shafts leading to the drive
axles. The vehicle can be towed without restriction.
If the Front Axle is Damaged
²Raise the front axle.
²Observe the same towing restrictions as for
engine damage.
If the Rear Axle is Damaged
²Raise the rear axle.
NOTE: Comply with local legal regulations regard-
ing towing vehicles.
SAFETY PRECAUTIONS
NOTE: The following safety precautions must be
observed when towing a vehicle.
²Secure loose and protruding parts.
²Always use a safety chain system that is inde-
pendent of the lifting and towing equipment.
²Do not allow towing equipment to contact the
disabled vehicle's fuel tank.
²Do not allow anyone under the disabled vehicle
while it is lifted by the towing device.
²Do not allow passengers to ride in a vehicle
being towed.
²Always observe state and local laws regarding
towing regulations.
²Do not tow a vehicle in a manner that could
jeopardize the safety of the operator, pedestrians or
other motorists.
²Do not attach tow chains, T-hooks, J-hooks, or a
tow sling to a bumper, steering linkage, drive shafts
or a non-reinforced frame hole.
²Remove exhaust pipe tips that interfere with the
tow sling and crossbar
²Padding should be placed between the tow sling/
crossbar and any painted surfaces
²When placing tow hooks on the rear axle, posi-
tion them so they do not damage the brake tubing or
hoses²Do not tow the vehicle by connecting to the front
or rear shock absorbers
²Do not tow a heavily loaded vehicle. Damage to
the vehicle may result. Use a flatbed device to trans-
port a loaded vehicle.
GROUND CLEARANCE
CAUTION: If vehicle is towed with wheels removed,
install lug nuts to retain brake drums.
A towed vehicle should be raised until lifted wheels
are a minimum 100 mm (4 in) from the ground. Be
sure there is adequate ground clearance at the oppo-
site end of the vehicle, especially when towing over
rough terrain, steep rises in the road or if the vehicle
is equipped with air dams, spoilers, and/or ground
effect panels. If necessary, remove the wheels from
the lifted end of the vehicle and lower the vehicle
closer to the ground, to increase the ground clearance
at the opposite end of the vehicle. Install lug nuts on
wheel attaching studs to retain brake drums.
RAMP ANGLE
If a vehicle with flat-bed towing equipment is used,
the approach ramp angle should not exceed 15
degrees.
TOWING WHEN KEYS ARE NOT AVAILABLE
When the vehicle is locked and keys are not avail-
able, use a flat bed hauler. A Wheel-lift or Sling-type
device can be used provided all the wheels are lifted
off the ground using tow dollies.
MAINTENANCE SCHEDULES
DESCRIPTION
The use of Special lubricant additives is not recom-
mended. The use of such additives may affect the
warranty rights. With regard to legal stipulations
concerning emissions control, please note that
engines have to be serviced and adjusted in accor-
dance with special instructions and using special
measuring equipment. Modifications to or interfer-
ence with the emissions control systems are not per-
missible.
MAINTENANCE - WITHOUT ASSYST
MAINTENANCE COMPUTER
Maintenance Intervals
²Oil service ±Normal Operationevery 10,000
miles or 16,000 km or 12 months.
²Maintenance service every 20,000 miles or
32,000 km.
Additional work must be carried out at yearly
intervals.
VALUBRICATION & MAINTENANCE 0 - 7
TOWING (Continued)

MAINTENANCE - WITH ASSYST MAINTENANCE
COMPUTER
ASSYST provides information on the best possible
timing for maintenance work.
NOTE: The engine manufacturer strongly recom-
mends the use of synthetic engine oils, such as
TMobil 1 SAE 0W-40.
When the next maintenance service is due, this
will be indicated in the multi-function display with
the wrench icon symbol displayed in km/miles or
days.
²One wrench icon showing indicates Oil Service
is necessary.
²Two wrench icons showing indicates Mainte-
nance Service is necessary ± displayed in km/miles or
days.
If the display shows the number of days, a clock
symbol will also appear in the multi-function display.
You should have the maintenance performed
within the stated period/distance.
The service indicator should be reset after an oil
service and/or maintenance service has been per-
formed.
