2005 MERCEDES-BENZ SPRINTER audio

(12) Install the cover to the instrument cluster.
(13) Install glove compartment.
(14) Install the radio (Refer to 8 - ELECTRICAL/
AUDIO/RADIO - INSTALLATION).
(15) Reconnect the battery negative cable.
IN-CAR TEMPERATURE
SENSOR
DESCRIPTION
The in-car temperature sensor measures the actual
air temperature within the passenger compartment.
The in-car temperature sensor is located inside of the
A/C-heater control behind a vented panel (Fig. 14)
and is not a separate serviceable component. The
A/C-heater control must be replaced if there is a fault
relating to the in-car temperature sensor.
OPERATION
Air from the passenger compartment flows over the
thermistor of the in-car temperature sensor. The
thermistor changes resistance with air temperature.
The ATC control module measures this resistance
and calculates the temperature of the air. The ATC
control module then makes adjustments to maintain
the selected passenger compartment temperature.
DIAGNOSIS AND TESTING
The in-car temperature sensor is diagnosed by per-
forming the ATC Function Test using the DRBIIIt
scan tool. Refer to Body Diagnostic Procedures. For
circuit descriptions and diagrams, refer to the appro-
priate wiring information.
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
If the in-car temperature sensor is verified to be
bad, the A/C-heater control must be replaced (Refer
to 24 - HEATING & AIR CONDITIONING/CON-
TROLS/A/C HEATER CONTROL - REMOVAL).
MODE DOOR CABLES
REMOVAL
The air distribution control cables (mode door
cables) can be removed and installed without having
to remove the instrument panel from the vehicle.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the center section of the instrument
panel (Refer to 23 - BODY/INSTRUMENT PANEL/
INSTRUMENT PANEL CENTER BEZEL - REMOV-
AL).
(3) Remove the heater-A/C control (Refer to 24 -
HEATING & AIR CONDITIONING/CONTROLS/A/C
HEATER CONTROL - REMOVAL).
(4) Mark and disconnect the control cables from
the A/C-heater control.
(5) Mark and disconnect the control cables from
the heater housing retainers (Fig. 15).
(6) Disconnect the control cables from the mode
door levers and remove the cables from the vehicle.
INSTALLATION
(1) Connect the two control cables to the mode
door levers (Fig. 16).
(2) Connect the two control cables to the A/C-
heater control.
NOTE: Install the control cable of bottom adjust-
ment lever to the front adjustment wheel of the A/C-
heater control.
(3) Hold the A/C-heater control in its installation
position.
Fig. 14 In-Car Temperature Sensor
1 - A/C-HEATER CONTROL
2 - IN-CAR TEMPERATURE SENSOR
VACONTROLS - FRONT 24 - 19
EVAPORATOR TEMPERATURE SENSOR (Continued)

INDEX
ABS INDICATOR - DESCRIPTION..........8J-9
ABS INDICATOR - OPERATION...........8J-9
A/C COMPRESSOR - DESCRIPTION......24-49
A/C COMPRESSOR - INSTALLATION......24-51
A/C COMPRESSOR - OPERATION........24-49
A/C COMPRESSOR - REMOVAL.........24-50
A/C COMPRESSOR CLUTCH -
DESCRIPTION........................24-8
A/C COMPRESSOR CLUTCH -
OPERATION..........................24-8
A/C CONDENSER - DESCRIPTION........24-52
A/C CONDENSER - INSTALLATION.......24-52
A/C CONDENSER - OPERATION..........24-52
A/C CONDENSER - REMOVAL...........24-52
A/C DISCHARGE LINE - INSTALLATION . . . 24-54
A/C DISCHARGE LINE - REMOVAL.......24-53
A/C EVAPORATOR - DESCRIPTION.......24-54
A/C EVAPORATOR - INSTALLATION......24-55
A/C EVAPORATOR - OPERATION.........24-54
A/C EVAPORATOR - REMOVAL..........24-55
A/C EXPANSION VALVE - DESCRIPTION . . . 24-55
A/C EXPANSION VALVE - DIAGNOSIS
AND TESTING.......................24-56
A/C EXPANSION VALVE - INSTALLATION . . 24-56
A/C EXPANSION VALVE - OPERATION.....24-55
A/C EXPANSION VALVE - REMOVAL.......24-56