REGULAR CHECK-UPS
To maintain the safe operation of the vehicle, it is
recommended that the following tasks be performed
on a regular basis (i.e. weekly or whenever the vehi-
cle is refueled). Check:
²Engine oil level
²Brake system, clutch mechanism ± fluid level
²Battery ± acid level
²Windshield washer system and headlamp clean-
ing system ± fluid level
²Mechanical assemblies (e. g. engine, transmis-
sion, etc.) ± check for leaks
²Condition of tires and tires pressures
²All exterior lights
SPECIAL MAINTENANCE REQUIREMENTS
If bodies built by manufacturers other than
DaimlerChrysler Corporation are fitted to the vehi-
cle, the maintenance requirements and lubrication
intervals specified by the body manufacturer must be
adhered to, in addition to all standard maintenance
requirements.
Brake Fluid
Only use brake fluids approved by the manufac-
turer (DOT 4 plus).
Coolant
Corrosion inhibitor/antifreeze concentration in the
coolant should be checked before the onset of winter
(once year in countries with high prevailing temper-
atures).Replace the coolant every five years or 100,000
miles.
Dust Filter for Heating/Ventilation Replace-
ment
The dust filter and the tailgate interior filter are to
be renewed during routine maintenance service. If
operating conditions are dusty, these filters should be
renewed more frequently.
ENGINE OIL CHANGE AND FILTER REPLACEMENT
At the minimum, change the engine oil and oil fil-
ter once a year ± even if the vehicle mileage per year
is extremely low. For standard oil service schedules
refer to the chapter oil service and maintenance ser-
vice.
Once a Year
Select the viscosity of the engine oil (SAE classes)
according to the outside air temperature.
Only use engine oil approved by DaimlerChrysler
Corporation if following the ASSYST system guide-
lines.
If the fuel used has a sulphur content exceeding
0.05% by weight, the service intervals should be split
in half.
SCOPE OF WORK FOR MAINTENANCE SERVICE
Oil Service
²Engine:
Oil change and filter replacement
Check fluid levels of the following system,
refill as necessary.
²If fluid is lost, trace and eliminate cause ± as a
separate order.
²Power-assisted steering
Lubrication work:
²Trailer tow hitch (original equipment)
Maintenance
²ASSYST maintenance computer reset
Function check
²Signalling system, warning and indicator lamps
²Headlamps, exterior lighting
²Windshield wipers, windshield washer system
Check for leaks and damage.
²Check for abrasion points and ensure that lines
are correctly routed!
²All lines and hoses, sensor cables
²Rubber boots on front axle drive shafts, rubber
boots on front axle suspension ball joints, shock
absorbers
Check fluid levels for the following systems,
correct as necessary.
NOTE: Should there be a loss of fluid which cannot
be explained by regular use, trace and eliminate the
cause.
0 - 8 LUBRICATION & MAINTENANCEVA
MAINTENANCE SCHEDULES (Continued)

²Engine cooling system. Check corrosion inhibi-
tor/antifreeze, refill as necessary.
²Hydraulic brake system
²Battery
²Windshield washer system
Engine
²Fuel filter renewal
²Air cleaner with maintenance indicator:
²Check degree of contamination.
²Air cleaner filter element renewed as necessary.
Chassis and body
²Trailer coupling:
Check operation, play and retaining fixtures
²Secondary rubber springs:
Visual check
²Tire pressures:
Correct as necessary, including spare tire
²Check thickness of brake pads
²Brake test
²Check condition of steering mechanism
²Heating/ventilation dust filter renewal
ADDITIONAL MAINTENANCE WORK
Automatic transmission once only at 80,000
miles/128000 km
Oil and filter change
During every second maintenance service
Air cleaner without maintenance indicator:
Air cleaner filter element renewal
Check poly-V-belt for wear and signs of damage
During every 6th maintenance service
Rear axle
ADDITIONAL MAINTENANCE WORK AFTER YEARS
Every 3 years
Air cleaner filter element renewal (note installa-
tion date)
Every 5 years or 100,000 miles
Coolant renewal
Note coolant composition
INTERNATIONAL SYMBOLS
DESCRIPTION
DaimlerChrysler Corporation uses international
symbols to identify engine compartment lubricant
and fluid inspection and fill locations (Fig. 3).
Fig. 3 INTERNATIONAL SYMBOLS
VALUBRICATION & MAINTENANCE 0 - 9
MAINTENANCE SCHEDULES (Continued)

²Battery Holddown- The battery holddown
hardware secures the battery in the battery tray in
the engine compartment.
²Battery Tray- The battery tray provides a
secure mounting location in the vehicle for the bat-
tery and an anchor point for the battery holddown
hardware.
For battery system maintenance schedules and
jump starting procedures, see the owner's manual in
the vehicle glove box. Optionally, refer to the Lubri-
cation and Maintenance section of this manual for
the recommended battery maintenance schedules and
for the proper battery jump starting procedure. While
battery charging can be considered a maintenance
procedure, the battery charging procedure and
related information are located later in this section of
this service manual. This was done because the bat-
tery must be fully-charged before any battery system
diagnosis or testing procedures can be performed.
OPERATION
The battery system is designed to provide a safe,
efficient, reliable and mobile means of delivering and
storing electrical energy. This electrical energy is
required to operate the engine starting system, as
well as to operate many of the other vehicle acces-
sory systems for limited durations while the engine
and/or the charging system are not operating. The
battery system is also designed to provide a reserve
of electrical energy to supplement the charging sys-
tem for short durations while the engine is running
and the electrical current demands of the vehicle
exceed the output of the charging system. In addition
to delivering, and storing electrical energy for the
vehicle, the battery system serves as a capacitor and
voltage stabilizer for the vehicle electrical system. It
absorbs most abnormal or transient voltages caused
by the switching of any of the electrical components
or circuits in the vehicle.
DIAGNOSIS AND TESTING - BATTERY SYSTEM
The battery, starting, and charging systems in the
vehicle operate with one another and must be testedas a complete system. In order for the engine to start
and the battery to maintain its charge properly, all of
the components that are used in these systems must
perform within specifications. It is important that
the battery, starting, and charging systems be thor-
oughly tested and inspected any time a battery needs
to be charged or replaced. The cause of abnormal bat-
tery discharge, overcharging or early battery failure
must be diagnosed and corrected before a battery is
replaced and before a vehicle is returned to service.
The service information for these systems has been
separated within this service manual to make it eas-
ier to locate the specific information you are seeking.
However, when attempting to diagnose any of these
systems, it is important that you keep their interde-
pendency in mind.
The diagnostic procedures used for the battery,
starting, and charging systems include the most
basic conventional diagnostic methods, to the more
sophisticated On-Board Diagnostics (OBD) built into
the Powertrain Control Module (PCM). Use of an
induction-type milliampere ammeter, a volt/ohmme-
ter, a battery charger, a carbon pile rheostat (load
tester) and a 12-volt test lamp may be required. All
OBD-sensed systems are monitored by the PCM.
Each monitored circuit is assigned a Diagnostic Trou-
ble Code (DTC). The PCM will store a DTC in elec-
tronic memory for any failure it detects. Refer to
Charging System for the proper charging system on-
board diagnostic test procedures.
MICRO 420 BATTERY TESTER
The Micro 420 automotive battery tester is
designed to help the dealership technicians diagnose
the cause of a defective battery. Follow the instruc-
tion manual supplied with the tester to properly
diagnose a vehicle. If the instruction manual is not
available refer to the standard procedure in this sec-
tion, which includes the directions for using the
Micro 420 battery tester.
8F - 2 BATTERY SYSTEMVA
BATTERY SYSTEM (Continued)

ABNORMAL BATTERY DISCHARGING
Any of the following conditions can result in abnor-
mal battery discharging:
1. A faulty or incorrect charging system compo-
nent. Refer to Charging System for additional charg-
ing system diagnosis and testing procedures.
2. A faulty or incorrect battery. Use Micro 420 bat-
tery tester and refer to Battery System for additional
battery diagnosis and testing procedures.
3. A faulty circuit or component causing excessive
ignition-off draw.
4. Electrical loads that exceed the output of the
charging system. This can be due to equipment
installed after manufacture, or repeated short trip
use.
5. A faulty or incorrect starting system component.
Refer to Starting System for the proper starting sys-
tem diagnosis and testing procedures.
6. Corroded or loose battery posts and/or terminal
clamps.
7. Slow driving speeds (heavy traffic conditions) or
prolonged idling, with high-amperage draw systems
in use.
CLEANING
The following information details the recommended
cleaning procedures for the battery and related com-
ponents. In addition to the maintenance schedules
found in this service manual and the owner's man-
ual, it is recommended that these procedures be per-
formed any time the battery or related components
must be removed for vehicle service.
(1) Clean the battery cable terminal clamps of all
corrosion. Remove any corrosion using a wire brush
or a post and terminal cleaning tool, and a sodium
bicarbonate (baking soda) and warm water cleaning
solution (Fig. 1).