A/C HEATER CONTROL - DESCRIPTION . . . 24-12
A/C HEATER CONTROL - INSTALLATION . . . 24-13
A/C HEATER CONTROL - OPERATION.....24-12
A/C HEATER CONTROL - REMOVAL......24-12
A/C HOUSING - INSTALLATION, REAR....24-41
A/C HOUSING - REMOVAL, REAR........24-40
A/C PERFORMANCE TEST - DIAGNOSIS
AND TESTING........................24-3
A/C PRESSURE TRANSDUCER -
DESCRIPTION.......................24-13
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING.............24-13
A/C PRESSURE TRANSDUCER -
INSTALLATION.......................24-14
A/C PRESSURE TRANSDUCER -
OPERATION.........................24-13
A/C PRESSURE TRANSDUCER -
REMOVAL..........................24-14
A/C SYSTEM, SPECIFICATIONS...........24-5
ACCELERATOR PEDAL POSITION
SENSOR - DESCRIPTION...............14-17
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING.........................7-5
ACCESSORY SWITCH BEZEL -
INSTALLATION.......................23-54
ACCESSORY SWITCH BEZEL - REMOVAL . . 23-54
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR................24-20
ACTUATOR - INSTALLATION, INSIDE
HANDLE.......................23-34,23-37
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-21
ACTUATOR - OPERATION,
RECIRCULATION DOOR................24-20
ACTUATOR - REMOVAL, INSIDE HANDLE . 23-34,
23-37
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-21
ADAPTATION - STANDARD PROCEDURE,
TCM................................8E-8
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE................7-11
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING..................7-11
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-34
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-33
ADJUSTERS - FRONT - INSTALLATION,
SEAT ..............................23-78
ADJUSTERS - FRONT - REMOVAL, SEAT . . 23-78
AFTER A SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE.................8O-6
AIR CLEANER ELEMENT - INSTALLATION . . 9-20
AIR CLEANER ELEMENT - REMOVAL
......9-20
AIR CLEANER HOUSING - INSTALLATION
. . 9-20
AIR CLEANER HOUSING - REMOVAL
......9-20
AIR CONDITIONER - DESCRIPTION,
HEATER
.............................24-1
AIR CONDITIONER - OPERATION,
HEATER
.............................24-2AIR COOLER AND PLUMBING -
CLEANING, CHARGE...................11-5
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE................11-4
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE.................11-5
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE................11-5
AIR COOLER AND PLUMBING -
OPERATION, CHARGE..................11-4
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE...................11-5
AIR COOLER SYSTEM - LEAKS -
DIAGNOSIS AND TESTING, CHARGE.......11-4
AIR FILTER - INSTALLATION.......24-31,24-39
AIR FILTER - REMOVAL..........24-31,24-39
AIR FLOW (MAF) SENSOR -
DESCRIPTION, MANIFOLD.............14-30
AIR FLOW (MAF) SENSOR -
INSTALLATION, MANIFOLD.............14-31
AIR FLOW (MAF) SENSOR - OPERATION,
MANIFOLD..........................14-30
AIR FLOW (MAF) SENSOR - REMOVAL,
MANIFOLD..........................14-31
AIR GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH................24-9
AIR IN FUEL SYSTEM - DIAGNOSIS AND
TESTING............................14-2
AIR OUTLET TEMPERATURE SENSOR -
DESCRIPTION.......................24-14
AIR OUTLET TEMPERATURE SENSOR -
INSTALLATION.......................24-15
AIR OUTLET TEMPERATURE SENSOR -
OPERATION.........................24-15
AIR OUTLET TEMPERATURE SENSOR -
REMOVAL..........................24-15
AIR OUTLETS - INSTALLATION..........24-32
AIR OUTLETS - REMOVAL.............24-31
AIR TEMPERATURE SENSOR -
DESCRIPTION, INLET.................14-29
AIR TEMPERATURE SENSOR -