(2) Clean the battery tray and battery hold down
hardware of all corrosion. Remove any corrosion
using a wire brush and a sodium bicarbonate (baking
soda) and warm water cleaning solution. Paint any
exposed bare metal.
(3) If the removed battery is to be reinstalled,
clean the outside of the battery case and the top
cover with a sodium bicarbonate (baking soda) and
warm water cleaning solution using a stiff bristle
parts cleaning brush to remove any acid film (Fig. 2).
Rinse the battery with clean water. Ensure that the
cleaning solution does not enter the battery cells
through the vent holes. If the battery is being
replaced, refer to Battery System Specifications for
the factory-installed battery specifications. Confirm
that the replacement battery is the correct size and
has the correct ratings for the vehicle.
(4) If the vehicle is so equipped, clean the battery
thermal guard with a sodium bicarbonate (bakingsoda) and warm water cleaning solution using a stiff
bristle parts cleaning brush to remove any acid film.
Fig. 1 Clean Battery Cable Terminal Clamp - Typical
1 - TERMINAL BRUSH
2 - BATTERY CABLE
Fig. 2 Battery Cleaning - Typical
1 - CLEANING BRUSH
2 - WARM WATER AND BAKING SODA SOLUTION
3 - BATTERY
VABATTERY SYSTEM 8F - 5
BATTERY SYSTEM (Continued)

RELAY - INSTALLATION, STARTER
MOTOR............................8F-32
RELAY - INSTALLATION, TIME DELAY....8L-33
RELAY - INSTALLATION, TURN SIGNAL . . . 8L-24
RELAY - INSTALLATION, WIPER.........8R-22
RELAY - OPERATION................8W-97-5
RELAY - OPERATION, BLOWER MOTOR . . . 24-23
RELAY - OPERATION, GLOW PLUG........8I-2
RELAY - OPERATION, HEATED SEAT......8G-4
RELAY - OPERATION, WIPER...........8R-21
RELAY - REMOVAL.................8W-97-5
RELAY - REMOVAL, BLOWER MOTOR....24-24
RELAY - REMOVAL, DAYTIME RUNNING
LAMP...............................8L-9
RELAY - REMOVAL, FOG LAMP.........8L-10
RELAY - REMOVAL, HEATED SEAT........8G-4
RELAY - REMOVAL, STARTER MOTOR....8F-31
RELAY - REMOVAL, TIME DELAY........8L-32
RELAY - REMOVAL, TURN SIGNAL.......8L-24
RELAY - REMOVAL, WIPER............8R-22
RELAYS - DIAGNOSIS AND TESTING,
GLOW PLUG..........................8I-2
RELEASE CABLE - INSTALLATION, LATCH . 23-51
RELEASE CABLE - REMOVAL, LATCH.....23-51
RELEASE HANDLE - INSTALLATION,
LATCH .............................23-52
RELEASE HANDLE - REMOVAL, LATCH . . . 23-52
REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY KEY.............8Q-2
REMOTE ENTRY MODULE -
INSTALLATION, SENTRY KEY............8Q-4
REMOTE ENTRY MODULE - OPERATION,
SENTRY KEY.........................8Q-3
REMOTE ENTRY MODULE - REMOVAL,
SENTRY KEY.........................8Q-3
REMOTE KEYLESS ENTRY
TRANSMITTER - DESCRIPTION..........8N-2
REPAIR - DESCRIPTION, THREADED
HOLE.............................Intro.-5
REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD..................21-27
REPAIR - STANDARD PROCEDURE,
PLASTIC BODY PANEL.................23-3
REPAIRING CONNECTING RODS -
STANDARD PROCEDURE, CHECKING......9-40
REPAIRING LEAKS - STANDARD
PROCEDURE........................22-10
REPEATER LAMP BULB - INSTALLATION . . 8L-22
REPEATER LAMP BULB - REMOVAL......8L-22
REPEATER LAMP UNIT - INSTALLATION . . 8L-23
REPEATER LAMP UNIT - REMOVAL......8L-22
REPLACING ENGINE CORE AND OIL
GALLERY PLUGS - STANDARD
PROCEDURE.........................9-34
REQUIREMENTS - DESCRIPTION,
COOLING SYSTEM....................24-1
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-1
RESERVOIR - DESCRIPTION, WASHER . . . 8R-11
RESERVOIR - INSTALLATION, FLUID......5-15
RESERVOIR - INSTALLATION, WASHER . . . 8R-12
RESERVOIR - OPERATION, WASHER.....8R-11
RESERVOIR - REMOVAL, FLUID..........5-15
RESERVOIR - REMOVAL, WASHER
......8R-11
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR
....................24-16
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR
............24-16
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR
....................24-17
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR
....................24-16
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR
............................24-16
RESTRAINT DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL
......................8O-6
RESTRAINT SYSTEM - DIAGNOSIS AND
TESTING, SUPPLEMENTAL
..............8O-5
RESTRAINT SYSTEM - WARNINGS
.......8O-5
RESTRAINTS - DESCRIPTION
............8O-2
RESTRAINTS - OPERATION
.............8O-4
RESTRAINTS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED
SUPPLEMENTAL
......................8O-6
RESTRICTIONS - DIAGNOSIS AND
TESTING, FUEL SUPPLY
................14-5RETRACTOR - INSTALLATION, FRONT
SEAT BELT .........................8O-21
RETRACTOR - INSTALLATION, REAR
SEAT BELT .........................8O-29
RETRACTOR - REMOVAL, FRONT SEAT
BELT ..............................8O-19
RETRACTOR - REMOVAL, REAR SEAT
BELT ..............................8O-27
RETURN HOSE FROM GEAR TO COOLER
TUBE - INSTALLATION................19-15
RETURN HOSE FROM GEAR TO COOLER
TUBE - REMOVAL....................19-15
RETURN LINE FROM PUMP TO COOLER
TUBE - INSTALLATION................19-15
RETURN LINE FROM PUMP TO COOLER
TUBE - REMOVAL....................19-15
RIGHT MOUNT - INSTALLATION..........9-49
RIGHT MOUNT - REMOVAL.............9-49
RING FITTING - STANDARD
PROCEDURE, PISTON..................9-46
ROAD TESTING - DIAGNOSIS AND
TESTING...........................21-23
ROD - DESCRIPTION, PISTON &
CONNECTING.........................9-40
ROD - INSTALLATION, PROP...........23-52
ROD - REMOVAL, PROP...............23-52
ROD END - DIAGNOSIS AND TESTING,
OUTER TIE..........................19-10
ROD END - INSTALLATION, TIE.........19-11
ROD END - REMOVAL, TIE.............19-11
RODS - STANDARD PROCEDURE,
CHECKING AND REPAIRING
CONNECTING.........................9-40
ROLLER ARM - INSTALLATION, CENTER . . 23-38
ROLLER ARM - INSTALLATION, LOWER . . . 23-38
ROLLER ARM - INSTALLATION, UPPER . . . 23-37
ROLLER ARM - REMOVAL, CENTER......23-37
ROLLER ARM - REMOVAL, LOWER......23-38
ROLLER ARM - REMOVAL, UPPER.......23-37
ROTATION - STANDARD PROCEDURE,
TIRE................................22-5
RUNNING LAMP RELAY - INSTALLATION,
DAYTIME............................8L-9
RUNNING LAMP RELAY - REMOVAL,
DAYTIME............................8L-9
RUNOUT - DIAGNOSIS AND TESTING,
TIRE AND WHEEL.....................22-1
SAFETY LATCH - INSTALLATION.........23-52
SAFETY LATCH - REMOVAL............23-52
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD........................23-82
SANDING/BUFFING & POLISH -
DESCRIPTION, FINESSE...............23-75
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-7
SCHEMATICS AND DIAGRAMS,
DIAGNOSIS AND TESTING.............21-47
SCUFF PADS - INSTALLATION,
STEPWELL..........................23-73
SCUFF PADS - REMOVAL, STEPWELL....23-72
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL.....................9-38
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL.....................9-38
SEAL - INSTALLATION, OUTPUT SHAFT . . 21-125
SEAL - INSTALLATION, PINION...........3-22
SEAL - INSTALLATION, TORQUE
CONVERTER HUB...................21-147
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL.....................9-37
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL ................................9-37
SEAL - REMOVAL, OUTPUT SHAFT......21-125
SEAL - REMOVAL, PINION..............3-22
SEAL - REMOVAL, TORQUE CONVERTER