INSTALLATION, INLET.................14-30
AIR TEMPERATURE SENSOR -
OPERATION, INLET...................14-29
AIR TEMPERATURE SENSOR -
REMOVAL, INLET....................14-30
AIRBAG - DESCRIPTION, DRIVER........8O-16
AIRBAG - DESCRIPTION, PASSENGER....8O-23
AIRBAG - INSTALLATION, DRIVER.......8O-18
AIRBAG - INSTALLATION, PASSENGER . . . 8O-26
AIRBAG - OPERATION, DRIVER.........8O-17
AIRBAG - OPERATION, PASSENGER......8O-24
AIRBAG - REMOVAL, DRIVER...........8O-17
AIRBAG - REMOVAL, PASSENGER.......8O-24
AIRBAG BRACKET - INSTALLATION,
PASSENGER........................8O-27
AIRBAG BRACKET - REMOVAL,
PASSENGER........................8O-27
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-8
AIRBAG CONTROL MODULE -
INSTALLATION......................8O-11
AIRBAG CONTROL MODULE -
OPERATION..........................8O-9
AIRBAG CONTROL MODULE - REMOVAL . . 8O-10
AIRBAG INDICATOR - DESCRIPTION......8J-10
AIRBAG INDICATOR - OPERATION.......8J-10
ALB CONTROLLER - INSTALLATION
.......5-15
ALB CONTROLLER - REMOVAL
...........5-15
ALB LEVER - INSTALLATION
.............5-15
ALB LEVER - REMOVAL
................5-15
ALIGNMENT - DESCRIPTION, WHEEL
......2-17
ALIGNMENT - SPECIFICATIONS, WHEEL
....2-19
ALUMINUM THREAD REPAIR -
STANDARD PROCEDURE
...............21-27
AMBIENT TEMPERATURE INDICATOR -
DESCRIPTION
.......................8J-11
AMBIENT TEMPERATURE INDICATOR -
OPERATION
.........................8J-11
AMBIENT TEMPERATURE SENSOR -
DESCRIPTION
.......................24-15
AMBIENT TEMPERATURE SENSOR -
INSTALLATION
.......................24-16
AMBIENT TEMPERATURE SENSOR -
OPERATION
.........................24-15
AMBIENT TEMPERATURE SENSOR -
REMOVAL
..........................24-15ANTENNA BODY & CABLE -
INSTALLATION.......................8A-1
ANTENNA BODY & CABLE - REMOVAL.....8A-1
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL..................8A-2
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL..................8A-1
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER........................8E-3
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER........................8E-3
ANTILOCK BRAKE - REMOVAL,
CONTROLLER........................8E-3
A-PILLAR TRIM - INSTALLATION........23-68
A-PILLAR TRIM - REMOVAL............23-67
ARM - DESCRIPTION, WIPER...........8R-13
ARM - INSTALLATION, CENTER ROLLER . . 23-38
ARM - INSTALLATION, LOWER CONTROL . . . 2-6
ARM - INSTALLATION, LOWER ROLLER . . . 23-38
ARM - INSTALLATION, UPPER ROLLER . . . 23-37
ARM - INSTALLATION, WIPER..........8R-14
ARM - OPERATION, WIPER............8R-14
ARM - REMOVAL, CENTER ROLLER......23-37
ARM - REMOVAL, LOWER CONTROL.......2-6
ARM - REMOVAL, LOWER ROLLER......23-38
ARM - REMOVAL, UPPER ROLLER.......23-37
ARM - REMOVAL, WIPER..............8R-14
ARMREST - INSTALLATION.............23-76
ARMREST - REMOVAL................23-76
ASH RECEIVER - INSTALLATION.........23-55
ASH RECEIVER - REMOVAL............23-55
ASH RECEIVER/CIGAR LIGHTER LAMP
UNIT - INSTALLATION.................8L-27
ASH RECEIVER/CIGAR LIGHTER LAMP
UNIT - REMOVAL....................8L-27
ASSIST HANDLE - INSTALLATION........23-68
ASSIST HANDLE - REMOVAL...........23-68
AUDIO, SPECIAL TOOLS................8A-1
AUTOMATIC TRANSMISSION -
DIAGNOSIS AND TESTING........21-23,21-24
AUTOMATIC TRANSMISSION - NAG1 -
DESCRIPTION........................21-2
AUTOMATIC TRANSMISSION - NAG1 -
OPERATION..........................21-4
AUTOMATIC TRANSMISSION - SPECIAL
TOOLS, NAG1.......................21-69
AUTOMATIC TRANSMISSION -
SPECIFICATIONS, NAG1...............21-68
AUTOMATIC TRANSMISSION FLUID -
NAG1 - DESCRIPTION...................0-4
AUTOMATIC TRANSMISSION FLUID -
OPERATION...........................0-4
AUXILIARY BATTERY INSTALLATION,