HUB..............................21-147
SEALS - INSTALLATION, DOOR OPENING . . 23-87
SEALS - REMOVAL, DOOR OPENING.....23-87
SEAT - FRONT - INSTALLATION.........23-77
SEAT - FRONT - REMOVAL.............23-77
SEAT - REAR - INSTALLATION
..........23-79
SEAT - REAR - REMOVAL
..............23-79
SEAT ADJUSTERS - FRONT -
INSTALLATION
.......................23-78
SEAT ADJUSTERS - FRONT - REMOVAL
. . . 23-78
SEAT BACK - FRONT - INSTALLATION
....23-77SEAT BACK - FRONT - REMOVAL........23-77
SEAT BACK CUSHION/COVER - REAR -
INSTALLATION.......................23-80
SEAT BACK CUSHION/COVER - REAR -
REMOVAL..........................23-80
SEAT BACK SHIELD - INSTALLATION,
REAR..............................23-79
SEAT BACK SHIELD - REMOVAL, REAR . . . 23-79
SEAT BELT & RETRACTOR -
INSTALLATION, FRONT................8O-21
SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-29
SEAT BELT & RETRACTOR - REMOVAL,
FRONT.............................8O-19
SEAT BELT & RETRACTOR - REMOVAL,
REAR..............................8O-27
SEAT BELT BUCKLE - INSTALLATION,
FRONT.............................8O-23
SEAT BELT BUCKLE - REMOVAL, FRONT . . 8O-22
SEAT BELT SWITCH - DESCRIPTION.....8O-31
SEAT BELT SWITCH - OPERATION.......8O-31
SEAT BELT TENSIONER - DESCRIPTION . . . 8O-31
SEAT BELT TENSIONER - OPERATION....8O-32
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-34
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-33
SEAT CUSHION - FRONT -
INSTALLATION.......................23-78
SEAT CUSHION - FRONT - REMOVAL.....23-78
SEAT CUSHION/COVER - REAR -
INSTALLATION.......................23-80
SEAT CUSHION/COVER - REAR -
REMOVAL..........................23-80
SEAT ELEMENT - DESCRIPTION, HEATED . . 8G-3
SEAT ELEMENT - DIAGNOSIS AND
TESTING, HEATED.....................8G-3
SEAT ELEMENT - OPERATION, HEATED....8G-3
SEAT RELAY - DESCRIPTION, HEATED.....8G-4
SEAT RELAY - DIAGNOSIS AND
TESTING, HEATED.....................8G-4
SEAT RELAY - INSTALLATION, HEATED....8G-4
SEAT RELAY - OPERATION, HEATED......8G-4
SEAT RELAY - REMOVAL, HEATED........8G-4
SEAT SENSOR - DESCRIPTION, HEATED . . . 8G-4
SEAT SENSOR - DIAGNOSIS AND
TESTING, HEATED.....................8G-4
SEAT SWITCH - DESCRIPTION, DRIVER
HEATED.............................8G-2
SEAT SWITCH - DESCRIPTION,
PASSENGER HEATED..................8G-5
SEAT SWITCH - DIAGNOSIS AND
TESTING, DRIVER HEATED..............8G-2
SEAT SWITCH - DIAGNOSIS AND
TESTING, PASSENGER HEATED..........8G-5
SEAT SWITCH - INSTALLATION, DRIVER
HEATED.............................8G-3
SEAT SWITCH - INSTALLATION,
PASSENGER HEATED..................8G-5
SEAT SWITCH - OPERATION, DRIVER
HEATED.............................8G-2
SEAT SWITCH - OPERATION,
PASSENGER HEATED..................8G-5
SEAT SWITCH - REMOVAL, DRIVER
HEATED.............................8G-3
SEAT SWITCH - REMOVAL, PASSENGER
HEATED.............................8G-5
SEATBELT INDICATOR - DESCRIPTION....8J-22
SEATBELT INDICATOR - OPERATION......8J-22
SEATS - DESCRIPTION, HEATED.........8G-1
SEATS - DIAGNOSIS AND TESTING,
HEATED.............................8G-2
SEATS - OPERATION, HEATED...........8G-2
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-5
SECURITY - DESCRIPTION, VEHICLE
THEFT..............................8Q-1
SECURITY - DIAGNOSIS AND TESTING,
VEHICLE THEFT.......................8Q-1
SECURITY - OPERATION, VEHICLE THEFT
. . 8Q-1
SECURITY SYSTEM MODULE -
INSTALLATION
.......................8Q-2
SECURITY SYSTEM MODULE -
REMOVAL
...........................8Q-2
SELECTOR INDICATOR - DESCRIPTION,
GEAR
..............................8J-17
SELECTOR INDICATOR - OPERATION,
GEAR
..............................8J-17
14 INDEXVA
Description Group-Page Description Group-Page Description Group-Page