INSTALLATION.......................8F-13
AUXILIARY BATTERY REMOVAL,
REMOVAL..........................8F-13
AXLE - DESCRIPTION...................0-3
AXLE - DESCRIPTION, REAR.............3-10
AXLE - DIAGNOSIS AND TESTING, REAR . . . 3-10
AXLE - INSTALLATION, REAR............3-12
AXLE - OPERATION, REAR..............3-10
AXLE - REMOVAL, REAR................3-11
AXLE - SPECIAL TOOLS, REAR...........3-14
AXLE - SPECIFICATIONS, REAR..........3-13
AXLE BEARINGS/SEALS - INSTALLATION . . . 3-17
AXLE BEARINGS/SEALS - REMOVAL......3-17
AXLE HUB BEARINGS/SEALS -
INSTALLATION........................3-20
AXLE HUB BEARINGS/SEALS - REMOVAL . . 3-20
AXLE SHAFTS - DUAL REAR WHEELS -
INSTALLATION........................3-19
AXLE SHAFTS - DUAL REAR WHEELS -
REMOVAL...........................3-19
AXLE SHAFTS - INSTALLATION...........3-15
AXLE SHAFTS - REMOVAL..............3-15
B1 - ASSEMBLY, HOLDING CLUTCH.....21-113
B1 - DISASSEMBLY, HOLDING CLUTCH . . 21-112
B2 - ASSEMBLY, HOLDING CLUTCH.....21-116
B2 - DISASSEMBLY, HOLDING CLUTCH . . 21-115
BACK - FRONT - INSTALLATION, SEAT....23-77
BACK - FRONT - REMOVAL, SEAT
.......23-77
BACK CUSHION/COVER - REAR -
INSTALLATION, SEAT
.................23-80
BACK CUSHION/COVER - REAR -
REMOVAL, SEAT
.....................23-80
BACK SHIELD - INSTALLATION, REAR
SEAT
..............................23-79
BACK SHIELD - REMOVAL, REAR SEAT
. . . 23-79
VAINDEX 1
Description Group-Page Description Group-Page Description Group-Page

TEMPERATURE SENSOR -
INSTALLATION, FUEL.................14-29
TEMPERATURE SENSOR -
INSTALLATION, INLET AIR.............14-30
TEMPERATURE SENSOR -
INSTALLATION, OIL....................9-57
TEMPERATURE SENSOR - OPERATION....24-30
TEMPERATURE SENSOR - OPERATION,
AIR OUTLET........................24-15
TEMPERATURE SENSOR - OPERATION,
AMBIENT...........................24-15
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR..................24-18,24-26
TEMPERATURE SENSOR - OPERATION,
FUEL..............................14-29
TEMPERATURE SENSOR - OPERATION,
IN-CAR............................24-19
TEMPERATURE SENSOR - OPERATION,
INLET AIR..........................14-29
TEMPERATURE SENSOR - OPERATION,
OIL ................................9-56
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION.....................21-141
TEMPERATURE SENSOR - REMOVAL.....24-30
TEMPERATURE SENSOR - REMOVAL,
AIR OUTLET........................24-15
TEMPERATURE SENSOR - REMOVAL,
AMBIENT...........................24-15
TEMPERATURE SENSOR - REMOVAL,
EVAPORATOR..................24-18,24-26
TEMPERATURE SENSOR - REMOVAL,
FUEL..............................14-29
TEMPERATURE SENSOR - REMOVAL,
IN-CAR............................24-19
TEMPERATURE SENSOR - REMOVAL,
INLET AIR..........................14-30
TEMPERATURE SENSOR - REMOVAL,
OIL ................................9-57
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-31
TENSIONER - INSTALLATION, CABLE......5-23
TENSIONER - INSTALLATION, TIMING
CHAIN..............................9-71
TENSIONER - OPERATION, SEAT BELT....8O-32
TENSIONER - REMOVAL, CABLE..........5-23
TENSIONER - REMOVAL, TIMING CHAIN . . . 9-70
TENSIONERS - DESCRIPTION, BELT........7-5
TENSIONERS - OPERATION, BELT..........7-5
TENSIONING AND SLIDE RAIL -
INSTALLATION........................9-66
TENSIONING AND SLIDE RAILS -
REMOVAL...........................9-61
TENSIONING RAIL - INSTALLATION,
TIMING CHAIN.......................9-66
TENSIONING RAIL - REMOVAL, TIMING
CHAIN..............................9-63
TERMINAL - INSTALLATION.........8W-01-10
TERMINAL - REMOVAL..............8W-01-9
TEST - DIAGNOSIS AND TESTING, A/C
PERFORMANCE.......................24-3
TEST - DIAGNOSIS AND TESTING,
FUNCTION...........................24-3
TEST - STANDARD PROCEDURE,
CYLINDER LEAK DOWN.................9-3
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-10
TEST - STANDARD PROCEDURE, LOW
PRESSURE FUEL PUMP................14-3
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-10
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-7
TESTER - STANDARD PROCEDURE,
USING MICRO 420 BATTERY............8F-11
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - DIAGNOSIS AND
TESTING, VEHICLE....................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THERMOSTAT - INSTALLATION, ENGINE
COOLANT
............................7-16
THERMOSTAT - REMOVAL, ENGINE
COOLANT
............................7-15
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM
..............21-27
THREADED HOLE REPAIR -
DESCRIPTION
......................Intro.-5
TIE ROD END - DIAGNOSIS AND
TESTING, OUTER
.....................19-10TIE ROD END - INSTALLATION..........19-11
TIE ROD END - REMOVAL..............19-11
TIME DELAY RELAY - INSTALLATION.....8L-33
TIME DELAY RELAY - REMOVAL.........8L-32
TIMER MODULE - DESCRIPTION,
CENTRAL............................8E-1
TIMER MODULE - DIAGNOSIS AND
TESTING, CENTRAL....................8E-2
TIMER MODULE - INSTALLATION,
CENTRAL............................8E-2
TIMER MODULE - OPERATION, CENTRAL . . 8E-2
TIMER MODULE - REMOVAL, CENTRAL....8E-2
TIMING CHAIN - INSTALLATION..........9-67
TIMING CHAIN - REMOVAL..............9-63
TIMING CHAIN COVER - INSTALLATION....9-60
TIMING CHAIN COVER - REMOVAL.......9-59
TIMING CHAIN TENSIONER -
INSTALLATION........................9-71
TIMING CHAIN TENSIONER - REMOVAL....9-70
TIMING CHAIN TENSIONING RAIL -
INSTALLATION........................9-66
TIMING CHAIN TENSIONING RAIL -
REMOVAL...........................9-63
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-3
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE CARRIER - INSTALLATION, SPARE . . . 22-10
TIRE CARRIER - REMOVAL, SPARE......22-10
TIRE INFLATION PRESSURES -
DESCRIPTION........................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-8
TIRE PRESSURE FOR HIGH SPEEDS -
DESCRIPTION........................22-6
TIRE ROTATION - STANDARD
PROCEDURE.........................22-5
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-6
TIRES - DESCRIPTION, RADIAL - PLY.....22-6
TIRES - DESCRIPTION, REPLACEMENT....22-7
TIRES, SPECIFICATIONS...............22-10
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING............................22-8
TO COOLER TUBE - INSTALLATION,
RETURN HOSE FROM GEAR............19-15
TO COOLER TUBE - INSTALLATION,
RETURN LINE FROM PUMP............19-15
TO COOLER TUBE - REMOVAL, RETURN
HOSE FROM GEAR...................19-15
TO COOLER TUBE - REMOVAL, RETURN
LINE FROM PUMP....................19-15
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-8
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . . 8W-01-8
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOE ADJUSTMENT - STANDARD
PROCEDURE.........................2-19
TONE WHEEL - INSTALLATION...........5-31
TONE WHEEL - REMOVAL...............5-31
TOOLS - AUDIO, SPECIAL...............8A-1
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL......................8F-6
TOOLS - BRAKES, SPECIAL..............5-7
TOOLS - FRONT SUSPENSION, SPECIAL . . 19-11
TOOLS - FRONT SUSPENSION, SPECIAL....2-2
TOOLS - FUEL SYSTEM, SPECIAL........14-5
TOOLS - PARK BRAKE, SPECIAL.........5-23
TOOLS, IGNITION CONTROL - SPECIAL....8I-1
TOOLS, INSTALLATION - SPECIAL........9-14
TOOLS, NAG1 AUTOMATIC
TRANSMISSION - SPECIAL.............21-69
TOOLS, PROPELLER SHAFT - SPECIAL.....3-5
TOOLS, REAR AXLE - SPECIAL...........3-14
TOOLS, SPECIAL TOOLS - BATTERY
SYSTEM SPECIAL.....................8F-6
TOOLS, SPECIFICATIONS - SPECIAL......8F-17
TOP COVER - CLUSTER - INSTALLATION . . 23-62
TOP COVER - CLUSTER - REMOVAL.....23-62
TOP COVER - INSTALLATION
...........23-65
TOP COVER - REMOVAL
...............23-64
TOP COVER - TRAY - INSTALLATION
.....23-64
TOP COVER - TRAY - REMOVAL
.........23-63
TOUCH-UP - DESCRIPTION, PAINT
.......23-74TOUCH-UP - STANDARD PROCEDURE,
PAINT.............................23-75
TOWING - STANDARD PROCEDURE........0-6
TRACK - INSTALLATION, CENTER........23-39
TRACK - REMOVAL, CENTER...........23-38
TRACTION CONTROL INDICATOR -
DESCRIPTION.......................8J-24
TRACTION CONTROL INDICATOR -
OPERATION.........................8J-24
TRACTION CONTROL MALFUNCTION
INDICATOR - DESCRIPTION............8J-25
TRACTION CONTROL MALFUNCTION
INDICATOR - OPERATION..............8J-25
TRAILER HITCH - INSTALLATION........13-10
TRAILER HITCH - REMOVAL.............13-9
TRANSDUCER - DESCRIPTION, A/C
PRESSURE.........................24-13
TRANSDUCER - DIAGNOSIS AND
TESTING, A/C PRESSURE..............24-13
TRANSDUCER - INSTALLATION, A/C
PRESSURE.........................24-14
TRANSDUCER - INSTALLATION, VACUUM . . 11-8
TRANSDUCER - OPERATION, A/C
PRESSURE.........................24-13
TRANSDUCER - REMOVAL, A/C
PRESSURE.........................24-14
TRANSDUCER - REMOVAL, VACUUM......11-7
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC............21-23,21-24
TRANSMISSION - INSTALLATION, REAR
CROSSMEMBER......................13-9
TRANSMISSION - NAG1 - DESCRIPTION,
AUTOMATIC..........................21-2
TRANSMISSION - NAG1 - OPERATION,
AUTOMATIC..........................21-4
TRANSMISSION - REMOVAL, REAR
CROSSMEMBER......................13-9
TRANSMISSION - SPECIAL TOOLS,
NAG1 AUTOMATIC....................21-69
TRANSMISSION - SPECIFICATIONS,
NAG1 AUTOMATIC....................21-68
TRANSMISSION CONTROL MODULE -
DESCRIPTION........................8E-5
TRANSMISSION CONTROL MODULE -
OPERATION..........................8E-5
TRANSMISSION FILL - STANDARD
PROCEDURE.......................21-103
TRANSMISSION FLUID - NAG1 -
DESCRIPTION, AUTOMATIC..............0-4
TRANSMISSION FLUID - OPERATION,
AUTOMATIC...........................0-4
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION.....................21-140
TRANSMISSION TEMPERATURE SENSOR
- OPERATION.......................21-141
TRANSMITTER - DESCRIPTION, REMOTE
KEYLESS ENTRY......................8N-2
TRANSPONDER KEY - DESCRIPTION......8Q-5
TRANSPONDER KEY - OPERATION........8Q-5
TRAY - DESCRIPTION, BATTERY.........8F-16
TRAY - INSTALLATION, BATTERY........8F-16
TRAY - INSTALLATION, TOP COVER......23-64
TRAY - OPERATION, BATTERY..........8F-16
TRAY - REMOVAL, BATTERY............8F-16
TRAY - REMOVAL, TOP COVER..........23-63
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-8
TRIM - INSTALLATION, A-PILLAR........23-68
TRIM - INSTALLATION, B-PILLAR........23-69
TRIM - INSTALLATION, COWL..........23-70
TRIM - INSTALLATION, D-PILLAR........23-70
TRIM - REMOVAL, A-PILLAR...........23-67
TRIM - REMOVAL, B-PILLAR...........23-68
TRIM - REMOVAL, COWL..............23-70
TRIM - REMOVAL, D-PILLAR...........23-70
TRIM PANEL - INSTALLATION.....23-20,23-35,
23-46
TRIM PANEL - INSTALLATION, BACKLITE
- BULKHEAD........................23-81
TRIM PANEL - INSTALLATION,
BULKHEAD.........................23-69
TRIM PANEL - INSTALLATION, QUARTER . . 23-72
TRIM PANEL - REMOVAL
....23-19,23-35,23-46
TRIM PANEL - REMOVAL, BACKLITE -
BULKHEAD
.........................23-81
TRIM PANEL - REMOVAL, BULKHEAD
....23-69
TRIM PANEL - REMOVAL, QUARTER
.....23-71
TUBE - INSTALLATION, EXHAUST
........24-73
VAINDEX 17
Description Group-Page Description Group-Page Description Group-Page